Search Results

This paper describes the joint development by Tenneco and Pi Shurlok of a complete diesel engine aftertreatment system for controlling particulate matter emissions. The system consists of a DOC, DPF, sensors, controller and an exhaust fuel injection system to allow active DPF regeneration. The mechanical components were designed for flow uniformity, low backpressure and component durability. The overall package is intended as a complete PM control system solution for OEMs, which does not require any significant additions to the OEM's engine control strategies and minimizes integration complexity. Thus, to make it easier to adapt to different engine platforms, ranging from small off-road vehicle engines to large locomotive engines, model-based control algorithms were developed in preference to map-based controls.

Evolving marine diesel emission regulations drive significant reductions of nitrogen oxide (NOx) emissions. There is, therefore, considerable interest to develop and validate Selective Catalytic Reduction (SCR) converters for marine diesel NOx emission control. Substrates in marine applications need to be robust to survive the high sulfur content of marine fuels and must offer cost and pressure drop benefits. In principle, extruded honeycomb substrates of higher cell density offer benefits on system volume and provide increased catalyst area (in direct trade-off with increased pressure drop). However higher cell densities may become more easily plugged by deposition of soot and/or sulfate particulates, on the inlet face of the monolithic converter, as well as on the channel walls and catalyst coating, eventually leading to unacceptable flow restriction or suppression of catalytic function.

Monolithic emission control devices typically use a support mat material to provide mechanical support, mechanical isolation, and thermal insulation for ceramic monoliths. This material is similar to a felt, but made from ceramic fibers. Non-intumescent support mat materials contain only ceramic fibers and binder compounds, while intumescent support mats also contain vermiculite; a material that expands with the application of heat. The durability of the support mat is critical to the durability of the overall emission control components. In addition to many component validation methods that evaluate the durability of the entire system methods to evaluate the response and predict the durability of the support mat itself help provide important design information. This paper summarizes challenges and artifacts in support mat testing.

2010 and future EPA regulations introduce stringent Oxides of Nitrogen (NOx) reduction targets for diesel engines. Selective Catalytic Reduction (SCR) of NOx by Urea over catalyst has become one of the main solutions to achieve these aggressive reductions. As such, urea solution is injected into the exhaust gas, evaporated and decomposed to ammonia via mixing with the hot exhaust gas before passing through an SCR catalyst. Urea mixers, in this regard, are crucial to ensure successful evaporation and mixing since its liquid state poses significant barriers, especially at low temperature conditions that incur undesired deposits. Intensive efforts have been taken toward developing such urea mixers, and multiple criteria have been derived for them, mainly including NOx reduction efficiency and uniformity. In addition, mixers must also satisfy other requirements such as low pressure drop penalty, mechanical strength, material integrity, low cost, and manufacturability.

An active diesel particulate filter (DPF) regeneration system is evaluated, which applies secondary fuel injection (SFI) directly within the exhaust system upstream of a diesel oxidation catalyst (DOC). Diesel fuel is oxidized in the presence of a proprietary catalyst system, increasing exhaust gas temperatures in an efficient and controlled manner, even during low engine-out gas temperatures. The exotherms produced by secondary fuel injection (SFI) have been evaluated using two different DOC volumes and platinum catalyst loadings. DOC light-off temperatures were measured using SFI under steady-state conditions on an engine dynamometer. A ΔT method was used for the light-off temperature measurements – i.e., the minimum DOC inlet gas temperature at which the exothermic reaction increases the outlet gas temperature 20°C or greater than the inlet temperature.

The presented work evaluates several mixer designs being considered for use in large Diesel exhaust aftertreatment systems. The mixers are placed upstream of a diesel oxidation catalyst (DOC) in the exhaust system, where a liquid hydrocarbon fuel is injected. DOC exothermic behaviour resulting from each mixer at different operating conditions is evaluated. A gas flow bench equipped with a XY-Table measurement system is used to determine gas velocity, temperature, and hydrocarbon species uniformity, as well as, pressure drop. Experimental mixer data obtained from a flow bench and an engine dynamometer are compared and discussed. The experimental methodology used in this study can be used to evaluate mixers via comprehensive testing.

External Exhaust Gas Recirculation (EGR) has been used on diesel engines for decades and has also been used on gasoline engines in the past. It is recently reintroduced on gasoline engines to improve fuel economy at mid and high engine load conditions, where EGR can reduce throttling losses and fuel enrichment. Fuel enrichment causes fuel penalty and high soot particulates, as well as hydrocarbon (HC) emissions, all of which are limited by emissions regulations. Under stoichiometric conditions, gasoline engines can be operated at high EGR rates (> 20%), but more than diesel engines, its intake gas including external EGR needs extreme cooling (down to ~50°C) to gain the maximum fuel economy improvement. However, external EGR and its problems at low temperatures (fouling, corrosion & condensation) are well known.

It is important to quantitatively characterize the automotive events in order to not only accurately interpret their past but also to reliably predict and forecast their short-term, medium-term, and even long-term future. In this paper, several automotive industry related events, i.e. vehicle safety, vehicle weight/HP ratio, the emissions of CO2, HC, CO, and NOx, are analyzed to find their general trends. Exponential and power law functions are used to empirically fit and quantitatively characterize these data with an emphasis on the two functions’ effectiveness in predictability. Finally, three empirical emission laws based on the historical HC, CO, and NOx data are proposed and the impact of these laws on emission control is discussed.

Water injection (WI) can improve gasoline engine performance and efficiency, and on-board water recovery technology could eliminate the need for customers to refill an on-board water reservoir. In this regard, the technical feasibility of exhaust water recovery (EWR) is described in this paper. Water injection testing was conducted at a full load condition (5000 rpm/18.1 bar BMEP) and a high load condition (3000 rpm/14.0 bar BMEP) on a turbocharged gasoline direction injection (GTDI) engine. Water recovery testing was conducted both after the exhaust gas recirculation (EGR) cooler and after the charge air cooler (CAC) at a high load (3000 rpm/14.0 bar BMEP), as well as a part load (2080 rpm/6.8 bar BMEP) condition, at temperatures ca. 10-15 °C below the dew point of the flow stream. Three types of water separation designs were tested: a passive cyclone separator (CS), a passive membrane separator (MEM), and an active separator (AS).

A series of novel metal-oxide (TiO2, TiO2-SiO2)-supported Mn, Fe, Co, V, Cu and Ce catalysts were prepared by incipient wetness technique and investigated for the low-temperature selective catalytic reduction (SCR) of NOx with ammonia at industrial relevantly conditions. Among all the prepared catalysts, Cu/TiO2 showed superior de-NOx performance in the temperature range of 150-200 °C followed by Mn/TiO2 in the temperature range of 200-250 °C. The Ce/TiO2 catalyst exhibited a broad temperature window with notable de-NOx performance in the temperature regime of 250-350 °C. The phyico-chemical characterization results revealed that the activity enhancement was correlated with the properties of the support material. All the anatasetitania-supported catalysts (M/TiO2 (Hombikat)) demonstrated significantly high de-NOx performance above 150 °C.

The main objective of this work is to develop a low-temperature SCR catalyst for the reduction of nitrogen oxides at cold start, low-idle and low-load conditions. A series of metal oxide- incorporated beta zeolite catalysts were prepared by adopting incipient wetness technique, cation-exchange, deposition-precipitation and other synthesis techniques. The resulting catalysts were characterized and tested for reduction of NOx in a fixed bed continuous flow quartz micro-reactor using ammonia as the reductant gas. Initial catalyst formulations have been exhibited good NOx reduction activity at low-temperatures. These catalyst formulations showed a maximum NOx conversion in the temperature range of 100 - 350°C. Besides, more experiments were performed with the aim of optimizing these formulations with respect to the metal atomic ratio, preparation method, active components and supported metal type.

Secondary fuel injection is applied to facilitate active soot management of the particulate filter within diesel aftertreatment systems, avoiding concerns with fuel delivery via in-cylinder post-injection. System performance is dependent on the thermo-fluid interactions of the injected fuel with the exhaust stream, with the intent of having more fully vaporized fuel and a well-mixed air-fuel mixture at the inlet of the oxidation catalyst for uniform thermal distribution as it exothermically reacts. Pre-heating the fuel with a diesel vaporizer prior to its delivery into the exhaust enables improved system performance, reducing droplet sizes and mixing demands. A diesel vaporizer is applied within the exhaust of a medium duty truck application, and the response of the catalyst is characterized across a variety of conditions.