Search Results

Recent field data have shown that the occupant protection in vehicle rear seats failed to keep pace with advances in the front seats likely due to the lack of advanced safety technologies. The objective of this study was to optimize advanced restraint systems for protecting rear seat occupants with a range of body sizes under different frontal crash pulses. Three series of sled tests (baseline tests, advanced restraint trial tests, and final tests), MADYMO model validations against a subset of the sled tests, and design optimizations using the validated models were conducted to investigate rear seat occupant protection with 4 Anthropomorphic Test Devices (ATDs) and 2 crash pulses.

As software (SW) becomes more and more an important aspect of embedded system development, project schedules are requiring the earlier development of software simultaneously with hardware (HW). In addition, verification has increasingly challenged the design of complex mixed-signal SoC products. This is exacerbated for automotive safety critical SoC products with a high number of analogue interfaces (sensors and actuators) to the physical components such as an airbag SoC chipset. Generally, it is widely accepted that verification accounts for around 70% of the total SoC development. Since integration of HW and SW is the most crucial step in embedded system development, the sooner it is done, the sooner verification can begin. As such, any approaches which could allow verification and integration of HW/SW to be deployed earlier in the development process and help to decrease verification effort, (e.g.: accelerate verification runs) are of extreme interest.

In the automotive industry, FMEA occurrence ranking is made to a standard such as SAE J1739. The SAE J1739 standard, as does other comparative standards, provides numerical probability criteria to aid ranking. Problems arise when the part or system under analysis is new, and there is no field data to estimate the probability of failure occurrence. Attempts to use qualitative verbal criteria or to go by the “feel” often result in inconsistency or large variability across and within FMEA projects. This paper presents a case study in which this problem was solved by the development of a tool that enables consistent - and efficient - FMEA occurrence rankings. The tool takes input from the user in the form of multiple-choice answers and calculates the final solution.

Computer Simulation was extensively utilized in the design and development of the Active Roll Control (ARC) system on LandRover 4X4 vehicle. An ADAMS model was developed integrating the electronic controller, hydraulic activation and vehicle model into one system of various degrees of complexity. Simulation results not only correlated well with vehicle test results, but also provided invaluable design guidelines crucial for solving key stability issues and successful product launch.

The ISO TC22/SWG2 - Brake Lining Committee established a task force to determine and analyze root causes for variability during dynamometer brake performance testing. SAE paper 2010-01-1697 “Brake Dynamometer Test Variability - Analysis of Root Causes” [1] presents the findings from the phases 1 and 2 of the “Test Variability Project.” The task force was created to address the issue of test variability and to establish possible ways to improve test-to-test and lab-to-lab correlation. This paper presents the findings from phase 3 of this effort-description of factors influencing test variability based on DOE study. This phase concentrated on both qualitative and quantitative description of the factors influencing friction coefficient measurements during dynamometer testing.

Two methods are allowed in ISO 26262-5 for hardware analysis of random hardware failures. The 1st method is called “Evaluation of Probabilistic Metric for random Hardware Failures”. The 2nd method is called “Evaluation of each cause of safety goal violation”. Advantages of the 2nd method during development of ASIL D Generation 3 Electric Power Steering are presented in this paper. A reliability analysis is one of the important prerequisite for the hardware analysis and this paper shows the best practice for hardware part failure rate estimation using industry standards such as IEC TR 62380. The equally important focus is on a diagnostic coverage of each safety mechanism with respect to residual faults and with respect to relevant dual/latent point faults because any safety design can either benefit from low failure rates or from high diagnostic coverage of safety mechanism to mitigate faults. FMEA is highly recommended by ISO 26262-5 as a part of hardware analysis.

While much research has focused on improving terrain mobility, energy and fuel efficiency of terrain trucks, only a limited amount of investigation has gone into analysis of power distribution between the driving wheels. Distribution of power among the driving wheels has been shown to have a significant effect on vehicle operating characteristics for a given set of operating conditions and total power supplied to the wheels. Wheel power distribution is largely a function of the design of the driveline power dividing units (PDUs). In this paper, 6×6/6×4 terrain truck models are analyzed with the focus on various combinations of PDUs and suspension systems. While these models were found to have some common features, they demonstrate several different approaches to driveline system design.

Frontal crashes (11-1 o'clock) were reviewed from the National Accident Severity Study file (NASS) for years 1980-87. Adult drivers and front right passengers, with lower extremity injuries of the pelvis, thigh, knee, leg or ankle/foot were reviewed. Analysis of age differences, injury contacts, and effectiveness of the 3-point restraint system were studied. Unrestrained drivers have a higher frequency of knee injuries than passengers, fewer leg injuries than passengers and both have the same frequency of ankle/foot injuries. Older unbelted drivers have more injuries to the pelvis, leg, and ankle/foot region than do young drivers. Passengers have more leg injuries. The instrument panel is the major contact for most of the lower extremity injuries. Lap/shoulder belts significantly reduce lower extremity injury frequency.

Driver assistance systems are incorporating more and more advanced safety functions. As these functions have to react quickly and reliably in emergency situations with a false alarm rate close to zero a high integrity of the environmental perception is required. This elevated level of signal integrity can be achieved by data fusion, where the information of several, in general heterogeneous sensors is combined to obtain a better model of the environment in terms of accuracy, object integrity, object identity, etc. As an example, we demonstrate the power of sensor fusion by an automatic emergency brake (AEB) system whose environmental perception is based upon a video camera and a radar sensor. In particular we discuss the improvement of kinematic attributes such as object lateral distance as well as the object's confidence or probability of existence.

The factors that influence airbag-induced upper-extremity injuries sustained by drivers were investigated in this study. Seven unembalmed human cadavers were used in nineteen direct-forearm-interaction static deployments. A single horizontal-tear-seam airbag module and two different inflators were used. Spacing between the instrumented forearm and the airbag module was varied from 10 cm to direct contact in some tests. Forearm-bone instrumentation included triaxial accelerometry, crack detection gages, and film targets. Internal airbag pressure was also measured. The observed injuries were largely transverse, oblique, and wedge fractures of the ulna or radius, or both, similar to those reported in field investigations. Tears of the elbow joint capsule were also found, both with and without fracture of the forearm.

SAE Recommended Practice J941 describes the eyellipse, a statistical representation of driver eye locations, that is used to facilitate design decisions regarding vehicle interiors, including the display locations, mirror placement, and headspace requirements. Eye-position data collected recently at University of Michigan Transportation Research Institute (UMTRI) suggest that the SAE J941 practice could be improved. SAE J941 currently uses the SgRP location, seat-track travel (L23), and design seatback angle (L40) as inputs to the eyellipse model. However, UMTRI data show that the characteristics of empirical eyellipses can be predicted more accurately using seat height, steering-wheel position, and seat-track rise. A series of UMTRI studies collected eye-location data from groups of 50 to 120 drivers with statures spanning over 97 percent of the U.S. population. Data were collected in thirty-three vehicles that represent a wide range of vehicle geometry.

Standing reach envelopes are important tools for the design of industrial and vehicle environments. Previous work in this area has focussed on manikin-based (where a few manikins are used to simulate individuals reaching within the region of interest) and population-based (where data are gathered on many individuals reaching in a constrained environment) approaches. Each of these methods has merits and shortfalls. The current work bridges the manikin- and population-based approaches to assessing reach by creating population models using kinematic simulation techniques driven by anthropometric data. The approach takes into account body dimensions, balance, and postural cost to create continuous models that can be used to assess designs with respect to both maximal and submaximal reaches. Cost is quantified as the degree to which the torso is involved in the reach, since the inclination of the torso is a good measure of lower-back load and may be related to subjective reach difficulty.

Four unembalmed human cadavers were used in eight direct-forearm-airbag-interaction static deployments to assess the relative aggressivity of two different airbag modules. Instrumentation of the forearm bones included triaxial accelerometry, crack detection gages, and film targets. The forearm-fracture predictors, peak and average distal forearm speed (PDFS and ADFS), were evaluated and compared to the incidence of transverse, oblique, and wedge fractures of the radius and ulna. Internal-airbag pressure and axial column loads were also measured. The results of this study support the use of PDFS or ADFS for the prediction of airbag-induced upper-extremity fractures. The results also suggest that there is no direct relationship between internal-airbag pressure and forearm fracture. The less-aggressive system (LAS) examined in this study produced half the number of forearm fracture as the more-aggressive system (MAS), yet exhibited a more aggressive internal-pressure performance.

The ease of getting into and out of passenger cars and light trucks is a critical component of customer acceptance and product differentiation. In commercial vehicles, the health and safety of drivers is affected by the design of the steps and handholds they use to get into and out of the cab. Ingress/egress assessment appears to represent a substantial application opportunity for digital human models. The complexity of the design space and the range of possible biomechanical and subjective measures of interest mean that developing useful empirical models is difficult, requiring large-scale subject testing with physical mockups. Yet, ingress and egress motions are complex and strongly affected by the geometric constraints and driver attributes, posing substantial challenges in creating meaningful simulations using figure models.

A new system reliability allocation methodology was applied on a steering product. The methodology makes use of design failure modes and effects analysis (DFMEA) and allows the allocation percentages to reflect differences in the criticality levels of the subsystems or components. The methodology was applied in conjunction with system reliability target setting. The paper first explores existing reliability allocation methods. It then introduces the new methodology. Finally, a real-life case is presented to show how the methodology was adopted and how and why it was modified. The approach presented here is one more way to make full use of the analytical efforts that have gone into the DFMEA.

This paper reports the progress that has been made to date on a research program that has as its focus to describe the mechanism of metal pick-up generation on passenger car disc brake pads in correlation with deep rotor scoring. In contrast to other existing generation theories, the new investigation considers other aspects of the initial onset of the metal pick-up.

In the past, each noise shim supplier had its own specifications to describe the properties of their noise shims (often also called as shim or damping shim). Due to that, it was difficult to compare the physical properties of noise shims from different suppliers. The main task was to define common specifications for daily quality/development tests. Traceability in prototype status and production was introduced establishing a clear declaration of noise shim deliveries with batch no. and “use by” date. Harmonization was created through standardized tests and procedures. In addition, a common noise shim database for all noise shim manufacturers was established. A more realistic compressibility test was developed to estimate the additional compressibility of noise shims based on bare pads under cold and hot conditions. These values are important to describe the axial decoupling at low pressure and the maximal displacement at high forces.

This study outlines a protocol for image data collection acquired from human volunteers. The data set will serve as the foundation of a consolidated effort to develop the next generation full-body Finite Element Analysis (FEA) models for injury prediction and prevention. The geometry of these models will be based off the anatomy of four individuals meeting extensive prescreening requirements and representing the 5th and 50th percentile female, and the 50th and 95th percentile male. Target values for anthropometry are determined by literature sources. Because of the relative strengths of various modalities commonly in use today in the clinical and engineering worlds, a multi-modality approach is outlined. This approach involves the use of Computed Tomography (CT), upright and closed-bore Magnetic Resonance Imaging (MRI), and external anthropometric measurements.

One of the most important means used for suppressing squeal noise in disc brakes is the application of shims on the pad backplates. In many cases this proves a very efficient tool depending on the type of shim applied in the specific cases. Building up knowledge on the effects of shims have been ongoing for several years, and measuring the important parameters characterizing the shims is crucial for understanding how to develop and implement the shims in an optimal way. Several methods are described in literature for measuring the constrained layer damping effect and one method is described for direct measurement of the shear stiffness and shear damping properties. However, up to now no method has been available that can measure and characterize the normal stiffness and damping properties of shims. This is one of the most important properties of shims as it controls the de-coupling effect in the direction of the normal forces.

Traditionally, reliability of a product is estimated or predicted using known constant failure rates of components or assumed probability distributions. There can be significant differences between predictions and actual product performance. In this paper, an alternative reliability prediction approach is developed. The reliability of a system is estimated with upper and lower boundaries.