Search Results

This paper discusses the test setup and methodology required to validate complete lift axle assembly for simulating the real time test track data. The correlation of rig vs track is discussed. The approach for reduction of validation time by eliminating few of the non-damaging tracks/events, its correlation with real life condition is discussed, and details are presented. With increased competition, vehicle development time has reduced drastically in recent past. Bench test procedure using accelerated test cycle discussed in this paper will help to reduce development time and cost. Process briefed in this paper can also be used for similar test specification for other structural parts or complete suspension system of heavy commercial vehicles.

The public transport in India is gradually shifting towards electric mobility. Long range in electric mobility can be served with High Voltage Battery (HVB), but HVB can sustain for its designed life if it’s maintained within a specific operating temperature range. Appropriate battery thermal management through Battery Cooling System (BCS) is critical for vehicle range and battery durability This work focus on two aspects, BCS sizing and its coolant flow optimization in Electric bus. BCS modelling was done in 1D CAE software. The objective is to develop a model of BCS in virtual environment to replicate the physical testing. Electric bus contain numerous battery packs and a complex piping in its cooling system. BCS sizing simulation was performed to keep the battery packs in operating temperature range.

Small commercial vehicles (SCVs) are the drivers of a major part of India’s indirect economy, providing the most efficient means of transport. With the introduction of BS-VI norms, some major overhauls have been done to the SCV models to meet BS VI norms in challenging timeline for early market entry. This forced to automotive designers towards challenge of cost competitiveness as well as refinement level to survive in this competitive market. This paper explains the systematic approach used to overcome challenges of higher tactile vibrations, higher in-cab noise because of BS VI requirement in 2 cycle engine required for small commercial vehicle. The solutions were need to be worked out without compromising the other performance attributes like total cost of ownership, fuel economy, ease of servicing and cost effectiveness.

The automotive sector is going through a phase of stiff competition among various Original Equipment Manufacturers for increasing their profitability while ensuring highest levels of customer satisfaction. The biggest challenge for such companies lies in minimizing their overall cost involving investments in Research and Development, manufacturing, after sales service and warranty costs. Higher warranty costs not only affect the net profit but in turn it also affects the brand image of the company to a large extent in the long run. An effort is made here to target such warranty costs due to frequent tail pinion and hub seal leakages on single reduction/hub reduction axles of Heavy Commercial Vehicles in the field. A preliminary study involving the severity analysis of such failures is followed by a step by step investigation of these failures.

There has been immense focus on Gear Shift Quality as it is seen as an important factor for subjective evaluation of driving comfort of a vehicle with manual transmission. Synchronizer and driveline stiffness optimization is often the only area of focus for gear shift quality during early design stage. Proven Simulation models are already available for predicting the effect of synchronizer and driveline stiffness. Though Gear shift cable also has a significant effect on gear shift quality, neither design guidelines nor simulation models are available for predicting gear shift cable performance. Designers have relied on physical approach to establish cable routing, since cable routing cannot be predicted on virtual vehicle. In design phase cable routing is imagined and modeled in CAD using constrained curve geometry and later on established by physical trials on vehicle with various cable lengths, routing paths and clamp positions.

Diesel engine fuel hose return line is considered as a low pressure line and consists of two layers. The inner layer is used to carry the excess fuel, thereby hose material shall have resistance to fuel and its residues. The outer layer is used to protect inner layer from heat, ozone and oil spillage, thereby outer cover material shall have resistance against the heat, ozone and engine oil. Currently NBR PVC, NBR and FKM materials have been used as inner layer materials in diesel engine fuel hose outer cover application, according to service temperature. Halogen contained CSM material has been used for outer cover application and the production of CSM material was withdrawn by one of the major manufacturer recently. Current global challenge is to use environment friendly material in vehicle components to make hazardous free environment. To replace CSM material, which contains Halogen, the available options are CPE, CR, HNBR and AEM materials.

In case of new generation of commercial vehicles, three shaft transmissions are designed with press fitted gears on counter shaft. It allows user to save the cost of transmission manufacturing by considerable amount. In case of heavy commercial vehicles, which are being used in abusive conditions such as mining and off-road applications, it becomes absolutely necessary to ensure that the gears press fit should withstand the continuous loads and impact loads. There are design guidelines available to ensure proper fit and torque carrying capacity between the mating parts. Still, there are gear slippage, shaft and gear breakage failures in the field. In this scenario, there is a need to develop bench test procedure which will capture such failures in the prototype stage. Looking at the failures in the field, it is necessary to capture all above hidden failures in design validation phase.

Lift axles of heavy commercial vehicles are deployed to handle increased payload. These axles of Commercial vehicles are made of low alloy carbon steel materials. Lift axles are designed in hollow condition for weight reduction opportunity. Two types of tube materials are used for the manufacturing of lift axles. These are either Cold Drawn Seamless (CDS) tubes or Hot Finished Seamless (HFS) tube material. The vanadium micro-alloyed steel grade, 20MnV6 is an excellent choice for the manufacturing of lift axles. The 20MnV6 has favorable mechanical properties for lift axles and also offers good weldability. However, lift axles made of 20MnV6 when manufactured in hot-finished condition, shows significant scatter in terms of durability performance. This requires further heat treatment of 20MnV6 to be deployed for reducing the scatter in the material properties to reduce scatter in durability performance and thus increasing the reliability of the lift axles.

Subject paper focuses primarily on non uniform tire wear problem of front steered wheels in a pickup model. Cause and effect analysis complemented with field vehicle investigations helped to identify some of the critical design areas. Investigation revealed that steering geometry of the vehicle is undergoing huge variations in dynamic condition as compared to initial static setting. Factors contributing to this behavior are identified and subsequently worked upon followed by a detailed simulation study in order to reproduce the field failures on test vehicles. Similar evaluation with modified steering design package is conducted and results are compared for assessing the improvements achieved. In usual practice, it is considered enough if Steering Geometry parameters are set in static condition and ensured to lie within design specifications.

In automobile design, a rear-engine layout mainly espoused for small entry-level cars and light commercial vehicles for three reasons - packaging, traction, and ease of manufacturing. The aim of this paper is to strategize cooling system of rear-mounted engine of a small gasoline car. Radiator and cooling fan packaged close to engine at rear of the car for simple packaging. Efficient thermal management ensured by robust overheat protection stratagem using EMS software. DFSS, a disciplined problem prevention approach that helps in achieving the most optimum design solution and provides improved and cost effective quality products; is used to finalize an optimum design based on the analysis of the various tests carried out as per DOE [1]. This paper is about designing a distinctive cooling system of a car having rear-mounted engine with rear radiator but front mounted HVAC system [2].

The commercial vehicle market in India is shifting to higher payload capacity vehicles due to a lower transportation cost per unit goods. To cater this requirement, the vehicle manufacturers are designing the heavy multi-axle commercial vehicles and with higher per axle loading capacity. One of such a vehicle design involves five-axle vehicle with non-steerable, twin tire, lift axle. Though using a twin tires have increased loading capacity of lift axle compared to a single tire self-steerable lift axle, it can cause tire scrub while vehicle is turning and leads to a significant tire wear. The tire wear possibility due to use of non-steerable lift axle is estimated through simulation using full vehicle model in ADAMS. The operating zone of the vehicle, where maximum tire wear can occur, is identified through simulation. Different alternatives to reduce tire wear for this scenario are also discussed.

Noise Vibration and Harshness (NVH) refinement is one of the important parameters in modern vehicle development. In city traffic conditions, idling is an engine operating condition where a driver focuses attention more to his/her vehicle. Tactile vibration & noise levels inside the cab play an important role in all vehicles, especially those powered by diesel engines where combustion pressures are higher. They lead to discomfort & fatigue of passengers of even a low cost vehicle. Now its idle NVH is influenced mainly by vibration-isolation provided by power-train (PT) mounting design, This paper describes steps taken to improve the idle vibrations at a driver seat of a small commercial vehicle (SCV) with a 2-cylinder diesel engine of 800 cc through redesign of PT-mounting along with fine tuning of idle speed of the engine. A resonance was avoided between the first firing order at idling and PT rigid-body mode in pitching.

The Indian automotive industry has taken a big leap towards stringent Bharat Stage VI (BS VI) emission standards by year 2020. A digital driven design and development focusing on innovative and commercially viable technologies for combustion and exhaust after-treatment system is the need of the time. One-dimensional (1D) simulation serves as a best alternative to its counterparts in terms of obtaining faster and accurate results, which makes it an ideal tool for carrying out optimization studies at system level. In this work, 1D chemical kinetics modelling and analysis of exhaust after-treatment system (EAT) for a heavy-duty diesel has been performed using GT-Power. Initially, a single site 1D model for a diesel oxidation catalyst (DOC) has been developed and then, a two-site, 1D model for a selective catalytic reduction (SCR) catalyst was also developed based on reactor data.

HVAC system design has an accountability towards acoustic comfort of passengers of a vehicle. Owing to larger cabin volume of a bus, multiple air blowers have to be installed to ensure comfort of passengers. Such multiple blowers produce significant flow induced noise inside the cabin. For commercial success, it becomes essential to predict intensity of such a flow induced noise at very early stages in product development. Conventionally sliding mesh based CFD approach is deployed to predict flow and turbulence noise around each blower. However due to complexity, this method becomes computationally intensive resulting in cost and time inefficiency. Hence it is desirable to innovate around an alternative rapid, reliable prediction method, which ensures quick turnaround of prediction.

Modern day diesel engines use systems like Exhaust Gas Recirculation (EGR), Variable Geometric Turbo Charger (VGT), inlet throttle for air regulation, multiple injection strategies, high pressure rail systems for fuel regulation to optimize the combustion for meeting the strict emission and fuel consumption demands. Torque based ECU structures which are commonly used for diesel engines require a large amount of calibration work. Conventional manual methods for emission and fuel consumption optimization (Full factorial or Line search method) results in increased test bed usage and it is almost impossible to use these methods as the number of parameters to optimize are very high. The conventional DoE tests have been limited by the necessity of calibration engineer’s expertise and manual prescreening of test points to be within thermal & mechanical limits of engine systems. This subsequently leads to excessive screening of variables; which is time consuming.

In India, around 70 million people travel by public transport buses. With rising air pollution across cities, there is a need to safeguard passengers from inhaling polluted air. Contaminants in such polluted air could be fine to coarse dust (2.5 micron to 100 micron), exhaust gases (oxide of sulphur, nitrogen and carbon), total volatile organic compounds, bacteria and viruses arising out of covid-19 pandemic. Passengers commuting in buses are continuously inhaling air that is re-circulating through the Air Conditioning system (AC) and also comes in contact with multiple co-passengers and touch points. This air potentially carries a high dose of contaminants and inhalation of such air can lead to health issues. Vehicle manufacturers intend to provide clean air inside the vehicle cabin by configuring various Air Purification systems (AP) which reduce air contaminants in the closed space of a cabin.

Commercial electric vehicle air conditioning system keeps occupants comfortable, but at the expense of the energy used from the battery of vehicle. Passengers around the world are increasingly requesting buses with HVAC/AC capabilities. There is a need to optimise current air conditioning systems taking into account packaging, cost, and performance limits due to the rising demand for cooling and heating globally. Major elements contributing to heat ingress are traction motor, front firewall, windshield & side glasses and bus body parts. These elements contribute to the bus’s poor cooling and lack of passenger comfort. This topic refers to the reduction of the heat ingress through usage of different glass technology like IR Cut & solar green glass with different types of coating.

Battery cooling system plays a vital role in all kind of Electric vehicles. For Indian applications where vehicles will be subjected to slower speeds due to heavy traffic, higher ambient conditions and excess loading pattern in commercial vehicles, designing a Battery cooling system (BCS) is a challenging task. There are various options for cooling of battery i.e. Natural air cooled, forced air cooled, indirect cooling. This paper discusses about indirect coolant based cooling of battery of a small commercial vehicle. Battery cooling system works on the principle of Indirect cooling with the combination of vapor compression cycle and water-coolant mixture path. R134a gas used for VCRS system and for cooling system used 50-50% water glycol coolant mixture. For this type of battery cooling system typically There are challenges of packaging of various battery cooling parts, hose routing, pipe bends which may result in de aeration issues.

AC system provides the human comfort inside the cabin of a vehicle but at the expense of consumption of energy from the vehicle. On a global perspective for the bus segment, there is an increased demand for cooling in tropical countries. Optimization needs to be done in existing AC systems w.r.t packaging, cost & performance constraints. Major elements contributing to heat ingress are engine hood, front firewall, windshield & side glasses and bus body parts. Due to these reasons inadequate passenger comfort and poor cool down performance of the vehicle is observed. This paper refers to the reduction of heat ingress through different DOE (Design of Experiment) in the area of design & validation for duct & vent layout, insulation, glass & paint technology, evaporator blowers. The new duct design has been evaluated using a CFD tool by varying various parameters to generate desired output. The integrated use of the modifications was found significant improvement at vehicle level.

The automotive world is moving towards electric powertrain systems. The electric powertrain systems have emerged as a promising alternative to the conventional powertrain system. The performance of electric vehicle is highly dependent on operating temperature of electric and electronic components of the vehicle. All power electronics and electric components in EV generate heat during operation and it must be removed to prevent overheating of components. Higher temperatures raise safety concerns whereas lower temperatures deteriorate the performance of power electronics & electric components. These power electronics & electrical components perform efficiently and safely if operated within certain temperature range. This paper presents an advanced efficient cost-effective thermal technique for small commercial electric vehicle (SCEV) to improve the performance & life of major electric components.