Search Results

This method of gaging alignment of nut slots allows equal variations for location of the cotter pin hole in the bolt and location of slots in the nut. To inspect the nut, the slotted gage is inserted through the nut hole from the bearing surface of the nut. Alignment of slots is considered satisfactory if the gage pin can be slipped into the gage and nut slots without interference.

Round head bolts are made in two body styles: (a) A full size body, with a maximum diameter somewhat greater than the nominal diameter (not an SAE Standard except for ribbed neck bolts, Table 3); and (b) an undersize body, with a minimum diameter approximating the pitch diameter of the thread and a maximum diameter never exceeding nominal (SAE standard for all types except ribbed neck bolts). The body diameter of either style may be exceeded by a reasonable swelling or fin under the head, or under corners of the square necks, to the extent that serviceability is not affected.

The 12 papers in this techncial paper collection represent research in the areas of welding, riveting, joining, and fastening for automotive applications. Papers focus on the recent advances in the process optimization, analytical solution, numerical modeling, response evaluation as well as static and dynamic testing of traditional resistance spot welds, gas metal arc welds, friction stir spot welds, laser welds, rivets, mounts, adhesives, and fasteners.

The three major challenges in the power electronics in hybrid and electric vehicles are: System cost, power density and reliability. High temperature power device and packaging technologies increases the power density and reliability while reducing system cost. Advanced Silicon devices with synthesized high-temperature packaging technologies can achieve junction temperature as high as 200C (compared to the present limitation of 150C) eliminating the need for a low-temperature radiator and therefore these devices reduces the system cost. The silicon area needed for a power inverter with high junction temperature capability can be reduced by more than 50 - 75% thereby significantly reducing the packaging space and power device and package cost. Smaller packaging space is highly desired since multiple vehicle platforms can share the same design and therefore reducing the cost further due to economies of scale.

This session covers topics regarding new CI and SI engines and components. This includes analytical, experimental, and computational studies covering hardware development as well as design and analysis techniques. Presenter Sung Hoon Lee, Hyundai Motor Co.

FutureSteelVehicle's (FSV) objective is to develop detailed design concepts for a radically different steel body structure for a compact Battery Electric Vehicle (BEV). It also will identify structure changes to accommodate larger Plug-In Hybrid (PHEV) and Fuel Cell (FCEV) vehicle variants. The presentation will demonstrate seven optimized structural sub-systems that contribute to the program's 35 percent mass reduction goals and meet its safety and life cycle emissions targets. It will explain the advanced design optimization process used and the resulting aggressive steel concepts. Presenter Jody R. Shaw, US Steel

Presentation will concentrate on a brief overview of SAE International including history, international focus and SAE electro-mobility ground vehicle standards development activities. The new era of mobility and the driving forces behind it including converging technologies and today�s drive toward �green� will be discussed. Also, standards and technology enablers for vehicle electrification including, the global landscape for EV charging standards and next generation charging method approaches will be reviewed. Additionally, an overview of SAE global EV Battery Standards and activities including industry/government collaborative efforts to develop lithium ion rechargeable energy storage system safety standards will be provided. Presenter Keith Wilson, SAE International

The grant application process can be overwhelming. With several years of incentive program guidance, sustainable transportation services and strategic market assessment expertise, Emisstar LLC has the grant process down to a science. During this presentation, Tiffany Hollon will share her experience as an Emisstar staff member to guide you through the primary steps, preparation and follow-up for a typical grant application. Real-life examples and an application walk-through will demystify the most complicated parts of the process. Throughout the discussion, helpful tips persuasion strategies will be shared to help make your application stand apart from the crowd. Presenter Tiffany Hollon, Emisstar LLC

Low Voltage Electric Drives are becoming very attractive for various applications in the Turf, Construction and Agricultural products being engineered today. Determining what the Customer Support Requirements are for Maintenance and Repair for the Life Cycle of the products is critical to the initial design process. Presenter Russell Christ

Optical fiber has begun replacing copper in avionic networks. So far, however, it has been mainly restricted to non-critical applications (video transmission to the flight deck, IFE?). In order to take advantage of the high-bandwidth, low weight, no EMI properties of optical fibers in all data transmission networks, it will be necessary to improve the testing. One part of the puzzle, which is still missing, is the self-test button: the possibility to check the network and detect potential failures before they occur. The typical testing tool of a technician involved in optical fiber cables is the ?light source ? optical power meter? pair. With this tool, one can measure the insertion loss of the fiber link. A second important parameter, the return loss at each optical connector, is not analysed. In addition, this is only a global measurement, which does not allow the detection of possible weak points.

The use of Engine Health Management (EHM) systems has been growing steadily in both the civilian and the military aerospace sectors. Barring a few notable exceptions (such as certain temperature and thrust margin monitoring) regulatory authorities around the world have not required these systems to be certified in any way. This is changing rapidly. New airframes and engines are increasingly being designed with the assumption that EHM will be an integral part of the way customers will operate these assets. This leads to a need for better guidelines on how such systems should be certified. The SAE E-32 committee on Propulsion System Health Monitoring is leading an industry-wide effort to develop a set of guidelines for certifying EHM systems.

The System Architecture Virtual Integration (SAVI) program is a collaboration of industry, government, and academic organizations within the Aerospace Vehicle System Institute (AVSI) with the goal of structuring a new integration process that relies on a single-truth architectural framework. The SAVI approach of Integrate, then Build provides a modern distributed development environment which arrests the propagation of requirements errors through the development life cycle. It does so by capturing design assumptions and shared properties of the system design in an authoritative, annotated architectural model. This reference model provides a common, analyzable framework for confirming that system requirements remain complete, consistent, and correct at all levels of system decomposition. Core concepts of SAVI include extensive use of model-based system engineering tools and use of a single-truth reference architectural model.

Up to now, the reliability achieved by COTS components was largely sufficient for avionics, in terms of failure rate as well as time to failure. With the implementation of new and more integrated technologies (90 nm node, 65 nm and below), the question has arisen of the impact of the new technologies on reliability. It has been stated that the lifetime of these new technologies might decrease. The drift is expected to be technology dependent: integration, technology node, materials, elementary structure choices and process pay a key role. Figures have been published, which gives smaller lifetime than the 30 years generally required for avionics. This would of course impact not only the reliability, but also the maintenance of COTS-based avionics. Hence a new policy should be defined for the whole COTS supply chain. Faced with these impending risks, different methodologies have been developed.

This article characterizes the special features of drilling of CFRP/Titanium and -Aluminium stacks. Simplified theoretic models will show how CFRP/Titanium stacks should be machined without scratches and burn marks contacting carbon. Low axial forces and smart chip removal technology are the main characteristics of the drilling tool technology, optimized to reach H8 quality in one shot operation. Presenter Peter Mueller-Hummel, Cutting Tools Inc.

The aerospace industry has long sought a solution for storing maintenance history information directly on aircraft parts. In 2005 leading airframe manufacturers determined that passive Radio Frequency Identification (RFID) technology presented a unique opportunity to address this industry need. Through the efforts of the Air Transport Association (ATA) RFID on Parts Committee and SAE International testing standards and data specifications are in place to support the broad adoption of passive RFID for storing parts history information directly on aircraft parts. The primary focus of the paper will be on the SAE AS-5678 environmental testing standard for passive RFID tags intended for aircraft use. Detail will be provided to help aerospace manufacturers understand their role and responsibilities for current programs and understand how this may impact their parts certification process.

In any new aircraft development program there are many important design decisions that determine profitability potential. The key to making new aircraft profitable is to design features that will command more money than the cost to provide them within the market's ability to absorb them. The business model in this paper shows how to predict or find: 1) the costs to provide various aircraft features; 2) the values that aircraft buyers place on these features; 3) the amount of money that buyers have to commit to them, 4) the open spaces in the market in which to place new designs and 5) the predicted profits from new designs. In this process, this paper extends previous work on the law of value and demand, which states that attributes determine value; value determines price; and that price determines demand. This four-dimensional, non-negative system hosts a business model that describes the features needed to enable aircraft designs to go from concepts to profitable assembly lines.

High Speed Machining of CFRP Parts Investigation of the influence of new geometries, cutting datas and coolant capabilities on the surface finish of CFRP parts. State of the art: Different CFRP grades and machining conditions make geometry adjustments to the tool necessary. Mechanical failures through machining operations can be avoided in most of the cases. New unidirectional CFRP grades and dry machining processes again lead to machining problems. This study investigates new geometries to avoid heat damage with dry maching and air coolant in case of unidirectional CFRP. With help of a thermo camera and the surface investigation with a scanning electron microscope, heat damage can be analysed and therefore new geometries can be developed and tested. Target is to develop a new multi purpose CFRP geometry to meet the requirements of the future. The reduction of different geometries used leads to major cost savings. Presenter Ingo von Puttkamer, Guhring oHG