Search Results

A simulation technology has been developed to enable prediction of galvanic corrosion in chassis parts where two different materials, iron and aluminum, come into contact with each other. When polarization curves representing a corrosive environment are input, this simulation technology calculates the corrosion current to flow and outputs the volume of aluminum corrosion to be formed near the iron-aluminum interface. The simulation makes it possible to predict the depth of corrosion that may occur in automobiles in the market.

Honda has developed an “Independent Left and Right Rear Toe Control System” that can achieve stable cornering performance and agile handling. We believe the issue that should be resolved in the next generation of ESC is the expansion of stability and agility into the general operation area. We examined how to accomplish this aim, and control of the independent rear toe angle was decided to be an appropriate method. In addition, a method for mounting the system without using a dedicated suspension was proposed. If left and right toe angles can be controlled independently, toe angle control and normal 4WS control become possible at the same time. In this paper, we will discuss the fundamental principle of independent toe angle control and the system configuration. Also, “INOMAMA Handling” (at driver's will) achieved by this system, as well as the fun and safe driving that are achieved as a result will be shown.

In this research, a three degree-of-freedom (DOF) rack-type electric-based power steering (EPS) model is developed. The model is coupled with a three DOF vehicle model and includes EPS maps as well as non-linear attributes such as vibration and friction characteristics of the steering system. The model is simulated using Matlab's Simulink. The vibration levels are quantified using on-vehicle straight-line test data where strain-gauge transducers are placed in the tie-rod ends. Full vehicle kinematic and compliance tests are used to verify the total steering system stiffness levels. Frequency response tests are used to adjust tire cornering stiffness levels as well as the tire dynamic characteristics such that vehicle static gain and yaw natural frequency are achieved. On-center discrete sinusoidal on-vehicle tests are used to further validate the model.

Recently vehicle development timeline is becoming shorter, so there is an urgent need to be able to develop vehicles with limited resources. This means the efficiency of the body structure development process must be improved. Specifically it is important to reduce the amount of design re-work required to meet performance targets as this can have a large influence on the body development time. In order to reduce the afore mentioned design re-work, we developed simple calculation models to apply a “V-Flow Development Process” to the preliminary stage design of the automobile body structure. The “V-Flow” advantages are as follows: (1) simple and easy to use, (2) defects are found at early stage, (3) avoids the downward flow of the defects. The advantage of preliminary stage design is that there is design flexibility since not many specifications have been determined yet.

The development and calibration of stress state-dependent failure criteria for advanced high-strength steel (AHSS) and aluminum alloys requires characterization under proportional loading conditions. Traditional tests to construct a forming limit diagram (FLD), such as Marciniak or Nakazima tests, are based upon identifying the onset of strain localization or a tensile instability (neck). However, the onset of localization is strongly dependent on the through-thickness strain gradient that can delay or suppress the formation of a tensile instability so that cracking may occur before localization. As a result, the material fracture limit becomes the effective forming limit in deformation modes with severe through-thickness strain gradients, and this is not considered in the traditional FLD. In this study, a novel bending test apparatus was developed based upon the VDA 238-100 specification to characterize fracture in plane strain bending using digital image correlation (DIC).

This study developed technology for simultaneously welding heterogeneous resin tubes in order to weld and integrate resin tubes with two different specifications (low temperature and high temperature). The aim of integration was cost and weight reduction. The cost reduction due to reducing the number of parts exceeded the increase in material cost due to a change to resin materials. Base material fracture of the resin tubes was set as the breaking format condition, and the welding parameters of the joint part rotations and the friction time between the joint part and the resin tubes were specified as the weld strength judgment standard. In addition, the fused thickness determined by observing the cross-section after welding was specified as the weld quality judgment standard. The range over which weld boundary peeling does not occur and weld strength is manifest was clarified by controlling the welding parameters and the fused thickness.

The SAE Fuel Cell Vehicle (FCV) Safety Working Group has been addressing FCV safety for over 9 years. The initial document, SAE J2578, was published in 2002. SAE J2578 has been valuable as a Recommended Practice for FCV development with regard to the identification of hazards and the definition of countermeasures to mitigate these hazards such that FCVs can be operated in the same manner as conventional gasoline internal combustion engine (ICE)-powered vehicles. SAE J2578 is currently being revised so that it will continue to be relevant as FCV development moves forward. For example, test methods were refined to verify the acceptability of hydrogen discharges when parking in residential garages and commercial structures and after crash tests prescribed by government regulation, and electrical requirements were updated to reflect the complexities of modern electrical circuits which interconnect both AC and DC circuits to improve efficiency and reduce cost.

The SAE FCV Safety Working Group has been addressing fuel cell vehicle (FCV) safety for over 8 years. The initial document, SAE J2578, was published in 2002. SAE J2578 has been valuable to FCV development with regard to the identification of hazards and the definition of countermeasures to mitigate these hazards such that FCVs can be operated in the same manner as conventional gasoline internal combustion engine (ICE)-powered vehicles. J2578 is currently being updated to clarify and update requirements so that it will continue to be relevant and useful in the future. An update to SAE J1766 for post-crash electrical safety was also published to reflect unique aspects of FCVs and to harmonize electrical requirements with international standards. In addition to revising SAE J2578 and J1766, the Working Group is also developing a new Technical Information Report (TIR) for vehicular hydrogen systems (SAE J2579).

The SAE Fuel Cell Vehicle (FCV) Safety Working Group has been addressing FCV safety for over 10 years. The initial document, SAE J2578, was published in 2002. SAE J2578 has been valuable as a Recommended Practice for FCV development with regard to the identification of hazards associated with the integration of hydrogen and electrical systems onto the vehicle and the definition of countermeasures to mitigate these hazards such that FCVs can be operated in the same manner as conventional gasoline internal combustion engine (ICE)-powered vehicles. An update to SAE J1766 for post-crash electrical safety was also published in 2008 to reflect unique aspects of FCVs and to harmonize electrical requirements with international standards. In addition to SAE J2578 and J1766, the SAE FCV Safety Working Group also developed a Technical Information Report (TIR) for vehicular hydrogen systems (SAE J2579).

Three-dimensional transient simulations using KIVA-3V were conducted on a 4-stroke high-compression ratio, methanol-fueled, direct-injection (DI) engine. The engine had two intake ports that were designed to impart a swirling motion to the intake air. In some cases, the intake system was modified, by decreasing the ports diameter in order to increase the swirl ratio. To investigate the effect of adding shrouds to the intake valves on swirl, two sets of intake valves were considered; the first set consisted of conventional valves, and the second set of valves had back shrouds to restrict airflow from the backside of the valves. In addition, the effect of using one or two intake ports on swirl generation was determined by blocking one of the ports.

Numerical simulations of lean Methanol combustion in a four-stroke internal combustion engine were conducted on a high-compression ratio engine. The engine had a removable integral injector ignition source insert that allowed changing the head dome volume, and the location of the spark plug relative to the fuel injector. It had two intake valves and two exhaust ports. The intake ports were designed so the airflow into the engine exhibited no tumble or swirl motions in the cylinder. Three different engine configurations were considered: One configuration had a flat head and piston, and the other two had a hemispherical combustion chamber in the cylinder head and a hemispherical bowl in the piston, with different volumes. The relative equivalence ratio (Lambda), injection timing and ignition timing were varied to determine the operating range for each configuration. Lambda (λ) values from 1.5 to 2.75 were considered.

A numerical study on the combustion of Methanol in a directly injected (DI) engine was conducted. The study considers the effect of the bowl-in-piston (BIP) geometry, swirl ratio (SR), and relative equivalence ratio (λ), on flame propagation and burn rate of Methanol in a 4-stroke engine. Ignition-assist in this engine was accomplished by a spark plug system. Numerical simulations of two different BIP geometries were considered. Combustion characteristics of Methanol under swirl and no-swirl conditions were investigated. In addition, the amount of injected fuel was varied in order to determine the effect of stoichiometry on combustion. Only the compression and expansion strokes were simulated. The results show that fuel-air mixing, combustion, and flame propagation was significantly enhanced when swirl was turned on. This resulted in a higher peak pressure in the cylinder, and more heat loss through the cylinder walls.

Collection of diesel exhaust using the Tapered Element Oscillating Microbalance (TEOM) instrument was investigated as an alternative to the traditional method of filter weighing for particulate matter mass determination. Such an approach, if successful, would eliminate considerable manual labor involved in weighing, as well as the delay of hours or days before final results were known. To avoid known artifacts in the second-by-second mode of operation, the TEOM was used in a phase-by-phase mode and was equilibrated with air of constant temperature and humidity before each measurement. Electrically operated valves were used to automate the equilibration and measurement process. The study also included a comparison between two types of TEOM filter - an older type and a new one designed by the TEOM manufacturer for more uniform flow and less flexing. Best results were obtained with the TEOM using the new filter under no-flow conditions.

The CAE method to predict the vibration transfer function of the hydraulic engine mount on a vehicle with sufficient precision and calculation time without prototype cars was developed. The transfer function is given in the following steps. First, rubber deformation form under the power train weight loaded must be predicted. It’s obtained by using a reduction model of an engine mount, as a unit, which doesn’t have its fluid sealed inside, with the technique to get the static spring characteristics in a non-linear relationship. Second, Young’s modulus and structural damping coefficient for the deformed rubber must be given. As for these characteristics, ignoring the relations between these values and strain, the constant values are used. This considerably reduces computation time and model size. Next, the reduction model and the fluid model have must be combined to express actual product. In this step, coupled analysis for fluid and structure is used.

Practical evaluation and reduction of edge cracking are two challenging issues in stamping AHSS for automotive body structures. In this paper, the effects of the shear clearance and shear rake angle on edge cracking were investigated with three different grades of AHSS; TRIP780, DP 980, and DP 1180. Five different shear clearances, between 5% and 25% of material thickness, were applied to the flexible shearing machine to generate samples for the half specimen dome test (HSDT). The shear loads and the shear edge quality were thoroughly characterized and compared. The HSDT created the edge forming limits as compared to the base material forming limit diagram. The load-displacement curve was acquired by the load-cell and the strain distribution was measured using a digital image correlation (DIC) system during the dome test.

A high-speed/high-resolution imaging technique and analysis were applied to study fuel injector spray timed evolution in ambient air and in a motored single-cylinder engine. Alcohol fuel was injected from a mid-pressure injection system into the engine cylinder at shaft speed of 1,000 rpm. The fuel injection system with various nozzles was designed for use in the EPA/NVFEL program to develop clean and efficient engines that use alternative fuels. A 15W copper vapor laser with a fiber optic delivery system synchronized with a high-speed drum streak camera was utilized to expose films at 5,000 frames per second (fps). The spray characteristics were investigated at 15.0 MPa injection pressure and injection duration range of 3-5 ms. A sequence of successive frames was selected from the films to examine the influence of the injector parameters and the valve lift on the atomization process. The spray penetration was quantified by analyzing the high-speed films.

Three-dimensional numerical simulations of a diesel-fueled engine with a pre-chamber located in the cylinder head and a bowl in the piston were performed. The study considers the effect of diesel combustion in the pre-chamber on turbulence generation and hence fuel-air mixing and combustion in the piston-bowl. Diesel fuel was injected directly into the pre-chamber and the piston bowl at different times. In order to better determine the effect of pre-chamber combustion on the main chamber combustion, various pre-chamber injection timings were considered. The results show that pre-chamber combustion caused the average cylinder pressure to increase by up to 20% in some cases.

This paper presents a review of the regulatory, environmental, and health issues surrounding the use of halons as a fire suppressant and a summary of the recently completed Racecar Fire Suppressant Exposure Study by ICF Consulting, Inc., under contract with the U.S. Environmental Protection Agency (EPA) (U.S. EPA, 2004a). In 2003 the EPA learned that the SFI Foundation Inc., the organization responsible for developing safety regulations and testing requirements for numerous Performance Racing Industry (PRI) sanctioning bodies, was revising its Quality Assurance Specification for On Board Fire Suppression Systems (SFI Specification 17.1). The previous Specification 17.1 required either halon 1211 or halon 1301 to be used in these systems. Halons are ozone-depleting substances (ODS) widely used in fire protection applications and whose production and use are controlled under the Montreal Protocol and the Clean Air Act (CAA).

Automotive manufacturers across the world have experienced the saturation of demand in the mature markets. Foraying into the emerging markets of India and China brings a mix of opportunities and challenges. These economies with 15%+ rising consumer demand, 7%+ rise in per-capita income and a passenger car density less than 1/8 of mature markets, hold promise of sustaining double-digit growth of vehicle sales. But the challenges are immense. Ultra-low margins of OEMs, lack of transportation infrastructure, Low level of maturity of funding operations, fragmented demand, import restrictions and mandatory export obligations pose serious constraints to non-linear growth. HONDA (Honda Siel Cars India Limited), a subsidiary of Honda Motor Corporation, Japan has developed the next generation supply chain with a strategy cognizant of the global opportunities and the local limitations which such emerging economies present.

This paper presents results from a study of the particle size distributions emitted by a heavy-duty diesel engine equipped with a common-rail fuel injection system. The study focused on two key sampling and engine operating variables: dilution ratio and fuel injection pressure. Results show that the number mean diameter of the particle size distributions decreased with increasing dilution ratios. Also, the total number concentration of particles did not change with different dilution ratios. In addition, it was found that fuel injection pressures affected the size distribution of the particles sampled. Under some engine operating conditions increasing the fuel injection pressure resulted in an increased number of nuclei mode particles.