Search Results

In a harmonized ESA/NIVR project the performance of membrane gas absorption for the simultaneous removal of carbon dioxide and moisture has been determined experimentally at carbon dioxide and humidity concentration levels representative for spacecraft conditions. Performance data at several experimental conditions have been collected. Removal of moisture can be controlled by the temperature of the absorption liquid. Removal of carbon dioxide is slightly affected by the temperature of the absorption liquid. Based on these measurements a conceptual design for a carbon dioxide and humidity control system for the Crew Transport Vehicle (CTV) is made. For the regeneration step in this design a number of assumptions have been made. The multifunctionality of membrane gas absorption makes it possible to combine a number of functions in one compact system.

Because of the reduction on the remaining Shuttle launches, the initial mission that was assigned for MELFI, the Minus Eighty degrees Celsius Laboratory Freezer for ISS, has been significantly modified. While the design was made for a MELFI flying 15 times over a period of 10 years with individual missions no longer than 2 years, present scenario requires to have MELFI in orbit up to 7 years. Extending the MELFI on orbit life from two to seven years has required staggered assessments, each of them aiming at preserving as much as possible the existing design. The potential life limited items are evaluated. On orbit maintenance will be extended for a longer period and maintenance activities foreseen initially to be done on ground between flights will be adapted for orbit. Degraded modes are evaluated so that MELFI ensures its mission at the end of the life even with some off-nominal conditions.

Columbus has been delivered to Kennedy Space Center (KSC) in summer 2006 for final integration, test and mission preparation. In the frame of these “last” phase activities also the Active Thermal Control System (ATCS) had to be finalized and prepared for the launch resp. mission. Due to unexpected late failures resp. malfunctions detected on component/unit level of the ATCS, refurbishment, integration / exchange of the relevant components and re-testing of their system level functions had to be done. Moreover, the still outstanding system level fluid leakage test of the ATCS had to be revised and completed. In addition to the required late refurbishment, integration and test activities, in certain cases also operational workarounds had to be evaluated. They should help to cope with similar contingency situations during operation of the ATCS on-orbit.

Methane-filled heat pipes have been developed and qualified for the SCIAMACHY thermal bus assembly. The heat pipes provide an efficient heat transfer in the temperature range 100-160 K. Extensive qualification testing has been performed. The thermal bus assembly is part of the Thermal Bus Unit (TBU) of the SCIAMACHY Radiant Cooler.

An advanced trace gas monitoring system for long duration manned space missions - such as the International Space Station - is discussed. The system proposed is a combination of a Fourier-Transform Infrared Spectrometer (FTIR) and a distributed ‘Smart Gas Sensor system (SGS). In a running multi-phase programme [1,2] the FTIR technology, applying novel analysis methods, has been demonstrated to handle multi-component gas measurements, including identification and quantification of 20 important trace gases in a mixture. In the current phase 3, initiated end of 1997, a fully operational FTIR technology demonstration model will be manufactured and tested. The SGS consists of an array of twenty electrically conductive polymer sensors supplemented with an array of quartz crystal microbalance sensors. The technology has been tested on the Russian MIR space station and is currently miniaturized into a second-generation flight model.

The Automated Transfer Vehicle (ATV) is a European Space Agency autonomous, expendable logistic transportation system for Low Earth Orbit. The ATV will be launched by Ariane 5 and its mission is to contribute to the logistic servicing of the International Space Station: via the delivery of a cargo (crew items, scientific experiments, spare parts..) as well as of fluids such as propellant, water and compressed air via the provision of an extra service consisting of retrieving the station wastes when departing (replacing the upcoming cargo) and getting rid of them through the final destructive atmospheric re-entry of the ATV itself via the contribution to the orbit control of ISS by providing a reboost and attitude control capability to the ISS. The ATV consists of a Spacecraft and an Integrated Cargo Carrier. The Spacecraft includes all subsystems necessary for the automated flight to the ISS and for the reboost, including the propellant tanks and the thrusters.

Final preparation and configuration of the Columbus module at the Kennedy Space Center (KSC) required the performance of system level tests with the Active Thermal Control System (ATCS). These tests represented the very last system level activities having been concluded on the Columbus module before handover to NASA for space shuttle integration. Those very last tests, performed with the ATCS comprised the final ATCS Leakage Test, the final calibration and adjustment of the Water Flow Selection Valves (WFSV) and Water On/Off Valves (WOOV) as well as a sophisticated ATCS Residual Air Removal test. The above listed tests have been successfully performed and test data evaluated for verification closeout as well as input delivery for operational Flight Rules and Procedures. Some of the above mentioned tests have been performed the first time hence, a succeeding lessons learned collection followed in order to improve the perspectives of future tests.

After several years of development the first European Automated Transfer Vehicle (ATV) developed by ESA called Jules Verne completed successfully its seven-month ISS logistics mission. Launched the 9 March 2008 on an Ariane 5 launcher, the ATV performed the 3 April 2008 its rendezvous and docking to the International Space Station to which it remained attached for five months. This paper presents in a first part the ATV thermal control architecture based on a innovative active thermal control design built around 40 Variable Conductance Heat Pipes (VCHP) controlling the heat rejection and in a second part the in-flight thermal control behavior of the ATV Jules Verne observed during the seven months mission in both free flight and attached to ISS phases.

In recent years there is growing interest, on the part of the remote sensing community, in using the Antarctic area, for calibrating and validating data of satellite-borne microwave radiometers. With a view to the launching of the ESA's SMOS satellite, which is a satellite designed to observe soil moisture over the Earth landmasses, salinity over the oceans and to provide observations over regions of ice and snow, an experimental activity called DOMEX was started at Dome-C Antarctica. The main scientific objectives of this activity are to provide microwave data for SMOS satellite calibration and in particular: the continuous acquisition of a calibrated time-series of microwave and thermal Infrared (8-14micron) emission over an entire Austral annual cycle, the acquisition of a long time-series of snow measurements and the acquisition of relevant local atmospheric measurements from the local weather station. This paper is focusing on the thermal design, analysis and testing of Domex-2.

A Heat Switch has been developed, namely a device able to autonomously regulate its own thermal conductance in function of the equipment dissipation and environmental heat sink conditions. It is based on a Loop Heat Pipe (LHP) technology, with a passive bypass valve which diverts the flow to the Compensation Chamber when needed for regulation purposes. The target application is the potential use on a Mars Rover thermal control system. The paper recalls the Heat Switch design, and reports the results of an extensive test campaign on the ground demonstrator. The performance of the device was found extremely satisfying, and often exceeded the system requirements.

Jules Verne (JV) is the name of the first Automated Transfer Vehicle (ATV) developed by ASTRIUM Space Transportation on behalf of European Space Agency (ESA). JV was launched the 9 March 2008 by ARIANE 5 and performed the 3 April 2008 its automatic rendezvous and docking to the International Space Station (ISS) to which it remained attached up to the 5 September 2008. In the meantime, JV has provided the ISS with dry and fluid cargo and performed one refueling, four ISS re-boosts and one Debris Avoidance Maneuver. JV completed its successful mission by offloading waste and was destroyed during its re-entry the 29 September 2008. Generally, development and verification of Power management rely on classical thermal and electrical engineering.

Jules Verne – the first ATV model developed by ASTRIUM on behalf of ESA – has been controlled by CNES Toulouse Control Centre from March to September 2008. The Engineering Support Team (EST) was in charge to provide System expertise and to propose relevant recommendations in case of off nominal situations. This paper deals with the operations carried out by the EST Thermal position during the JV flight, such as: Identification of thermal anomalies triggered by onboard software or by ground monitoring; Analysis of actual situation from available flight data; Correction implemented thanks to a complete set of commands and procedures; Check on the on-board configuration after correction uploading.

Membrane gas absorption and desorption (MGA/MGD) for the removal of CO2 in manned spacecraft or other enclosed environment is subject of study by Stork and TNO for many years. The system is based on the combination of membrane separation and gas absorption. Advantage of this technology is that the system not only can be used to remove the carbon dioxide but also to control the relative humidity and temperature. Absorption of moisture and heat is achieved by cooling the absorption liquid below the dewpoint temperature of the gas stream. From the start in 1995, the Crew Transfer Vehicle is used as a basis for the design (1,2). Compared to the planned air conditioning system, consisting of a condensing heat exchanger, LiOH cartridges and a water evaporator assembly, MGA/MGD shows advantage in volume, mass and power consumption. The absorption liquid circulates through the spacecraft thermal control loop, replacing the coolant water.

This work concerns the model of a biological life support system consisting of higher plants, a unit of “biological combustion”, a physicochemical reactor, and 1/30 of a human. The cycling of the main biogenic elements of the system, water, and carbon dioxide was closed to a high degree (more than 95%). Experimental-theoretical analysis of the cycling processes in the system was based on the calculations of mass exchange rates dynamics and some stoichiometric equations. The model was designed for the study of mechanisms of material transformation and the directions of mass exchange processes in the artificial ecosystems.

EcosimPro‘s capability to solve a problem domain that can be represented by Differential-Algebraic Equations (DAE) and discrete events, make it particularly attractive to model bio-regenerative life support systems. Components of the envisaged MELiSSA bio-regenerative life support system are driven by the adaptation of the biomass to changing environmental conditions, which could be of continuous nature, such as depletion or replenishment of nutrition, and discrete events, such as step changes in light fluxes and control interactions. The authors first present simulation results for a closed and an open loop bio-regenerative system. The simulations include the establishment of a quasi-steady state, reaction to step changes including a mass balance check, and the simulation of a controlled bioreactor. The results demonstrate the capability of this tool to model components of a bio-regenerative life support system, as well as an entire bio-regenerative life support system in the future.

The Automated Transfer Vehicle will provide ISS with reboost, attitude control functions, with water, gas and propellant and with dry cargo. It is a 20 tons expendable vehicle launched by Ariane. It performs a rendezvous and docking with the Russian Segment. It remains attached up to 6 months before a destructive reentry. During PDR campaign, it was decided to change the ATV Thermal Control System from semi-passive (see reference 1) to active system to comply with electrical power budget and get the ATV power autonomy. This system is based on 40 Variable Conductance Heat Pipes controlling the heat rejection of the avionics items toward space. This paper presents the new thermal control system of the ATV and its verification and qualification logic.

Temperature and humidity control are vital functions of an environmental control and life support system in a manned spacecraft. A MCHX Technology Demonstrator has been developed using hollow fiber membranes to remove heat and water vapor from the cabin air. The functional principle of the MCHX is based on micro porous hydrophobic hollow fiber membranes. Heat and water vapor are transferred through the membrane to the cooling the water. The water vapor will condense at the cooling water side. The technique promises a good alternative for the conventional noisy and power-consuming rotary condensate separator. This paper describes the MCHX development work including the rational for its concept, the module design and its performance data as a result of numerical predictions and a test campaign. The MCHX performance requirements are linked to those of the Columbus Laboratory, the European contribution to the International Space Station (ISS).

The Hubble space telescope (HST) solar array consists of two identical double roll-out wings designed after the Hughes flexible roll-up solar array (FRUSA) and was developed by the European Space Agency (ESA) to meet specified HST power output requirements at the end of 2 years, with a functional lifetime of 5 years. The requirement that the HST solar array remain functional both mechanically and electrically during its 5-year lifetime meant that the array must withstand 30,000 low-Earth orbit (LEO) thermal cycles between approximately +100 and -100 °C. In order to evaluate the ability of the array to meet this requirement, an accelerated thermal cycle test in vacuum was conducted at NASA's Marshall Space Flight Center (MSFC), using two 128-cell solar array modules which duplicated the flight HST solar array. Several other tests were performed on the modules.

The MELISSA (Microbial Ecological LIfe Support System Alternative) project has been set up to be a model for the studies on ecological life support systems for long term space missions. The compartmentalisation of the loop, the choice of the micro-organisms and the axenic conditions have been selected in order to simplify the behaviour of this artificial ecosystem and allow a deterministic and engineering approach. In this framework the MELISSA project has now been running since beginning 1989. In this paper we present the general approach of the study, the scientific results obtained on each independent compartment (mass balance, growth kinetics, limitations, compound conversions,..), the tests of toxicity already performed between some compartments and their effect on the growth kinetics. The technical results on instrumentation and control aspects, and the current status of the ESA/ESTEC hardware are also reviewed.

During Extravehicular Activities (EVA) an astronaut has to be protected against various external factors ranging from mechanical hazards to solar radiation and micrometeoroids. An important element in this external protection is the outermost fabric layer. It has to ensure the mechanical protection of the pressure retention bladder and at the same time - by its thermooptical properties - plays an important role in the thermal control of the space suit. New weaving and knitting technologies enable the fabrication of so-called 3-D fabrics with interconnected layers and local variation of properties in one manufacturing step. By this a tailored design of protection properties is possible. A study has been performed to define concepts adapted for use on a European Space Suit. Different fabric samples were manufactured and tested, amongst others, for strength, flexibility, puncture and wear resistance, UV stability, flammability, out/offgassing and micrometeoroid protection effctiveness.