Search Results

Standard

Hole Placement on Dozer End Bits

1986-05-01

HISTORICAL

J63_198605

It is the purpose of the SAE Recommended Practice to define the minimum requirements for hole placement on Dozer End Bit supports. The recommended practice applies to straight blade, angling blade, U blade, and semi-U blades used on earthmoving tractors per SAE J1057a up to a maximum weight of 100,000 lb (45,000 kg).

Standard

COMPONENT NOMENCLATURE - DUMPERS

1990-07-30

HISTORICAL

J1016_199007

This SAE Standard provides names of major components peculiar to dumpers as defined in SAE J1057 (see Figure 1). Illustrations of components are not intended to be exactly descriptive of any particular machine. For component nomenclature for dumper trailers, refer to SAE J734.

Standard

SPECIFICATION DEFINITIONS—OFF-ROAD WORK MACHINES

1985-01-01

HISTORICAL

J1234_198501

This standard is applicable to off-road work machines, base machine and its equipment, included in categories 1.1, 1.2, 2, 3, and 5 of J1116.

Standard

CAPACITY RATING—DOZER BLADES

1988-03-01

HISTORICAL

J1265_198803

This standard applies only to straight, angling, semi-U, and U-blades for crawler and wheel tractors. It applies to angling blades only in the straight (not angled) position.

Standard

CUTTING EDGE—OPTIONAL CROSS-SECTIONS AND DIMENSIONS LOADER STRAIGHT

1989-09-01

HISTORICAL

J1581_198909

The purpose of this SAE Recommended Practice is to specify dimensions for loader straight cutting edge cross sections without holes and with bolt holes for mounting bolt-on teeth and tooth adaptors on loader buckets described by SAE J731. This recommended practice is intended to supplement SAE J1303 and SAE J1304 with cross sections for heavier duty applications, by identifying larger blunts, greater bevel angles, larger bolt holes, and greater bolt spacing.

Standard

NOMENCLATURE—CRAWLER TRACTOR

1986-01-01

HISTORICAL

J727_198601

This Standard provides names of major components peculiar to crawler tractors as defined in SAE J1057a (June, 1975). Illustrations of components are not intended to be exactly descriptive of any particular machine.

Standard

IDENTIFICATION TERMINOLOGY AND SPECIFICATION DEFINITIONS—PIPELAYERS AND SIDE BOOMS, TRACTOR OR LOADER MOUNTED

1989-06-01

HISTORICAL

J1295_198906

This is applicable to pipelayers and side booms, mounted on tractors or loaders defined in SAE J1057. Only those terms not covered by SAE J1234 are described herein.

Standard

CAPACITY RATING—DUMPER BODY AND TRAILER BODY

1995-11-01

HISTORICAL

J1363_199511

This SAE Standard applies to dumper bodies as defined in SAE J1016 and dumper trailers as defined in SAE J734. It is similar to ISO 6483.

Standard

PRODUCT IDENTIFICATION NUMBERING SYSTEM OF OFF-ROAD WORK MACHINES

1987-09-01

HISTORICAL

J1360_198709

This standard covers off-road, self-propelled work machines (agricultural, construction, forestry, industrial, and mining) as categorized in SAE J1116.

Standard

Lift Capacity Calculation and Test Procedure-Pipelayer and Sideboom

2011-12-08

CURRENT

J743_201112

This SAE Standard describes a method to calculate and a test procedure to validate rated lift capacity as presented in commercial literature for pipelayers and tractors or loaders (wheel or crawler), equipped with a hydraulic or mechanically operated sideboom. Rated lift capacity considers hoist mechanism limits, tipping loads, and rope factor. After the lift capacity is validated by testing, a reduction factor is applied to establish the rated lift capacity for the specific pipelayer or sideboom configuration.

Standard

COMPONENT NOMENCLATURE - CONSTRUCTION TWO- AND FOUR-WHEEL TRACTORS

1990-07-30

HISTORICAL

J869_199007

This SAE Standard provides names of major components peculiar to tractors used with scrapers and dumpers. (See Figures 1 to 3.) Reference SAE J1057. Illustrations of components are not intended to be exactly descriptive of any particular machine.

Standard

COMPONENT NOMENCLATURE - DUMPER TRAILER

1990-07-01

HISTORICAL

J734_199007

See the following sections of SAE J1057 for machine identification: See SAE J1016 for additional component nomenclature.

Standard

CAPACITY RATING—SCRAPER, OPEN BOWL

1993-06-01

HISTORICAL

J741_199306

This SAE Standard specifies a procedure for approximating the volume of typical materials contained in the bowl of Open Bowl scrapers as defined in SAE J728 and SAE J1057. The volumes are based on the inside dimensions of the bowl and representative volumes on top of the bowl. This rating method is intended to provide a consistent means of comparing capacities; it is not intended to define actual capacities that might be observed in any specific application.

Standard

CUTTING EDGE - CROSS SECTIONS LOADER STRAIGHT

1985-02-01

HISTORICAL

J1303_198502

For cutting edges used on buckets for loaders defined in SAE J1057a. The dimensions are applicable to rolled, cast, forged, flame cut, and machined cutting edge sections. Straight cutting edges are defined as those whose leading edge and rear edge are parallel and, thus, are of constant cross section. For "straight cutting edge sections with bolt holes," see SAE J1304 FEB85.

Standard

Identification Terminology of Loaders/Tractors with Forks and Rough Terrain Forklifts

2002-12-19

HISTORICAL

J1464_200212

This SAE Recommended Practice defines machines equipped with forks for material handling, which are intended for use on unimproved or disturbed terrain. (Reference J1116, Categories 1, 2 or 6.)

Standard

IDENTIFICATION TERMINOLOGY OF LOADERS/TRACTORS WITH FORKS AND ROUGH TERRAIN FORKLIFTS

1988-04-01

HISTORICAL

J1464_198804

This recommended practice defines machines equipped with forks for material handling, which are intended for use on unimproved or disturbed terrain. (Reference J1116, Categories 1, 2 or 6.)

Standard

CUTTING EDGE—CURVED GRADER

1991-06-01

HISTORICAL

J739_199106

This SAE Standard is intended for curved cutting edge sections used on graders as defined in SAE J870 and J1057. (See Figure 1 and Table 1.) Hole conformation is further defined in SAE J740 and J1580.

Standard

Earthmoving Machines—Method for Locating the Center of Gravity

1993-09-01

J874_199309

This SAE Standard specifies a method for determining the coordinates of the center of gravity of earthmoving machinery such as tractors, loaders, dumpers, and graders in any condition of loading or position of attachments.

Standard

COMPONENT NOMENCLATURE—LOADER

1985-02-01

HISTORICAL

J731_198502

This standard includes names of major components and parts peculiar to this type machine. The illustrations are descriptive of the principles and are not intended to include all existing commercial machines. [Refer to SAE J1057 JUL73)—Identification Terminology of Earthmoving Machines for machine type.]

Standard

SPECIFICATION DEFINITIONS—LOADERS

1992-06-01

HISTORICAL

J732_199206

This SAE Standard provides uniform definitions of specification terms peculiar to loaders as defined in SAE J1057. The specifications must be qualified by stating the track shoe type, width or the tire type, size, ply, and specified inflation pressure; the model number or type of bucket disregarding teeth; and the type and amount of counterweight and/or ballast, if any, with which the machine is equipped. Paragraphs 4.1 to 4.16 are further defined by Figures 1 to 4. The figures are not intended to be exactly descriptive of any particular machine.