Search Results

An investigation of cyclic variability in a spark ignition engine is reported. Specifically, the predictions of an engine code have been compared with experimental data obtained using a well-characterized SI engine. The engine used for the experimental work and modeled in the code is the single cylinder research engine developed at Sandia National Laboratories and now operating at Drexel University. The data used for comparison were cylinder pressure histories for 110 engine cycles gathered during operation at a single engine operating condition. The code allows the various factors that could influence cyclic variability to be examined independently. Specifically, a model has been used to independently examine the effects of variations in equivalence ratio and of the turbulence intensity on cycle-to-cycle variations in the peak cylinder pressure, the crankangle of occurrence of peak pressure, the flame development angle, and the rapid burning angle.

Inevitably a fraction of the hydrocarbon fuel in spark ignition engines escapes in-cylinder combustion and flows out with the burned products. Post combustion oxidation in the cylinder and exhaust port may consume a part of this fuel and plays an important role in determining exhaust emission levels. This paper presents results from experiments designed to identify the factors that control post-combustion oxidation. Regulated exhaust components and detailed hydrocarbon species were measured using seven neat hydrocarbons and four blends as fuel. The fuels were selected to compare the relative rates of mixing and chemical kinetics. The results indicate that exhaust temperature, diffusion rates and fuel kinetics each play a complicated role in determining emission levels.

We investigated the ability of a reduced chemical kinetic model of 18 reactions and 13 active species to predict the heat release for a blend of primary reference fuels with octane rating 63 in a motored research engine. Given the initial fuel-air mixture concentration and temperature, the chemical kinetic model is used to predict temperature, heat release and species concentrations as a function of time or crank angle by integrating the coupled rate and energy equations. For comparison, we independently calculated heat release from measured pressure data using a standard thermodynamic model.

The detailed chemical reactions leading to autoignition of n-pentane are investigated in this study. A single-cylinder engine operating in a nonfired mode was used. The engine is supercharged and the temperature of the inlet fuel/air mixture is varied. By increasing the inlet manifold temperature, at a given inlet manifold pressure, the fuel/air mixture can be made to undergo autoignition. In-cylinder pressure and temperature profiles were measured. Gas samples from the combustion chamber were extracted and analyzed using gas chromatography techniques. The detailed chemical reaction mechanisms explaining the products from the different stages of the fuel oxidation process are presented. It is speculated that the generation of OH radicals from the peroxide (QOOH) decomposition is responsible for the autoignition of the n-pentane fuel/air mixture.

Autoignition chemistry of n-heptane, iso-octane and an 87 octane blend, 87 PRF, was studied in a single-cylinder modified Wisconsin model AENL engine under motored conditions. Use of a fast-acting sampling valve and gas chromatographic analysis allowed measurement of in-cylinder gas composition during the ignition process. Crank angle resolved species evolution profiles were generated for all three fuels at a fixed inlet temperature of 376 K. For n-heptane, the measurements were made during a cyclically repeatable two stage ignition process up to the point of hot ignition (the second stage ignition). These n-heptane experiments were run at ø = 0.3 to avoid excessive pressure rise at hot ignition which might damage our engine. iso-Octane and 87 PRF were run at stoichiometric equivalence ratio which did not have a second stage ignition, and species were measured only during the first stage of ignition.

Recently, we reported the development of a new reduced chemical kinetic model for predicting reactivity and autoignition behavior of primary reference fuels in a motored research engine. The predicted oxidation behavior (ignition delay, preignition heat release, and evolution of key chemical species) is in fairly good agreement with experiments. In addition, the model reproduced the experimentally observed dependence of overall reactivity on charge density and manifold inlet conditions. This paper reports our initial effort to apply this new reduced chemical kinetic model to other fuels. Specifically, the model was tested using neat n-butane and n-butane/iso-butane blends (10, 20, and 48 percent by volume iso-butane) under skip fired conditions. The only adjustments made in the model were to the fuel specific rate parameters of the RO2· isomerization reaction, the reaction of aldehydes with OH·, and the reaction forming cyclic ethers.