Search Results

Standard

TEST METHODS FOR METRIC THREADED FASTENERS

1978-03-01

HISTORICAL

J1216_197803

This standard establishes procedures for conducting tests to determine the mechanical properties of externally and internally threaded fasteners.

Standard

Torque-Tension Tightening for Metric Series Fasteners

2022-03-29

CURRENT

J1701M_202203

This SAE Information Report is provided as an advisory guide. Individual application discretion is recommended. The content has been presented as accurately as possible, but responsibility for its application lies with the user. The document covers a number of the variables in the torque-tension relationship: friction, materials, temperature, humidity, fastener and mating part finishes, surfaces, and the kind of tightening tools or equipment used. Also described in this document is the torque management required to achieve satisfactory fastened joint tightening. This guide is limited in application to clearance fit threads, such as the common 6g/6H class of fit. Other thread types including interference fit, mechanical locking, prevailing torque, or forms other than ISO-metric may apply to some aspects of this standard but are not specifically covered.

Standard

STEEL STAMPED NUTS OF ONE PITCH THREAD DESIGN—METRIC SERIES

1996-08-01

HISTORICAL

J1053M_199608

Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of stamped nuts of one pitch thread design recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw or unthreaded stud is considered adequate for the application. For the inch equivalent of this document, see SAE J1053.

Standard

Holes in Bolt and Screw Shanks and Slots in Nuts for Cotter Pins

2016-11-18

CURRENT

J485_201611

SAE J485 specifies the recommended nominal diameters and locations of holes in bolt or screw shanks, and nominal widths and depths of slots in nuts, for use with the recommended sizes of inch-series cotter pins, as shown in Table 1.

Standard

Hexagon High Nuts

2016-11-18

CURRENT

J482_201611

Included herein are the detailed general and dimensional specifications applicable to high hex nuts. All general specifications not shown here shall conform with those applicable to hex thick nuts and hex thick slotted nuts appearing in ASME B18.2.2. High hex nuts are primarily intended for use in automotive and other ground-based vehicles and industrial equipment where a long length of hexagon is required for wrenching purposes.

Standard

CROWN (BLIND, ACORN) NUTS

1993-09-01

HISTORICAL

J483_199309

Included in this SAE Recommended Practice are complete general and dimensional data for the high and low types of crown nuts recognized as SAE Standard. These nuts are primarily intended for application in automotive and other ground-based motor vehicles and industrial equipment to provide an ornamental or protective closure over end of bolts, studs, or screws.

Standard

CROWN (BLIND, ACORN) NUTS

1998-05-01

HISTORICAL

J483_199805

Included in this SAE Recommended Practice are complete general and dimensional data for the high and low types of crown nuts recognized as SAE Standard. These nuts are primarily intended for application in automotive and other ground-based motor vehicles and industrial equipment to provide an ornamental or protective closure over end of bolts, studs, or screws.

Standard

High and Low Crown (Blind, Acorn) Hex Nuts

2006-03-09

HISTORICAL

J483_200603

Included in this SAE Recommended Practice are complete general and dimensional data for the high and low types of crown nuts recognized as SAE Standard. These nuts are primarily intended for application in automotive and other ground-based motor vehicles and industrial equipment to provide an ornamental or protective closure over end of bolts, studs, or screws.

Standard

HOLES IN BOLT AND SCREW SHANKS AND SLOTS IN NUTS FOR COTTER PINS

1998-05-01

HISTORICAL

J485_199805

SAE J485 specifies the recommended nominal diameters and locations of holes in bolt or screw shanks, and nominal widths and depths of slots in nuts, for use with the recommended sizes of inch-series cotter pins, as shown in Table 1.

Standard

Holes in Bolt and Screw Shanks and Slots in Nuts for Cotter Pins

2013-04-16

HISTORICAL

J485_201304

SAE J485 specifies the recommended nominal diameters and locations of holes in bolt or screw shanks, and nominal widths and depths of slots in nuts, for use with the recommended sizes of inch-series cotter pins, as shown in Table 1.

Standard

HEXAGON HIGH NUTS

1998-05-01

HISTORICAL

J482_199805

Included herein are the detailed general and dimensional specifications applicable to high hex nuts. All general specifications not shown here shall conform with those applicable to hex thick nuts and hex thick slotted nuts appearing in ASME B18.2.2. High hex nuts are primarily intended for use in automotive and other ground-based vehicles and industrial equipment where a long length of hexagon is required for wrenching purposes.

Standard

Hexagon High Nuts

2006-04-17

HISTORICAL

J482_200604

Included herein are the detailed general and dimensional specifications applicable to high hex nuts. All general specifications not shown here shall conform with those applicable to hex thick nuts and hex thick slotted nuts appearing in ASME B18.2.2. High hex nuts are primarily intended for use in automotive and other ground-based vehicles and industrial equipment where a long length of hexagon is required for wrenching purposes.

Standard

THREAD ROLLING SCREWS

1972-07-01

HISTORICAL

J81_197207

This standard covers requirements for thread rolling screws suitable for use in general engineering applications. (It is intended that “thread rolling” screws have performance capabilities beyond those normally expected of other standard types of tapping screws.) Note: The performance requirements covered in this standard apply only to the combination of laboratory conditions described in the testing procedures. If other conditions are encountered in an actual service application (such as different materials, thicknesses, hole sizes, etc.), values shown herein for drive torque, torque-to-clamp load, and proof torque may require adjustment.

Standard

THREAD ROLLING SCREWS

1979-06-01

HISTORICAL

J81_197906

This standard covers requirements for thread rolling screws suitable for use in general engineering applications. (It is intended that "thread rolling" screws have performance capabilities beyond those normally expected of other standard types of tapping screws.) Note: The performance requirements covered in this standard apply only to the combination of laboratory conditions described in the testing procedures. If other conditions are encountered in an actual service application (such as different materials, thicknesses, hole sizes, etc.), values shown herein for drive torque, torque-to-clamp load, and proof torque may require adjustment.

Standard

Spring Nuts

1998-05-01

HISTORICAL

J891_199805

Included herein are complete general and dimensional specifications for metric and inch types of spring nuts recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw is considered adequate for the application. It should be noted that spring nuts having other configurations, dimensions, provisions for ground, etc., are available and manufacturers should be consulted.

Standard

Spring Nuts

2004-10-04

HISTORICAL

J891_200410

Included herein are complete general and dimensional specifications for metric and inch types of spring nuts recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw is considered adequate for the application. It should be noted that spring nuts having other configurations, dimensions, provisions for ground, etc., are available and manufacturers should be consulted.

Standard

SPRING NUTS

1964-08-01

HISTORICAL

J891_196408

Standard

SPRING NUTS

1993-06-14

HISTORICAL

J891_199306

Included herein are complete general and dimensional specifications for metric and inch types of spring nuts recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw is considered adequate for the application. It should be noted that spring nuts having other configurations, dimensions, provisions for ground, etc., are available and manufacturers should be consulted.

Standard

PUSH-ON SPRING NUTS METRIC SERIES—GENERAL SPECIFICATIONS

1996-08-01

HISTORICAL

J892M_199608

Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of steel stamped Push-On Spring Nuts recognized as SAE standard. These nuts are intended for general use where the engagement on the mating metal or plastic studs and in some cases screw bolt threads is considered adequate for the fastening joint application. It should be noted that Push-On Spring Nuts having other characteristics and configurations are available and manufacturers should be consulted. For the inch equivalent of this document, see SAE J892.

Standard

PUSH-ON SPRING NUTS INCH SERIES—GENERAL SPECIFICATIONS

1996-08-01

HISTORICAL

J892_199608

Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of steel stamped Push-On Spring Nuts recognized as SAE standard. These nuts are intended for general use where the engagement on the mating metal or plastic studs and in some cases screw or bolt threads is considered adequate for the fastening joint application. It should be noted that Push-On Spring Nuts having other characteristics and configurations are available and manufacturers should be consulted. For the metric equivalent of this document, see SAE J892M.