Search Results

A numerical simulation method by transfer matrix method is proposed to compute the vibration stress waveforms of a V-type, 8 cylinder diesel engine crankshaft in this work. This method will be able to predict the conditions of vibration stresses and be useful to design a crankshaft. The accuracy of this numerical method is confirmed by comparing the simulation results of the computation with the measured data. As a result of the comparisons with the measured data, it has been assured that the vibration stress waveforms can be computed with adequate accuracy by considering from 0.5-th to either 10-th or 12-th order per 0.5-th order harmonic components of exciting forces for a 4-cycle engine.

This is the study on the vibration characteristics of the fuel-injection pump body. Recently, refinement of the fuel spray is necessary in order to reduce the toxic substance, which is included in automotive exhaust gas of diesel engine for the automobile. To jet diesel fuel in higher pressure is a method for spraying the fuel more minute into a cylinder. However, this method causes the increase in respect of engine vibration and torque nonuniformity. The fuel-injection pump body receives not only this engine vibration by the method but also impact tute by the high-pressure injection. As this result, the sufficient performance cannot be demonstrated because large vibration deformations occur at the body and the camshaft of the fuel-injection pump. The vibration characteristics of the fuel-injection pump, which can reduce these vibration deformations, are necessary in order to lead to the performance.

The torsional vibration of diesel engines has become severer with the increase of exciting force by higher pressure. Therefore, the running crankshaft is highly stressed owing to the large torsional vibration. Then, torsional viscous fluid dampers of high performance have been employed in high mean effective pressure diesel engines as a measure for vibration reduction. As the dynamic characteristics of the dampers have such a great influence on the vibration of the engine crankshaft system that they cannot be ignored, the viscosity of the silicone oil and the peripheral and lateral gaps of the dampers are diversely varied in the experiment. As the equipment for the measurement of torsional vibration displacement, a phase-shaft type torsiograph equipment was adopted so as to make it easy to measure simultaneously angular displacements of the casing and the inertia ring.

This paper refers to a numerical computation for vibration displacements and stresses of a crankshaft with a shear type rubber torsional damper by the three dimensional transfer matrix method. The accuracy of this computation method is confirmed by comparing computed results with measured ones. Especially, in this work, the numerical computation method is proposed to compute the vibration displacements and stresses by means of replacing the rubber part of rubber torsional damper with a spring-dashpot model. Then dynamic characteristics are estimated by the complex torsional stiffness derived from a three-element Maxwell model. As a result the torsional vibration stress and bending vibration stress and vibration displacements (angular and lateral displacements) can be computed with an adequate accuracy. This computation method is applicable to predicting the conditions of vibration displacements and stresses, and will contribute to optimum design of the crankshaft.

Described herein is an experimental and theoretical study of the dynamic properties of torsional viscous-friction dampers for use on Diesel engines and the characteristics of torsional vibration of the engine shaftings. At first, three kinds of dampers are fitted to a 14.3 liter, V-type, 8-cylinder Diesel engine and the torsional vibration displacements at the pulley are measured in order to investigate the characteristics of torsional vibration of the shaftings with the damper. The kinematic viscosity of silicone oil is diversely varied in this experiment. It is confirmed that an optimum viscosity exists for each damper from an experimental viewpoint. Next, the dynamic properties of the dampers and the characteristics of torsional vibrations of the engine shaftings are investigated by 3 dimensional analysis of forced vibration by the transfer matrix method, which has been developed by the authors.

The unknown characteristics of the bending vibration coupled with torsional vibration (hereafter called“coupled torsional, bending vibration”) are investigated from the experimental and analytical viewpoints. The torsional and bending vibration stresses of the crankshafts of a 6 cylinder, in - line engine and an 8 cylinder, V - type engine are measured first in order to investigate experimentally the characteristics of the coupled torsional - bending vibrations. Next, the displacements, moments and stresses of the torsional and bending vibrations of the above - mentioned crankshaft are calculated by 3 dimensional, forced vibration analysis of the crankshafting of the V 8 engine using the transfer matrix method, which has been developed by the authors. Finally, the experimental results are compared with the corresponding calculated results and the characteristics of the bending vibration stresses coupled with the large torsional vibrations are made clear.

Automotive diesel engines have been developed with the aim of achieving higher performance and lighter weight. Since the torsional vibration stresses of the crankshafts have become severer with increase of specific power, torsional vibration rubber dampers of shear-type have been widely used in order to reduce the vibrations. However, the dynamic characteristics of the dampers depend on amplitude, frequency, temperature and secular change effects. Therefore, the dynamic characteristics should be separately investigated with every influence factor. This indicates that it is difficult for the damper designers to predict the dynamic characteristics of the torsional vibration dampers in engine operation. This paper refers mainly to the dynamic characteristics of shear-type torsional rubber dampers with rubber vibration isolator hardened by secular change.

This paper refers to a numerical calculation method, in which the transition matrix method is employed. The method estimates torsional vibration amplitude of a crankshaft with a rubber damper by taking the dynamic characteristics of the rubber part into consideration. Firstly, the rubber part is replaced with a three-elemental Maxwell model, which is determined by the results of static tests, such as stress relaxation test, creep test and static torsional test. The basic data used for the determination of the element values on the Maxwell model are obtained by these tests. Secondly, the vibration system of a crankshaft with a rubber damper is replaced with a linear lumped model, in which the torsional stiffness and damping coefficient of the damper rubber part are decided by using the element values of the Maxwell model.

The production unit number of small diesel engine cars tends to decline except recreational vehicles in Japanese market in recent years, while the production unit number in Europe market keeps on increasing owing to the merits of the durability and the fuel consumption. The small diesel engines will have to be improved in the near future by solving major problems such as noise and vibration pollution, environmental pollution, improvement in performance of diesel engines, in order to expand the production of the engines. This paper refers to a basic study on the experimental and analytical methods for the reduction of resonant vibration in each vibration mode on some cylinder blocks of small high-speed diesel engines in rated engine speed range. Hammering test method, which is easy and useful for measuring frequency response functions, is carried out in the experiments.

The dynamic characteristics of conventional viscous-friction dampers are investigated in this paper by adopting simultaneous vibration measurement method at two points. The vibration displacements of the damper casing and the inertia ring can be simultaneously measured in this method. It has become possible that the more detailed dynamic characteristics of the viscous-friction damper can be grasped by the method. Especially, it is an effective method to grasp the behaviors of the inertia ring and the damper casing for clarifying the effect of the silicone fluid on the torsional vibration of crankshaft system. The damper casing was made of acrylic resin in order to measure the behavior of the inertia ring on engine operation. It is possible to measure the torsional vibration displacements waveforms by the optical signals from pulse tapes stuck in both peripheral sides of the damper casing and the inertia ring.