Search Results

Existing gasoline DI injection equipment has been modified to generate single hole pulsed gas jets. Injection experiments have been performed at combinations of 3 different pressure ratios (2 of which supercritical) respectively 3 different hole geometries (i.e. length to diameter ratios). Injection was into a pressure chamber with optical access. Injection pressures and injector hole geometry were selected to be representative of current and near-future DI natural gas engines. Each injector hole design has been characterized by measuring its discharge coefficient for different Re-levels. Transient jets produced by these injectors have been visualized using planar laser sheet Mie scattering (PLMS). For this the injected gas was seeded with small oil droplets. The corresponding flow field was measured using particle image velocimetry (PIV) laser diagnostics.

Cylinder pressure-based combustion control is widely introduced for passenger cars. Benefits include enhanced emission robustness to fuel quality variation, reduced fuel consumption due to more accurate (multi-pulse) fuel injection, and minimized after treatment size. In addition, it enables the introduction of advanced, high-efficient combustion concepts. The application in truck engines is foreseen, but challenges need to be overcome related to durability, increased system costs, and impact on the cylinder head. In this paper, a new single cylinder pressure sensor concept for heavy-duty Diesel engines is presented. Compared to previous studies, this work focuses on heavy-duty Diesel powertrains, which are characterized by a relatively flexible crank shaft in contrast to the existing passenger car applications.

An experimental analysis was executed on a NA (Natural Aspirated) 4-stroke gasoline engine to investigate the potential of exhaust waste energy recovery using power turbine technology for light duty application. Restrictions with decreasing diameter were mounted in the exhaust to simulate different vane positions of a VGT (Variable Geometry Turbine) and in-cylinder pressure measurements were performed to evaluate the effect of increased exhaust back pressure on intake- and exhaust pumping losses and on engine performance. Test points in the engine map were chosen on the basis of high residence time for the vehicle during the NEDC (New European Driving Cycle). The theoretically retrievable power was calculated in case a turbine is mounted instead of a restriction and the net balance was obtained between pumping power losses and recovered energy.

Partially Premixed Combustion has shown the potential of low emissions of nitrogen oxides (NOx) and soot with a simultaneous improvement in fuel efficiency. Several research groups have shown that a load range from idle to full load is possible, when using low-octane-number refinery streams, in the gasoline boiling range. As such refinery streams are not expected to be commercially available on the short term, the use of naphtha blends that are commercially available could provide a practical solution. The three blends used in this investigation have been tested in a single-cylinder engine for their emission and efficiency performance. Besides a presentation of the sensitivity to injection strategies, dilution levels and fuel pressure, emission performance is compared to legislated emission levels. Conventional diesel combustion benchmarks are used for reference to show possible improvements in indicated efficiency.

This paper reports on a study of a large number of blends of a low-sulfur EN-590 type diesel fuel respectively of a Swedish Class 1 fuel and of a synthetic diesel with different types of oxygenates. Oxygen mass fraction of the blends varied between 0 and 15 %. For comparison, the fuel matrix was extended with non-oxygenated blends including a diesel/water emulsion. Tests were performed on a modern multi-cylinder HD DAF engine equipped with cooled EGR for enabling NOx-levels between 2.0 and 3.5 g/kWh on EN-590 diesel fuel. Additional tests were done on a Volvo Euro-2 type HD engine with very low PM emission. Finally, for some blends, combustion progress and soot illumination was registered when tested on a single cylinder research engine with optical access. The results confirm the importance of oxygen mass fraction of the fuel blend, but at the same time illustrate the effect of chemical structure: some oxygenates are twice as effective in reducing PM as other well-known oxygenates.

To meet 2010 emission targets, optimal SCR system performance is required. In addition, attention has to be paid to in-use compliance requirements. Closed-loop control seems an attractive option to meet the formulated goals. This study deals with the potential and limitations of closed-loop SCR control. High NOx conversion in combination with acceptable NH3 slip can be realized with an open-loop control strategy. However, closed-loop control is needed to make the SCR system robust for urea dosage inaccuracy, catalyst ageing and NOx engine-out variations. Then, the system meets conformity of production and in-use compliance norms. To demonstrate the potential of closed-loop SCR control, a NOx sensor based control strategy with cross-sensitivity compensation is compared with an adaptive surface coverage/NH3 slip control strategy and an open-loop strategy. The adaptive surface coverage/NH3 slip control strategy shows best performance over simulated ESC and ETC cycles.

This paper first compares strengths and weaknesses of different options for performing optical diagnostics on HD diesel sprays. Then, practical experiences are described with the design and operation of a constant volume test cell over a period of more than five years. In this test rig, pre-combustion of a lean gas mixture is used to generate realistic gas mixture conditions prior to fuel injection. Spray growth, vaporization are studied using Schlieren and Mie scattering experiments. The Schlieren set-up is also used for registration of light emitted by the combustion process; this can also provide information on ignition delay and on soot lift-off length. The paper further describes difficulties encountered with image processing and suggests methods on how to deal with them.

Collision of injected fuel spray against the cylinder liner (wall-wetting) is one of the main hurdles that must be overcome in order for early direct injection Premixed Charge Compression Ignition (EDI PCCI) combustion to become a viable alternative for conventional DI diesel combustion. Preferably, the prevention of wall-wetting should be realized in a way of selecting appropriate (most favorable) operating conditions (EGR level, intake temperature, injection timing-strategy etc.) rather than mechanical modification of an engine (combustion chamber shape, injector replacement etc.). This paper presents the effect of external uncooled EGR (different fraction) on wall-wetting issues specified by two parameters, i.e. measured smoke number (experiment) and liquid spray penetration (model).

An HSDI Diesel engine was fuelled with standard Swedish environmental class 1 Diesel fuel (MK1), Soy methyl ester (B100) and n-heptane (PRF0) to study the effects of both operating conditions and fuel properties on engine performance, resulting emissions and spray characteristics. All experiments were based on single injection diesel combustion. A load sweep was carried out between 2 and 10 bar IMEPg. For B100, a loss in combustion efficiency as well as ITE was observed at low load conditions. Observed differences in exhaust emissions were related to differences in mixing properties and spray characteristics. For B100, the emission results differed strongest at low load conditions but converged to MK1-like results with increasing load and increasing intake pressures. For these cases, spray geometry calculations indicated a longer spray tip penetration length. For low-density fuels (PRF0) the spray spreading angle was higher.

Though very important for the system performance, the dynamic behavior of the catalytic converter has mainly been neglected in the design of exhaust emission control systems. Since the major dynamic effects stem from the oxygen storage capabilities of the catalytic converter, a novel model-based control scheme, with the explicit control of the converter's oxygen storage level is proposed. The controlled variable cannot be measured, so it has to be predicted by an on-line running model (inferential sensor). The model accuracy and adaptability are therefore crucial. A simple algorithm for the model parameter identification is developed. All tests are performed on a previously developed first principle model of the catalytic converter so that the controller effectiveness and performance can clearly be observed.

In this work, the influences of aromatics on combustion and emission characteristics from a heavy-duty diesel engine under various loads and exhaust gas recirculation (EGR) conditions are investigated. Tests were performed on a modified single-cylinder, constant-speed and direct-injection diesel engine. An engine exhaust particle sizer (EEPS) was used in the experiments to measure the size distribution of engine-exhaust particle emissions in the range from 5.6 to 560 nm. Two ternary blends of n-heptane, iso-octane with either toluene or benzaldehyde denoted as TRF and CRF, were tested, diesel was also tested as a reference. Test results showed that TRF has the longest ignition delay, thus providing the largest premixed fraction which is beneficial to reduce soot. However, as the load increases, higher incylinder pressure and temperature make all test fuels burn easily, leading to shorter ignition delays and more diffusion combustion.

The Free Space Parameter (FSP) is evaluated as a predictor for the efficiency of a Variable Geometry Turbine (VGT). Experiments show an optimum value at 2 times the vane height. However, the optimum was found to be dependent on the pressure ratio, yielding an optimum closer to 2.5 at pressures of 2 and 2.5 bar. After this validation the FSP of a conventional VGT is evaluated and an attempt is made to improve the efficiency of this turbine using the FSP. A new geometry is proposed which yields more favorable FSP values. Experiments show that at the original design point the efficiency is unchanged. However, at both larger and smaller nozzle area’s the turbine efficiency improves as predicted by the FSP values. A relative efficiency improvement of 3 to 28 % is attained.

Recently introduced sulfur caps on marine fuels in so-called sulfur emission control areas (SECAs) are forcing shipping companies to sail on more or less automotive grade diesel in lieu of the considerably less expensive, but sulfur-laden heavy fuel oil (HFO) to which they were accustomed. This development is an opportunity for a bio-based substitute, given that most biomass is sulfur free by default. Moreover, given that biomass is typically solid to start with, cracking it to an HFO grade, which is highly viscous in nature, will involve fewer and/or less harsh process steps than would be the case if an automotive grade fuel were to be targeted. In this study, a renewable low sulfur heavy fuel oil (LSHFO) has been produced by means of subcritical water assisted lignin depolymerization in the presence of a short length surfactant, ethylene glycol monobutyl ether (EGBE).

Reactivity controlled compression ignition through in-cylinder blending gasoline and diesel to a desired reactivity has previously been shown to give low emission levels and a clear simultaneous efficiency advantage. To determine the possible viability of the concept for on-road application, the control space of injection parameters with respect to combustion phasing is presented. Four injection strategies have been investigated, and for each the respective combustion phasing response is presented. Combustion efficiency is shown to be greatly affected by both the injection-timing and injection-strategy. All injection strategies are shown to break with the common soot-NOx trade-off, with both smoke and NOx emissions being near or even below upcoming legislated levels. Lastly, pressure rise rates are comparable with conventional combustion regimes with the same phasing. The pressure rise rates are effectively suppressed by the high dilution rates used.

Post-injection strategies prove to be a valuable option for reducing soot emission, but experimental results often differ from publication to publication. These discrepancies are likely caused by the selected operating conditions and engine hardware in separate studies. Efforts to optimize not only engine-out soot, but simultaneously fuel economy and emissions of nitrogen oxides (NOx) complicate the understanding of post-injection effects even more. Still, the large amount of published work on the topic is gradually forming a consensus. In the current work, a Design-of-Experiments (DoE) procedure and regression analysis are used to investigate the influence of various operating conditions on post-injection scheduling and efficacy. The study targets emission reductions of soot and NOx, as well as fuel economy improvements. Experiments are conducted on a heavy-duty compression ignition engine at three load-speed combinations.

Controlling ignition delay is the key to successfully enable partially premixed combustion in diesel engines. This paper presents experimental results of partially premixed combustion in an optically accessible engine, using primary reference fuels in combination with artificial exhaust gas recirculation. By changing the fuel composition and oxygen concentration, the ignition delay is changed. To determine the position of the flame front, high-speed visualization of OH-chemiluminescence is used, enabling a cycle-resolved analysis of OH formation. A clear correlation is observed between ignition delay and flame location. The mixing of fuel and air during the ignition delay period defines the local equivalence ratio, which is estimated based on a spherical combustion volume for each spray. The corresponding emission measurements using fast-response analyzers of CO, HC and NOX confirm the decrease in local equivalence ratio as a function of ignition delay.

Recently, some studies have shown high efficiencies using controlled auto-ignition by blending gasoline and diesel to a desired reactivity. This concept has been shown to give high efficiency and, because of the largely premixed charge, low emission levels. The origin of this high efficiency, however, has only partly been explained. Part of it was attributed to a lower temperature combustion, originating in lower heat losses. Another part of the gain was attributed to a faster, more Otto-like (i.e. constant volume) combustion. Since the concept was mainly demonstrated on one single test setup so far, an experimental study has been performed to reproduce these results and gain more insight into their origin. Therefore one cylinder of a heavy duty test engine has been equipped with an intake port gasoline injection system, primarily to investigate the effects of the balance between the two fuels, and the timing of the diesel injection.

A Gasoline Compression Ignition combustion strategy was developed and showed its capabilities in the heavy duty single cylinder test-cell, resulting in indicated efficiencies up to 50% and low engine out emissions applying to EU VI and US 10 legislations while the soot remained at a controllable 1.5 FSN. For this concept a single-cylinder CI-engine was used running at a lambda of ∼1.6 and EGR levels of ∼50% and a modified injection strategy. Part of this strategy was also the use of a gasoline blended with an ignition improver, giving the blend a cetane number in the range of regular diesel; ∼50. In this paper a step is taken towards implementation of this combustion concept into a multi-cylinder light duty standalone CI-engine. A standard CI-engine was modified so that its gas-exchange system could deliver the requested amounts of EGR and lambda.

A model-based control approach is proposed to give proper reference for the feed-forward combustion control of Partially Pre-mixed Combustion (PPC) engines. The current study presents a simplified first principal model, which has been developed to provide a base estimation of the ignition properties. This model is used to describe the behavior of a single-cylinder heavy-duty diesel engine fueled with a mix of bio-butanol and n-heptane (80vol% bio-butanol and 20 vol% n-heptane). The model has been validated at 8 bar gross Indicated Mean Effective Pressure (gIMEP) in PPC mode. Inlet temperature and pressure have been varied to test the model capabilities. First the experiments were conducted to generate reference points with BH80 under PPC conditions. And then CFD simulations were conducted to give initial parameter set up, e.g. fuel distribution, zone dividing, for the multi-zone model.

The accepted model of conventional diesel combustion [1] assumes a rich premixed flame slightly downstream of the maximum liquid penetration. The soot generated by this rich premixed flame is burnt out by a subsequent diffusion flame at the head of the jet. Even in situations in which the centre of combustion (CA50) is phased optimally to maximize efficiency, slow late stage combustion can still have a significant detrimental impact on thermal efficiency. Data is presented on potential late-stage combustion improvers in a EURO VI compliant HD engine at a range of speed and load points. The operating conditions (e.g. injection timings, EGR levels) were based on a EURO VI calibration which targets 3 g/kWh of engine-out NOx. Rates of heat release were determined from the pressure sensor data. To investigate late stage combustion, focus was made on the position in the cycle at which 90% of the fuel had combusted (CA90). An EN590 compliant fuel was tested.