Search Results

Homogeneous charge compression ignition (HCCI), has the potential to improve the fuel economy and to reduce NOx emission significantly. Spark plug in SI engine and fuel injector in diesel engine can be used directly to control the start of combustion and the combustion period. However, the combustion of HCCI engine is controlled by the chemical kinetic mainly due to the temperature histories in the cylinder. Therefore the combustion process of HCCI engine cannot be directly controlled. Ion sensors such as a spark plug or a gasket are useful to detect the combustion information in production engines. In this study, the ion current was measured in an HCCI engine with the heated charge mixture of fuel and air without EGR when the charge temperature, equivalence ratio and fuel were varied. Simultaneously in-cylinder pressure was measured and the rate of heat release was calculated. The relationship between the rate of heat release and the ion current is mainly discussed.

Non-intrusive measurement of transient unburned gas temperatures was developed with a fiber-optic heterodyne interferometry system. Using the value of the Gladstone-Dale constant for DME gas and combustion pressure we can calculate the in-cylinder temperature inside unburned and burned region. In this experimental study, it was performed to set up a fiber-optic heterodyne interferometry technique to measure the temperature before and behind the combustion region in a DME-HCCI engine. At first, measured temperature was almost the same as the temperature history assuming that the process that changes of the unburned and the burned are polytropic. In addition, we measured the temperature after combustion which of condition was burned gas with DME-HCCI combustion. The developed heterodyne interferometry used the spark-plug-in fiber-optic sensor has a good feasibility to measure the unburned and burned temperature history.

Emissions remain a critical issue affecting engine design and operation, while energy conservation is becoming increasingly important. One approach to favorably address these issues is to achieve homogeneous charge combustion and stratified charge combustion at lower peak temperatures with a variable compression ratio, a variable intake temperature and a trapped rate of the EGR using NVO (negative valve overlap). This experiment was attempted to investigate the origins of these lower temperature auto-ignition phenomena with SCCI and CAI using gasoline fuel. In case of SCCI, the combustion and emission characteristics of gasoline-fueled stratified-charge compression ignition (SCCI) engine according to intake temperature and compression ratio was examined. We investigated the effects of relative air/fuel ratio, residual EGR rate and injection timing on the CAI combustion area.

Investigation of knocking combustion in a hydrogen spark-ignition engine is one of the major challenges for future vehicle development. The knock phenomenon in a Spark-Ignition (SI) engine is caused by autoignition of the unburned gas ahead of the flame. The explosive combustion of the end-gas creates a pressure wave that leads to damage of the cylinder wall and the piston head of the engine. We observed autoignition in the end-gas region due to compression by the propagating flame front using a high-speed colour video camera through the optically accessible cylindrical quartz window on the top of the cylinder head. Moreover, a high-speed monochrome video camera operating at a speed of 250, 000 frame/s was used to measure the pressure wave propagation. The goal of this research was to improve our ability to describe the effect of the autoignition process on the end-gas and propagating pressure wave during knocking combustion with the help of a high-speed video camera.

The combustion and exhaust emissions characteristics of a supercharged dual-fuel natural gas engine with a single cylinder were analyzed. We focused on EGR (Exhaust Gas Recirculation) to achieve higher thermal efficiency and lower exhaust emissions. The combustion of diesel fuel (gas oil) as ignition sources was visualized using a high-speed video camera from the bottom of a quartz piston. The luminous intensity and flame decreased as the EGR rate increased. Furthermore, the ignition delay became longer due to the EGR. Characteristics of the combustion and exhaust emissions were investigated with changing EGR rates under supercharged conditions. The indicated mean effective pressure and thermal efficiency decreased with increasing EGR rate. In addition, NOx emissions decreased due to the EGR. In this study two-stage combustion was observed.

This study investigated the effect of some pilot fuel injection parameters, like injection timing, injection pressure and injection quantity on engine performance and exhaust emissions of a supercharged producer gas-diesel dual fuel engine. The engine has been tested to be used as a co-generation engine and its power output is an important matter. Experiments have been done to optimize the injection timing, injection pressure and injection quantity for the maximization of engine power. At constant injection pressures, there is an optimum amount of pilot injection quantity for that maximum engine power is developed without knocking and within the limit of maximum cylinder pressure. Above or below of that amount engine power is decreased. Higher injection pressures generally show better results than lower ones. However, good results can also be obtained with lower injection pressure, if maximum power timings can be selected.

Experimental investigations of fuel breakup very close to nozzle of practical high-pressure swirl injector, which is used in gasoline direct injection (GDI) engine, were carried out. In GDI engines, fuel is directly injected into cylinder therefore the spray characteristics and mixture formation are of primary importance. In this research, visualizations of primary spray formation process were demonstrated using a high-speed video camera (maximum speed: 1Mfps) with a long-distance microscope. Initial state and development of the spray were discussed under the different injection pressure condition. During the injection period, the length and thickness of the liquid sheet, which is produced from the nozzle exit, were measured using Ar-ion laser sheet and high-speed camera. Primary spray structure and behavior of liquid sheet, especially surface wave of liquid sheet, at nozzle exit were discussed using obtained images.

In this study, a spark plug sensor for in-situ fuel concentration measurement was applied to a port injected lean-burn engine. Laser infrared absorption method was employed and a 3.392 μm He-Ne laser that coincides with the absorption line of hydrocarbons was used as a light source. In this engine, the secondary valve lift height of intake system was controlled to obtain appropriate swirl and tumble flow in order to achieve lean-burn with the characteristics of intake flow. For such in-cylinder stratified mixture distribution, the fuel concentration near the spark plug is very important factor that affects the combustion characteristics. Therefore, the mixture formation process near the spark plug was investigated with changing fuel injection timing. Under the intake stroke, the timing that fuel passed through near the spark plug depended largely on the fuel injection timing.

A fiber optical heterodyne interferometry system was developed to obtain high temporal resolution temperature histories of unburned and burned gases non-intrusively. The effective optical path length of the test beam changes with the gas density and corresponding changes of the refractive index. Therefore, the temperature history of the gas can be determined from the pressure and phase shift of the interference signal. The resolution of the temperature measurement is approximately 0.5 K, and is dependent upon both the sampling clock speed of the A/D converter and the length of the test section. A polarization-preserving fiber is used to deliver the test beam to and from the test section, to improve the feasibility of the system as a sensor probe. This optical heterodyne interferometry system may also be used for other applications that require gas density and pressure measurements with a fast response time, or a transient temperature record.

It is well known that the wavelet transform is a useful time-frequency analysis method for an unsteady signal and major attention has been focused on the selection of the mother wavelet (MW) because the MW plays an important role in the wavelet transform. In this study, we analyze the pressure signal in a spark-ignition engine and the vibration of the engine block measured by a knock sensor under the knocking conditions when knocking is caused. We then propose a new method of the knocking detection that utilizes the knocking signal measured with a knock sensor as a MW. We call this method the Instantaneous Correlation Method (ICM). The degree of similarity between the MW and the vibration of the engine block was judged and only the knocking signal from the vibration of the engine block was extracted. The results obtained here show that the method proposed in this study is useful for knocking detection even if the engine speed is very high of 6000rpm.

Hydrogen is expected to be one of the most prominent fuels in the near future for solving greenhouse problem, protecting environment and saving petroleum. In this study, a dual fuel engine of hydrogen and diesel oil was investigated. Hydrogen was inducted in a intake port with air and diesel oil was injected into the cylinder. The injection timing was changed over extremely wide range. When the injection timing of diesel fuel into the cylinder is advanced, the diesel oil is well mixed with hydrogen-air mixture and the initial combustion becomes mild. NOx emissions decrease because of lean premixed combustion without the region of high temperature of burned gas. When hydrogen is mixed with inlet air, emissions of HC, CO and CO2 decrease without exhausting smoke while brake thermal efficiency is slightly smaller than that in ordinary diesel combustion.

A dual fuel engine fueled with methane from an inlet port and ignited with diesel fuel was prepared. This study focuses on the effects of early injection and exhaust gas recirculation (EGR) on the characteristics of combustion and exhaust emissions. The injection timing was changed between TDC and 50 degrees before the TDC. In the early injection timing, smoke was never seen and hydrocarbons were smaller compared with those at the normal injection timing. However, the combustion becomes too early to obtain an appropriate torque when the equivalence ratio increases. Then, moderate EGR was very effective to force the combustion to retard with lower NOx, higher thermal efficiency and almost the same hydrocarbons and carbon monoxide. The engine operated even under the condition of stoichiometric mixture.

A chemical kinetics and computational fluid-dynamics (CFD) analysis was performed to evaluate the combustion of syngas derived from biomass and coke-oven solid feedstock in a micro-pilot ignited supercharged dual-fuel engine under lean conditions. For this analysis, a reduced syngas chemical kinetics mechanism was constructed and validated by comparing the ignition delay and laminar flame speed data with those obtained from experiments and other detail chemical kinetics mechanisms available in the literature. The reaction sensitivity analysis was conducted for ignition delay at elevated pressures in order to identify important chemical reactions that govern the combustion process. We have confirmed the statements of other authors that HO2+OH=H2O+O2, H2O2+M=OH+OH+M and H2O2+H=H2+HO2 reactions showed very high sensitivity during high-pressure ignition delay times and had considerable uncertainty.

The objective of this study is to investigate the performance and emissions in a pilot-ignited supercharged dual-fuel engine, fueled with different types of gaseous fuels under various equivalence ratios. It is found that if certain operating conditions are maintained, conventional dual-fuel engine combustion mode can be transformed to the combustion mode with the two-stage heat release. This mode of combustion was called the PREMIER (PREmixed Mixture Ignition in the End-gas Region) combustion. During PREMIER combustion, initially, the combustion progresses as the premixed flame propagation and then, due to the mixture autoignition in the end-gas region, ahead of the propagating flame front, the transition occurs with the rapid increase in the heat release rate.

Effects of injection parameters on combustion and emission characteristics of diesel PCCI engine operating on optical and test engine was investigated. PCCI combustion was achieved through slightly narrow included angle injector, low compression ratio coupled with exhaust gas recirculation. Analysis based on diesel spray evolution, combustion process visualization and analysis was carried out. Spray penetration was evaluated and related to the exhaust emissions. Advancing the injection timing and EGR extended the ignition delay, decreased NOx emissions and increased HC, smoke and CO emissions. Higher injection pressure led to low emissions of NOx, smoke, HC and comparable CO. Optimum spray targeting position for minimum emission was identified. Impingement on the piston surface led to deterioration of emissions and increased fuel consumption while spray targeting the upper edge of Derby hat wall showed improvement in emission and engine performance.

This paper describes the development and application of a spark plug sensor using a 3.392 μm infrared absorption technique to quantify the instantaneous gasoline concentration near the spark plug. We developed an in situ laser infrared absorption method using a spark plug sensor and a 3.392 μm He-Ne laser as the light source; this wavelength coincides with the absorption line of hydrocarbons. First, we established a database of the molar absorption coefficients of premium gasoline at different pressures and temperatures, and determined that the coefficient decreased with increasing pressure above atmospheric pressure. We then demonstrated a procedure for measuring the gasoline concentration accurately using the infrared absorption technique. The history of the molar absorption coefficient of premium gasoline during the experiment was obtained from the established database using measured in-cylinder pressures and temperatures estimated by taking the residual gas into consideration.

A path line method utilizing a CCD random shutter camera and a laser light sheet was applied for obtaining the air mass entrained into a transient gas jet. Large, light weight particles and fine particles were used for scattering the path lines of the surroundings and visualizing the approximate shape of the jet, respectively The jet configuration and the entrainment process could be visualized simultaneously, and this path line method was found to be very useful for estimating the air mass entrained because of the good agreement with the value obtained using LDA data. The spatial and temporal change of the ambient air entrainment into the jet was approximately clarified.

A turbulent gas jet impinging on a flat wall was visualized by a laser sheet method. Velocity fields were determined from the images with a high speed video system by processing them in terms of the cross correlation method for the jet and particle tracking method for the ambient air from the same images. The vortex flow near the transient jet tip impinging on the wall was visualized and analyzed successfully. The velocity field obtained from the above methods was compared to that determined with a laser Doppler anemometer. The path line of a certain period which was taken with a CCD camera with controlled shutter was analyzed and the mean rate of air entrainment was determined quantitatively. The spatial and temporal change of the entrainment rate was estimated and it was found that the entrainment rate near the upstream part of the jet tip region is larger because of the vortex.

In order to reduce the exhaust emission and the fuel consumption in a spark ignition engine, the combustion diagnostics had been developed. However, there are few sensors which can detect the combustion quality for the individual cycle and cylinder in production engines. In previous study, the new technique using a gasket ion sensor for measuring the combustion quality has been proposed. In present study, the flame propagation pattern in a spark ignition engine was detected by using a gasket ion sensor with a circular electrode. The waveforms of ion current obtained from a circular ion sensor were compared with the flame propagation pattern obtained from multiple ion sensors. When the mixture was ignited in offset center of the cylinder, the flame propagation pattern was distorted from the spherical pattern. Then the waveforms of ion current from the circular ion sensor were varied from the waveform for a center ignition.

An investigation was made into two approaches to air-fuel mixture formation in direct injection SI engines in which charge stratification is controlled by swirl or tumble gas motions, respectively. Particle image velocimetry (PIV), laser-induced fluorescence (LIF) and air-fuel ratio measurement by infrared absorption were used to analyze fuel transport from the fuel injector to the spark plug and the fuel vaporization process. The results obtained were then compared with measured data as to combustion stability. As a result, the reason why the effects of injection timing on combustion stability were different between the two approaches was made clear from the standpoint of the mixture formation process.