Search Results

It has long been recognized that the key to achieving stringent emission standards such as ULEV is the control of cold-start hydrocarbons. This paper describes a new approach for achieving excellent cold-start hydrocarbon control. The most important component in the system is a catalyst that is highly active at ambient temperature for the exothermic CO oxidation reaction in an exhaust stream under net lean conditions. This catalyst has positive order kinetics with respect to CO for CO oxidation. Thus, as the concentration of CO in the exhaust is increased, the rate of this reaction is increased, resulting in a faster temperature rise over the catalyst.

This paper describes the development of new high performance three-way catalyst (TWC) formulations with improved activity and enhanced thermal stability. These new TWC formulations enable the converter to be fitted closer to the engine and allow this future legislation to be met with catalysts using PGM levels significantly lower than those currently being employed. The performance benefits of these advanced platinum- and palladium-based catalysts are demonstrated on a number of different vehicles after bench-engine ageing.

Enhancements in the thermal stability of three-way catalysts have been achieved by: 1) developing improved methods for the incorporation of ceria into catalyst formulations and 2) identifying a proprietary stabilizer which reduces the rate of ceria sintering at high temperature. Improvements in thermal stability are demonstrated by comparing the FTP and engine dynamometer performance of new formulations with a standard formulation after aging on several high temperature engine dynamometer cycles.

In the USA, hydrogen sulfide emissions from three-way catalytic converter-equipped automobiles are effectively suppressed by the addition of nickel to catalyst formulations. This approach is generally not utilized in catalyst formulations for Europe because of European concern about the health, safety and environmental issues surrounding the use of nickel. A modified form of iron oxide has been identified which suppresses hydrogen sulfide emissions from three-way catalysts. This suppression has been achieved without affecting the fresh or aged performance of the catalyst, a problem often encountered with other materials. The performance and durability of catalyst formulations incorporating the new material are demonstrated with a variety of aging and evaluation protocols.

In a collaborative programme, the effects of gasoline sulphur content on regulated emissions from three-way catalyst equipped vehicles have been studied. The programme evaluated the sulphur tolerance of three different catalyst formulations on the same range of vehicles. The catalyst chemistries were chosen to be representative of typical current formulations in different markets, as follows: 1. Platinum/Rhodium (Pt/Rh) 2. Platinum/Rhodium/Nickel (Pt/Rh/Ni) 3. Palladium/Rhodium (Pd/Rh) Each vehicle/catalyst combination was tested with fuels containing sulphur at nominal levels of 50, 250 and 450 ppm weight. All fuels were produced using the low sulphur fuel as a base and doping to 250 and 450 ppm S with a mixture of nine sulphur compounds, typical of those actually occurring in European gasolines. The results show clear differences between the magnitudes of the sulphur effect with different catalyst formulations.

One possibility to improve the fuel economy of SI-engines is to run the engine with a lean air-fuel-ratio (AFR). Hydrocarbon and carbon monoxide after-treatment has been proven under lean operation, but NOx-control remains a challenge to catalyst and car manufacturers. One strategy that is being considered is to run the engine lean with occasional operation at stoichiometry. This would be in conjunction with a three-way-catalyst (TWC) to achieve stoichiometric conversion of the three main pollutants in the normal way and a NOx trap. The NOx trap stores NOx under lean operation to be released and reduced under rich conditions. The trap also functions as a TWC and has good HC and CO conversion at both lean and stoichiometric AFR's. Under lean conditions NO is oxidised to NO2 on Pt which is then adsorbed on an oxide surface. Typical adsorbent materials include oxides of potassium, calcium, zirconium, strontium, lanthanum, cerium and barium.

A test programme has been conducted to study any potential long term effects of gasoline sulphur on catalyst performance, using a newly developed transient engine-bed ageing cycle. The ageing cycle, which was based on repeated European Extra Urban Drive Cycles, was chosen to ensure that the catalyst experienced a realistically wide range of temperatures and space velocities, together with transients, idle and periods of overrun. Two nominally identical platinum/rhodium catalysts (manufactured from the same batch) with matched lambda sensors, were aged for a period of 80,000 km each, one being aged using a gasoline containing 50 mg/kg (ppm wt) sulphur, the other being aged on the same fuel doped to 450 ppm wt S. The emissions performance of both catalysts was measured after 6,000, 40,000 and 80,000 km ageing, by fitting the catalysts to a test vehicle, and performing emissions tests over the European test cycle at both sulphur levels.

This paper describes the use of advanced three-way catalysts to meet future European and California low emissions legislation. Firstly, it describes the performance of these catalysts tested using the European Stage II test cycle and contrasts their emissions performance over the proposed European Stage III test. The future legislation requires fast catalyst light-off for the low emissions standards to be achieved, therefore the performance of close-coupled catalysts was investigated. The close-coupled catalyst systems gave very low emissions. Space constraints often preclude the use of large volume close-coupled catalysts, and the combination of a small starter catalyst with an underfloor catalyst was tested. This gave performance levels better than the close-coupled configuration. The effect of reducing the underfloor catalyst volume is also described. The work was carried out on a 1.2 litre European Vehicle, the conclusions were verified on a 1.6 litre European vehicle.

Recently, significantly more demanding emissions standards for the Mercosur region were proposed, and the intention is that these will be introduced in 2004 and 2008. This paper describes the development of new high performance three-way catalyst formulations for conventional gasoline/gasohol fueled engines that enables them to meet these stringent standards without increasing the content of platinum group metals above the levels currently employed. The performance benefits of these advanced platinum and palladium-based catalysts are demonstrated on both engine bench and vehicles.

With the advent of stricter vehicle emission standards, the improvement of three way catalyst performance and durability remains a pressing issue. A critical consideration in catalyst design is the potential for variations in fuel sulfur levels to have a significant impact on the ability to reach TLEV, LEV, and ULEV emission levels. As a result, a better understanding of the role of PGM composition in the interplay between thermal durability and sulfur tolerance is required. Three way catalysts representative of standard Pd-only, Pd/Rh and Pt/Rh formulations were studied over a variety of aging and evaluation conditions. The parameters investigated included aging temperature, air fuel ratio and sulfur level. Evaluations were performed on a 1994 TLEV vehicle using different sulfur level fuels. The effect of PGM loading was also included within the study.