Search Results

Battery Electric Vehicles and Extended Range Electric Vehicles, like the Chevrolet Volt, can use electrical energy from the Grid to meet the majority of a driver�s transportation needs. This has the positive societal effects of displace petroleum consumption and associated pollutants from combustion on a well to wheels basis, as well as reduced energy costs for the driver. CO2 may also be lower, but this depends upon the nature of the grid energy generation. There is a mix of sources � coal-fired, gas -fired, nuclear or renewables, like hydro, solar, wind or biomass for grid electrical energy. This mix changes by region, and also on the weather and time of day. By monitoring the grid mix and communicating it to drivers (or to their vehicles) in real-time, electrically driven vehicles may be recharged to take advantage of the lowest CO2, and potentially lower cost charging opportunities.

Combustion characteristics of dimethyl ether, DME, have been investigated experimentally, in a heavy duty single cylinder engine equipped with an adapted common rail fuel injection system, and the effects of varying injection timing, rail pressure and exhaust gas recirculation on the combustion and emission parameters. The results show that DME combustion does not produce soot and with the use of exhaust gas recirculation NOX emissions can also be reduced to very low levels. However, high injection pressure and/or a DME adopted combustion system is required to improve the mixing process and thus reduce the combustion duration and carbon monoxide emissions.

Today CFD is an important tool for engineers in the automotive industry who model and simulate fluid flow. For the complex field of Underhood Thermal Management, CFD has become a very important tool to engineer the cooling airflow process in the engine bay of vehicles. To model the cooling airflow process accurately in CFD, it is of utmost importance to model all components in the cooling airflow path accurately. These components are the heat exchangers, fan and engine bay blockage effect. This paper presents CFD simulations together with correlating measurements of a cooling airflow system placed in a test rig. The system contains a heavy duty truck louvered fin radiator core, fan shroud, fan ring and fan. Behind the cooling module and fan, a 1D engine silhouette is placed to mimic the blockage done by a truck engine. Furthermore, a simple hood is mounted over the module to mimic the guiding of air done by the hood shape in an engine bay.

In order to meet emissions and power requirements, modern engine design has evolved in complexity and control. The cost and time restraints of calibration and testing of various control strategies have made virtual testing environments increasingly popular. Using Hardware-in-the-Loop (HiL), Volvo Penta has built a virtual test rig named VIRTEC for efficient engine testing, using a model simulating a fully instrumented engine. This paper presents an innovative Artificial Neural Network (ANN) based model for engine simulations in HiL environment. The engine model, herein called Artificial Neural Network Engine (ANN-E), was built for D8-600 hp Volvo Penta engine, and directly implemented in the VIRTEC system. ANN-E uses a combination of feedforward and recursive ANNs, processing 7 actuator signals from the engine management system (EMS) to provide 30 output signals.

In order to avoid the high CO and HC emissions associated with low temperature when using high levels of EGR, partially premixed combustion is an interesting possibility. One way to achieve this combustion mode is to increase the ignition delay by adjusting the inlet valve closing timing, and thus the effective compression ratio. The purpose of this study was to investigate experimentally the possibilities of using late and early inlet valve closure to reduce NOx emissions without increasing emissions of soot or unburned hydrocarbons, or fuel consumption. The effect of increasing the swirl number (from 0.2 to 2.5) was also investigated. The combustion timing (CA50) was kept constant by adjusting the start of injection and the possibilities of optimizing combustion using EGR and high injection pressures were investigated. Furthermore, the airflow was kept constant for a given EGR level.

An engine model for use in computer simulation of transient behavior in drivetrain and vehicle systems is presented. Two elements, important for deviation (e.g. turbo-lag) from steady state characteristics, are the inertia of the supercharging unit (turbo shaft) and the fuel injection control system. No extensive combustion calculations are carried out within the model. Instead it uses condensed results from existing combustion models and measurements. The model is semi-empirical. Some of the engine specific properties needed for simulation are (e.g. for a turbocharged diesel): engine data in steady state operation, mappings of compressor and turbine performance, inertia of the engine components condensed to the crankshaft, turbo shaft inertia, displacement, compression ratio and the essentials of the fuel injection control strategy. Input parameters to the computer program based on the model are accelerator pedal position and external torque acting on the flywheel.

Thermodynamic power cycles have been shown to provide an excellent method for waste heat recovery (WHR) in internal combustion engines. By capturing and reusing heat that would otherwise be lost to the environment, the efficiency of engines can be increased. This study evaluates the maximum power output of different cycles used for WHR in a heavy duty Diesel engine with a focus on working fluid selection. Typically, only high temperature heat sources are evaluated for WHR in engines, whereas this study also considers the potential of WHR from the coolant. To recover the heat, four types of power cycles were evaluated: the organic Rankine cycle (ORC), transcritical Rankine cycle, trilateral flash cycle, and organic flash cycle. This paper allows for a direct comparison of these cycles by simulating all cycles using the same boundary conditions and working fluids.

Powertrain efficiency is a critical factor in lowering fuel consumption and reducing the emission of greenhouse gases for an internal combustion engine. One method to increase the powertrain efficiency is to recover some of the wasted heat from the engine using a waste heat recovery system e.g. an organic Rankine cycle. Most waste heat recovery systems in use today for combustion engines use the waste heat from the exhaust gases due to the high temperatures and hence, high energy quality. However, the coolant represents a major source of waste heat in the engine that is mostly overlooked due to its lower temperature. This paper studies the potential of using elevated coolant temperatures in internal combustion engines to improve the viability of low temperature waste heat recovery.

Laws concerning emissions from heavy duty (HD) internal combustion engines are becoming increasingly stringent. New engine technologies are needed to satisfy these new requirements and to reduce fossil fuel dependency. One way to achieve both objectives can be to partially replace fossil fuels with alternatives that are sustainable with respect to emissions of greenhouse gases, particulates and nitrogen oxides (NOx). A suitable candidate is methanol. The aim of the study presented here was to investigate the possible advantages of combusting methanol in a heavy duty Diesel engine. Those are, among others, lower particulate emissions and thereby bypassing the NOx-soot trade-off. Because of methanol’s poor auto-ignition properties, Diesel was used as an igniting sources and both fuels were separately direct injected. Therefore, two separate standard common rail Diesel injection systems were used together with a newly designed cylinder head and adapted injection nozzles.

The transport sector is experiencing a shift to zero-carbon powertrains driven by aggressive international policies aiming to fight climate change. Battery electric vehicles (BEVs) will play the main role in passenger car applications, while diversified solutions are under investigation for the heavy-duty sector. Within this framework, Light Commercial Vehicles (LCVs) impact is not negligible and accountable for about 2.5% of greenhouse gas (GHG) emissions in Europe. In this regard, few LCV comparative assessments on green powertrains are available in the scientific literature and justified by the fact that several factors and limitations should be considered and addressed to define optimal powertrain solutions for specific use cases. The proposed research study deals with a comparative numerical assessment of different zero-carbon powertrain solutions for LCV. BEVs are compared to hydrogen-based fuel cells (FC) and internal combustion engines (ICE) powered vehicles.

A serie of experiments were carried out to compare the combustion and emissions characteristics of a diesel engine using non-circular (elliptical) and circular shaped fuel injector nozzle holes. Elliptic nozzle holes have the potential to increase air entrainment into the spray, which could lead to decreased emissions from diesel combustion. Previous work [6,7] has shown some interesting results in a passenger car diesel engine and also in a single cylinder engine with optical access. The idea is based on results from investigations of gas jets, where the air entrainment for elliptical jets was increased substantially compared to circular jets. The present series of experiments were carried out to further investigate these effects. The non-circular holes, which were made with an aspect ratio of close to 2:1, have a similar flow rate as the conventional circular holes. Two different angles of the elliptical major axis to the injector centerline were used.

The transportation sector still depends on conventional engines in many countries as the alternative technologies are not mature enough to reduce carbon footprints in society. The four-stroke diesel engines, primarily used for heavy-duty applications, need either high intake boosting or a large bore to produce higher torque and power output. There is an alternative where a four-stroke engine operated in two-stroke mode with the help of a fully flexible variable valve actuation (VVA) system can achieve similar power density without raising the intake boosting or engine size. A fully flexible VVA is required to control the valve events (lift, timing, and durations) independently so that the four-stroke events can be completed in one cycle. In this study, 1D-3D CFD coupled simulations were performed to develop a gas exchange process for better air entrapment in the cylinder and evacuate the exhaust products simultaneously.