Criteria

Text:
Sector:
Display:

Results

Viewing 1 to 30 of 70
2017-06-05
WIP Standard
AIR6808
This SAE Aerospace Information Report (AIR) is limited to the requirements of AS50881 and examines these requirements providing rationale behind them. SAE AS50881 is only applicable to the aircraft electrical wiring and interconnect system (EWIS). Pods and other devices that can be attached to an aircraft that are considered as aircraft equipment design. The AS50881 scope does not include attached devices, but does include the interface between the pod and aircraft wiring. Paragraph 3.3.5 addresses components such as antennas and other similar equipment that was once supplied as GFAE.
CURRENT
2014-08-26
Standard
ARP5614
This ARP specifies the recommended methods of marking electrical wiring and harnesses to aid in the positioning/routing of electrical wiring, harnesses and cable assemblies.
CURRENT
2013-11-11
Standard
ARP6167
This SAE Aerospace Recommended Practice (ARP) describes the etching of fluoropolymer electrical wire insulations to ensure that all facets of the process from the chemistry to the processing, to the storage and handling are well defined.
CURRENT
2016-12-01
Standard
ARP5369B
These guidelines have been written to provide process information regarding the hot stamp method of marking wire identification directly on aerospace wires and cables.
HISTORICAL
2010-08-05
Standard
ARP5369A
These guidelines have been written to provide process information regarding the hot stamp method of marking wire identification directly on aerospace wires and cables.
CURRENT
2011-07-07
Standard
AS25067A
CURRENT
2011-07-07
Standard
AS25064A
CURRENT
2011-07-07
Standard
AS25065A
CURRENT
2016-01-09
Standard
ARP81490A
This document covers the general recommendations for Transverse Electromagnetic Mode (TEM) Transmission Lines intended for use in airborne systems (see 6.2.14). For U.S military applications, TEM Transmission Lines shall meet the requirements in accordance with MIL-T-81490. The follow index lists the recommended requirements and methods covered by the Aerospace Recommended Practice (ARP):
CURRENT
2009-12-30
Standard
AIR5717
Wire and cable products progress through a series of handling or operational steps from the time they leave the manufacturer, and until a finished harness or assembly is ready for installation on a vehicle. Throughout these many steps, environmental or processing conditions may be present which can generate damage detrimental to the wire or cable and/or its intended application.
CURRENT
1992-03-23
Standard
AIR4465
This document presents design and application information which will allow optimized utilization of filter line wire and cable purchased to MIL-C-85485. Filter line wire is defined and design information is presented. The electrical and mechanical performance characteristics of the wire along with recommended harnessing methods and techniques are also presented.
CURRENT
2009-05-28
Standard
AIR5558
The purpose of this report is to provide information on the results of ultra violet (UV) laser marking and mark contrast measurement of a wide range of aerospace wire and cable constructions, the specifications for most of which do not state specific requirements for laser markability. The contents of this document are for information and guidance only. It is not intended that it be used as the basis for marking process specifications or standards, which are covered by AS5649 Wire and Cable Marking Process, UV Laser.
CURRENT
2017-01-24
Standard
AIR5575A
This SAE Aerospace Information Report (AIR) discusses the often overlooked relationship between hot stamp marking and the environmental conditions that contribute aircraft wiring problems and discusses current beliefs of military service experts, regulatory agencies and industry standard writing bodies about the potential hazards imposed by the hot stamping process.
HISTORICAL
1999-07-01
Standard
AS25064
HISTORICAL
2004-05-04
Standard
AS25065
HISTORICAL
2004-05-04
Standard
AS25067
HISTORICAL
1998-11-01
Standard
ARP5369
These guidelines have been written to provide process information regarding the hot stamp method of marking wire identification directly on aerospace wires and cables.
HISTORICAL
1998-04-01
Standard
ARP5062
The purpose of this SAE Aerospace Recommended Practice (ARP) is to provide recommended test fluids for testing of electrical components used on aircraft exterior or for ground support near aircraft. These fluids were selected based on a consolidation of test fluids used by military and commercial sources and on review of national and international component specifications. These recommendations are general guidelines. Safety factors for any unusual testing applications or operating conditions should be given special consideration by the designer. The test fluids provided are intended to be recommendations and are not intended to limit or supersede those recommended by aircraft or ground support equipment manufacturers.
CURRENT
2012-11-21
Standard
ARP5062A
The purpose of this SAE Aerospace Recommended Practice (ARP) is to provide recommended test fluids for testing of electrical components used on aircraft exterior or for ground support near aircraft. These fluids were selected based on a consolidation of test fluids used by military and commercial sources and on review of national and international component specifications. These recommendations are general guidelines. Safety factors for any unusual testing applications or operating conditions should be given special consideration by the designer. The test fluids provided are intended to be recommendations and are not intended to limit or supersede those recommended by aircraft or ground support equipment manufacturers.
HISTORICAL
2004-05-25
Standard
ARP81490
This document covers the general requirements for Transverse Electromagnetic Mode (TEM) Transmission Lines (see 6.4.14) intended for use in airborne systems.
Viewing 1 to 30 of 70