Search Results

A simulation technology has been developed to enable prediction of galvanic corrosion in chassis parts where two different materials, iron and aluminum, come into contact with each other. When polarization curves representing a corrosive environment are input, this simulation technology calculates the corrosion current to flow and outputs the volume of aluminum corrosion to be formed near the iron-aluminum interface. The simulation makes it possible to predict the depth of corrosion that may occur in automobiles in the market.

Honda has developed an “Independent Left and Right Rear Toe Control System” that can achieve stable cornering performance and agile handling. We believe the issue that should be resolved in the next generation of ESC is the expansion of stability and agility into the general operation area. We examined how to accomplish this aim, and control of the independent rear toe angle was decided to be an appropriate method. In addition, a method for mounting the system without using a dedicated suspension was proposed. If left and right toe angles can be controlled independently, toe angle control and normal 4WS control become possible at the same time. In this paper, we will discuss the fundamental principle of independent toe angle control and the system configuration. Also, “INOMAMA Handling” (at driver's will) achieved by this system, as well as the fun and safe driving that are achieved as a result will be shown.

In this paper, we propose a hardware and a software design method considering functional safety for an electro-mechanical brake (EMB) control system which is used as a brake actuator in a brake-by-wire (BBW) system. A BBW system is usually composed of electro-mechanical calipers, a pedal simulator, and a control system. This simple by-wire structure eliminates the majority of bulky hydraulic brake devices such as boosters and master cylinders. The other benefit of a BBW system is its direct and independent response; this leads to enhanced controllability, thus resulting in not only improved basic braking performance but also considerably easier cooperative regenerative braking in hybrid, fuel-cell, and electric cars. The importance of a functional safety based approach to EMB electronic control unit (ECU) design has been emphasized because of its safety critical functions, which are executed with the aid of many electric actuators, sensors, and application software.

In this research, a three degree-of-freedom (DOF) rack-type electric-based power steering (EPS) model is developed. The model is coupled with a three DOF vehicle model and includes EPS maps as well as non-linear attributes such as vibration and friction characteristics of the steering system. The model is simulated using Matlab's Simulink. The vibration levels are quantified using on-vehicle straight-line test data where strain-gauge transducers are placed in the tie-rod ends. Full vehicle kinematic and compliance tests are used to verify the total steering system stiffness levels. Frequency response tests are used to adjust tire cornering stiffness levels as well as the tire dynamic characteristics such that vehicle static gain and yaw natural frequency are achieved. On-center discrete sinusoidal on-vehicle tests are used to further validate the model.

Recently vehicle development timeline is becoming shorter, so there is an urgent need to be able to develop vehicles with limited resources. This means the efficiency of the body structure development process must be improved. Specifically it is important to reduce the amount of design re-work required to meet performance targets as this can have a large influence on the body development time. In order to reduce the afore mentioned design re-work, we developed simple calculation models to apply a “V-Flow Development Process” to the preliminary stage design of the automobile body structure. The “V-Flow” advantages are as follows: (1) simple and easy to use, (2) defects are found at early stage, (3) avoids the downward flow of the defects. The advantage of preliminary stage design is that there is design flexibility since not many specifications have been determined yet.

The development and calibration of stress state-dependent failure criteria for advanced high-strength steel (AHSS) and aluminum alloys requires characterization under proportional loading conditions. Traditional tests to construct a forming limit diagram (FLD), such as Marciniak or Nakazima tests, are based upon identifying the onset of strain localization or a tensile instability (neck). However, the onset of localization is strongly dependent on the through-thickness strain gradient that can delay or suppress the formation of a tensile instability so that cracking may occur before localization. As a result, the material fracture limit becomes the effective forming limit in deformation modes with severe through-thickness strain gradients, and this is not considered in the traditional FLD. In this study, a novel bending test apparatus was developed based upon the VDA 238-100 specification to characterize fracture in plane strain bending using digital image correlation (DIC).

This study developed technology for simultaneously welding heterogeneous resin tubes in order to weld and integrate resin tubes with two different specifications (low temperature and high temperature). The aim of integration was cost and weight reduction. The cost reduction due to reducing the number of parts exceeded the increase in material cost due to a change to resin materials. Base material fracture of the resin tubes was set as the breaking format condition, and the welding parameters of the joint part rotations and the friction time between the joint part and the resin tubes were specified as the weld strength judgment standard. In addition, the fused thickness determined by observing the cross-section after welding was specified as the weld quality judgment standard. The range over which weld boundary peeling does not occur and weld strength is manifest was clarified by controlling the welding parameters and the fused thickness.

The SAE Fuel Cell Vehicle (FCV) Safety Working Group has been addressing FCV safety for over 9 years. The initial document, SAE J2578, was published in 2002. SAE J2578 has been valuable as a Recommended Practice for FCV development with regard to the identification of hazards and the definition of countermeasures to mitigate these hazards such that FCVs can be operated in the same manner as conventional gasoline internal combustion engine (ICE)-powered vehicles. SAE J2578 is currently being revised so that it will continue to be relevant as FCV development moves forward. For example, test methods were refined to verify the acceptability of hydrogen discharges when parking in residential garages and commercial structures and after crash tests prescribed by government regulation, and electrical requirements were updated to reflect the complexities of modern electrical circuits which interconnect both AC and DC circuits to improve efficiency and reduce cost.

The SAE FCV Safety Working Group has been addressing fuel cell vehicle (FCV) safety for over 8 years. The initial document, SAE J2578, was published in 2002. SAE J2578 has been valuable to FCV development with regard to the identification of hazards and the definition of countermeasures to mitigate these hazards such that FCVs can be operated in the same manner as conventional gasoline internal combustion engine (ICE)-powered vehicles. J2578 is currently being updated to clarify and update requirements so that it will continue to be relevant and useful in the future. An update to SAE J1766 for post-crash electrical safety was also published to reflect unique aspects of FCVs and to harmonize electrical requirements with international standards. In addition to revising SAE J2578 and J1766, the Working Group is also developing a new Technical Information Report (TIR) for vehicular hydrogen systems (SAE J2579).

With the introduction of the ISO26262 automotive safety standard there is a burden of proof to show that the processing elements in embedded microcontroller hardware are capable of supporting a certain diagnostic coverage level, depending on the required Automotive Safety Integrity Level (ASIL). The current mechanisms used to provide actual metrics of the Built-in Self Tests (BIST) and Lock Step comparators use Register Transfer Level (RTL) simulations of the internal processing elements which force faults into individual nodes of the design and collect diagnostic coverage results. Although this mechanism is robust, it can only be performed by semiconductor suppliers and is costly. This paper describes a new solution whereby the microcontroller is synthesized into a large Field Programmable Gate Array (FPGA) with a test controller on the outside.

FlexRay1 is a high speed, time triggered and fault tolerant communication protocol, which was specified to meet the requirements of safety-critical automotive applications. The achieved maturity of FlexRay encourages the implementation on silicon. The CIC-3102 device is a standalone controller provided by Infineon Technologies. It runs the wide spread E-Ray3 IP from Bosch. A complete communication node for FlexRay requires additional devices for the physical layer and the application part. The CIC-310 can communicate with a host controller via three different interfaces micro link interface MLI, serial synchronous interface SSC, external bus XMU. Its physical layer interface corresponds to the FlexRay specification. The CIC-310 provides features like intelligent move engines to maximize the achievable data rate as well as to minimize the workload of the host. Therefore, the CIC-310 allows a very flexible and efficient way to build and operate FlexRay nodes.

As the automotive industry quickly moves towards hybridized and electrified vehicles, the optimal integration of power electronics in these vehicles will have a significant impact not only on the cost, performance, reliability, and durability; but ultimately on customer acceptance and market success of these technologies. If properly executed with the right cost, performance, reliability and durability, then both the industry and the consumer will benefit. It is because of these interdependencies that the pace and scale of success, will hinge on effective collaboration. This collaboration will be built around the convergence of automotive and industrial technology. Where real time embedded controls mixes with high power and voltage levels. The industry has already seen several successful collaborations adapting power electronics to the automotive space in target vehicles.

The SAE Fuel Cell Vehicle (FCV) Safety Working Group has been addressing FCV safety for over 10 years. The initial document, SAE J2578, was published in 2002. SAE J2578 has been valuable as a Recommended Practice for FCV development with regard to the identification of hazards associated with the integration of hydrogen and electrical systems onto the vehicle and the definition of countermeasures to mitigate these hazards such that FCVs can be operated in the same manner as conventional gasoline internal combustion engine (ICE)-powered vehicles. An update to SAE J1766 for post-crash electrical safety was also published in 2008 to reflect unique aspects of FCVs and to harmonize electrical requirements with international standards. In addition to SAE J2578 and J1766, the SAE FCV Safety Working Group also developed a Technical Information Report (TIR) for vehicular hydrogen systems (SAE J2579).

It is the beginning of a new age: multicore technology from the PC desktop market is now also hitting the automotive domain after several years of maturation. New microcontrollers with two or more main processing cores have been announced to provide the next step change in available computing power while keeping costs and power consumption at a reasonable level. These new multicore devices should not be confused with the specialized safety microcontrollers using two redundant cores to detect possible hardware failures which are already available. Nor should they be confused with the heterogeneous multicore solutions employing an additional support core to offload a single main processing core from real-time tasks (e.g. handling peripherals).

Braking systems require a high system safety level: New safety concepts need to be implemented by reducing the system complexity. Microcontrollers with special safety functions are available with implemented features, self detecting and compensating different types of faults. Today usually two microcontrollers are used to check each other. Power devices provide microcontroller supplies and drive motors and valves; internally the functions are supervised to avoid incorrect system behaviour due to wrong voltages, currents, missing loads or other malfunctions. Bus interfaces, signal conditioning and interfaces for high voltage signals are integrated into the power system ICs. Latest BIPOLAR-CMOS-DMOS power technologies enable the power semiconductors to integrate logic functions.

Electronic throttle systems are becoming more and more important in today's motor vehicles. These systems consist of: a throttle valve with an electrical actuator and a transmission a position feedback an electronic acceleration pedal an electronic control unit (ECU) a semiconductor h-bridge for driving the motor. The electronic acceleration pedal gives a set point to the ECU. A control signal is generated and moves the motor of the throttle valve with a semiconductor h-bridge to the requested position. The voltage drop of a potentiometer is used here as control feedback signal. The potentiometer in the throttle valve is moved very often and has a rough environment like high temperature and vibrations. Therefore this system has a lot of problems with mechanical attrition and reliability during the whole system lifetime. The accuracy of the position control decreases over time.

Modern semiconductor devices enable highly efficient conversion of electrical power. Together with the microcontroller, they are the key elements for generation of the alternating currents from the car's DC supply that are necessary to drive high-performance units such as starter-alternators. These allow the combustion engine to crank up in several 100 ms and deliver up to 15 kW of electrical power. Smart driver ICs such as the TLE6280 enable the fast development of the interface between the microcontroller and the power switches. Currents of some 100A can be handled with the new OptiMOS FETs. Their rugged and ultra-low ohmic technology and their innovative packaging concepts, such as Power Modules and Power-Bonded MOSFETs, allow the building of compact and efficient control units.

Today's body and convenience applications in general directly control actuators and sensors from a single central electronic control unit (ECU). Future systems will be made of subsystem-clusters communicating via a local Class/A communication bus. This enables modular system design to reduce system complexity. For these types of new distributed applications the LIN bus is currently the most promising communication protocol. To allow a seamless migration from existing centralized to these next generation clustered system developers require software and hardware products for a homogenous and transparent LIN bus communication.

The objective of this SAE paper is to discuss a power stage partitioning which will provide a cost effective and flexible Infineon Technologies solution to control future E-Valve applications. To fulfil environmental demands, E-Valve applications will enable car manufacturers to: Dynamically reduce the number of working cylinders according to the drivers' torque requirements Have an efficient and variable control over the engine load in various conditions Dispense with throttles and exhaust recirculation valves The paper will describe: 1 The integration of the 4 MosFET and the future technology development required for the next system optimization. 2 Gate driver integration (3 different scenarios): Analog Interfacing between the μcontroller and the MosFETs with an integrated protection functionality (Scenario A).

Infineon proposes a Quasi-Autonomous Gate Driver (QAGD) to manage an electrically actuated component, whether electromechanical, electromagnetic, or electrohydraulic. This paper examines some current control strategies that can be implemented within the QAGD, such as: Synchronous Sampling (SYSA), Hysteresis, Improved Synchronous Sampling-Hysteresis (ISSH), Suboscillation, Suboscillation with Back EMF Feedforward (SBEF) and Synchronous Control in Rotation Coordinates (SCRC). Analysis and simulation of these strategies indicate their advantages and disadvantages, which are then summarized in a comparison chart, from which the best solution for a given application can be determined. The QAGD IC proposed by Infineon adopts this solution by integrating the current controller and the driver unit for the MOSFETs in a single package. The inverter function can therefore be implemented using one QAGD and several MOSFETs, which greatly simplify the system and decrease the costs.