Search Results

Engine mounts are an integral part of the vehicle that helps in reducing the vibrations generated from the engine. Engine mounts require a simple yet complicated amalgamation of two very different materials, steel and rubber. Proper adhesion between the two is required to prevent any part failure. Therefore, it becomes important that a comprehensive study is done to understand the mating phenomenon of both. A good linking between rubber and metal substrate is governed by surface pretreatment. Various methodologies such as mechanical and chemical are adopted for the same. This paper aims to present a comparative study as to which surface pretreatment has an edge over other techniques in terms of separation force required to break the bonding between the two parts. The study also presents a cost comparison between the techniques so that the best possible technique can be put to use in the commercial vehicle industry.

Electric vehicles have a limitation of limited range and long charging time. Energy optimization plays a very crucial role in determining the range of an electric vehicle. The innovative system proposed here gives the opportunity to reduce energy wastage and efficiently direct the electrical energy to improve the driving range of a 9 meter AC electric bus. The high voltage air conditioner unit alone consumes more than 40% of the electrical energy stored in the traction battery which reduces the driving range of the electric bus drastically. The proposed system optimizes the air conditioner utilization to direct cool air only in areas where passengers are present. Buses do not always run on full capacity, when there are less number of people in the bus the system detects the locations of the passengers using sensors and occupant detection algorithm, this enables the controller to identify the areas where cooling has to be focused and where cooling can be reduced or stopped.

This paper focuses on partial encapsulation technique for reducing air-borne noise from the rocker cover of a commercial vehicle diesel engine. Due to increasing awareness, customers demand for improvised NVH (Noise Vibration and Harshness) performance in modern day vehicles. Better NVH performance implies better comfort for passengers as well as vehicle operator. This further increases the driver up time due to reduced driver fatigue. In order to improve NVH performance of existing vehicle and observe different noise and vibration zones, detailed noise and vibration mapping was carried out on one of our vehicle platform. It is observed that engine noise is one of the major contributors for interior noise, apart from road inputs etc.

In today’s automobile industry refined NVH performance is a key feature and of high importance governing occupant comfort and overall quality impression of vehicle. In this paper interior noise and vibration measurement is done on one of the light truck and few dominant low frequency noise booms were observed in operation range. Modal analysis was done for the cabin at virtual as well as experimental level and few modes were found close to these noise booms. Vibrations were measured across the cabin mounts and it was found that the isolation of front mounts is not effective at lower frequencies. Taking this as an input, the mount design was modified to shift the natural frequency and hence improve the isolation behavior at the lowest dominant frequency. This was followed by static and dynamic measurement of the mounts at test rig level to characterize the dynamic performance and stiffness conclusion.

BSIV implementation for commercial vehicle in pans India effectively from April 2017. It’s very challenging job for performance and emission engineer to meet engine performance & fuel economy with stringent emission norms for high power and torque density HD diesel engine. In Altitude, lack of air availability & combustion energy passes by mechanical waste gate, lead to lower boost at partial load in waste gate region; which in turn leads to poor engine performance & fuel efficiency and higher turbo speed. To control the turbocharger design speed limit various methodologies adopted like engine derating or optimizing the combustion parameters leads to poor vehicle performance. Combustion parameter optimsation is having limited scope for turbocharger speed control.

With rising concerns on internal combustion engine noise levels in commercial vehicles, it is necessary to attenuate noises present in specific frequency bands. This can be achieved with the implementation of a quarter wave tube on the present exhaust system. Historically such passive attenuators have been efficient only at specific engine speeds and exhaust gas temperatures. A new folded adaptive quarter wave tube design is proposed here which can give significant noise attenuation at various engine operating conditions. The proposed design eliminates the requirement of complex electronic actuating mechanisms for the adaptive quarter wave tubes and replaces the same by perforated diaphragms and adjustable end plates, which are more robust and effective. The module can replace the turbo S-flow single chambered muffler which is installed on most of the commercial vehicles. A design is conceptualized and developed using CAD tools.

Present day truck cab suspension comprises fully floating linkage type cab suspension to facilitate ride comfort. Fully floating cab has certain limitations in terms of stability of cab in dynamic articulations during vehicle running especially in off-road terrain applications. Presence on linkages leads to more wear and tear of joints and bushes which will in turn provide detrimental effect on vibration levels of cab that affects ride comfort for occupants. There is a dire need to develop a system that provides improvement in lateral and vertical stability of cab without compromising ride comfort of occupants. Durability of the product also to be met till life of vehicle. Anti-Vibration Stability Cab Mount is an unsymmetrical mount designed by compounding of elastomeric(rubber) metal bonded outer sleeves sandwiched between multistage inner mount bonded on aluminum casing. Cabin front supports are hinged to mount along with housing providing proper alignment to cab after assembly.

Vehicle life and performance is affected by many factors when in use. The most influential being the vibrations generated especially when the vehicle is in motion. These vibrations are directly experienced by the driver, whose performance goes down, if under continuous influence of these vibrations. This increases the fatigue and greatly reduces the return on investment done by the customer. There are two major sources of vibrations, the engine and the road on which the vehicle moves. To prevent such issues engine mounts are used in vehicles, which may seem simple but perform a critical role, of providing comfort to the driver. Therefore, it becomes important that thoroughly designed and examined mounts are being used in the vehicle. This paper focuses on the methodology to be followed for design and validation of an engine mount used in heavy duty vehicles.

Seats are one of the critical component of school bus for children’s comfort & safety. Seat foam thickness, its shape, cushion width & seat height will play a vital role in comfort. Fatigue is the common cause due to uncomfortable seating and it is due to only one type of seat available in school buses to accommodate different height children. (here different height means; schools have children from class nursery to senior secondary). Fatigue will cause impact on children’s health & overall development. The topic was chosen because of increasing concerns in children’s comfort & safety in school buses. In existing design, standard seat with cushion height from bus floor is 450mm. In this case, it’s only suitable for children height of 4.5 feet to 5.5 feet. Ergonomically, it is very difficult to climb on the seat for range of children height from 3 feet to 4feet.

In the current landscape of commercial vehicle industry, fuel economy is one of the major parameter for fleet owner’s profitability as well as greenhouse gasses emission. Less fuel efficiency results in more fuel consumption; use of conventional fuel in engines also makes environment polluted. The rapid growth in fuel prices has led to the demand for technologies that can improve the fuel efficiency of the vehicle. Phase change material (PCMs) for Thermal energy storage system (TES) is one of the specific technologies that not only can conserve energy to a large extent but also can reduce emission as well as the dependency on convention fuel. There is a great variety of PCMs that can be used for the extensive range of temperatures, making them attractive in a number of applications in automobiles.

The Mounting system of component plays a major role in determining the structural durability, compatibility and synchronization of the systems with respect to each other. The major function of Engine mounts is to isolate the engine from the chassis and to align the power-train system of vehicle according to needs. Here we exclusively deal with the failure case of a Heavy duty commercial vehicle Engine Mounts and its optimization. We do formulate a theoretical calculation for the estimation of engine loads, Center of Gravity (C.G) and characteristics of existing engine mount followed by a failure root cause analysis based on design and transmissibility parameters. This is then correlated with data from Computed Aided Engineering and Matlab for analysis of the existing model which is compared to the experimental transmissibility from Road load data Acquisition (RLDA). This is to validate the conditions and propose optimizations to reduce critical failures.

In an automobile, main function of the steering system is to allow the driver to guide the vehicle on a desired course. Steering system consists of various components & linkages. Using these linkages, the torque from steering wheel is transferred to tyre which results in turning of the vehicle. Over the life of vehicle, these steering components are subjected to various loading conditions. As steering components are safety critical parts in the vehicle, therefore they should not fail while running because it will cause vehicle breakdown. In commercial vehicle segment, vehicle breakdown means delay in freight delivery which results in huge loss to costumer. Therefore, while designing steering components one should consider all the possible loadings condition those are possible. But, it can’t be done through theoretical calculation. Therefore, physical tests have to be carried out to validate design of steering system, which is very costly & time-consuming process.

At the time of invention of road coaches, the vehicle consisted only of an axle with wheels and a body attached. Smooth roads were built for a better ride comfort however they were not consistent. The road coaches were too bumpy and uncomfortable for the passenger along with the driver who was not able to control the vehicle. That's why the engineers had to shift their attention to the suspension system for a better ride comfort and handling. The technology has advanced with time so as the suspension system. Rubber ended type leaf spring is one of the suspension system types available in the industry. The main function of a suspension in order of importance is as below: 1 Acts as a cushioning device ensuring the comfort of the driver and passengers; 2 Maximizes the contact between the tires and the road surface to provide steering stability with good handling; 3 Protects the vehicle itself and any cargo or luggage from damage and wear.

In the modern era of commercial vehicle industry, passenger and driver comfort is one of the major parameters that improves vehicle running time which leads to fleet owner’s profitability. Air conditioning system is one such system whose primary function is to provide the required cooling inside the cabin in hot weather conditions. An Air-conditioned truck cabin creates a comfortable environment for the driver which increases his efficiency and reduces fatigue. An AC compressor consumes power directly from the engine affecting fuel economy and vehicle performance. With ever increasing demand for energy efficient systems and thermal comfort in automobiles, AC systems should be able to deliver the required cooling performance with minimum power consumption. Therefore, reducing AC power consumption in vehicles is one of the key challenges faced by climate control engineers.

Diesel exhaust is a complex mixture of combustion products of diesel fuel, and the exact composition of the mixture depends on the nature of the engine, operating conditions, lubricating oil, additives, emission control system, combustion parameters and fuel composition. In a diesel engine, NOx (NO & NO2) and PM (Particulate Matter) are the most critical constituents for the emission legislation. In order to control the PM emission of diesel engine and comply with increasingly stringent exhaust legislation, more information is required on the components and genesis of PM. In general, PM from diesel engines is classified into two fractions: Insoluble Organic Fraction (ISOF) and Soluble Organic Fraction (SOF). In this experimental study, a series of 13 mode ESC cycle were run on a light duty diesel engine after optimization of combustion parameters (Injection Pressure, Injection Timing, Multiple Injections, EGR rate, etc) in successive tests and PM component was analyzed.

The hybrid structure of Engine Mounts made of rubber casing with cast iron reinforcing. Use of two materials made it unique both in application and testing. The rubber provides damping for engine vibrations and the cast iron provides necessary strengthening to hold the heavy engine in place. In this research paper the FEA (Finite Element Method) methodology is being discussed to evaluate and optimize the design analysis to enhance overall engine mount capacity. The existing and modified designs are validated and considerable improvement is being observed in modified design in physical testing. Accurate modeling of engine mounts assembly is presented in this paper. FEA analysis results have good correlation with physical validation for both designs. Impact of design parameters of rubber mounts has been presented.

An efficient after treatment technique is driven by the need to maintain strict emission norms for heavy-duty and medium-duty ground vehicles. SCR being an advanced active emission technology system for diesel engine, is one of the most cost-effective and fuel-efficient technologies available for complying with the stringent NOx emission legislations. The design of the SCR system involves catalyst selection, complex controller development like urea dosing strategy and the interaction between engine setup and after treatment system. For this purpose, the SCR model must be computationally efficient to evaluate the complete efficiency along with to take care for the NH3 slip also. The SCR model was prepared with respect to SCR inlet temperature and ratio of NOx and ammonia to study the behavior of NOx conversion efficiency keeping consideration of NH3 slip also required for optimizing the calibration.

Market driven competition in global trade and urgency for controlling the atmospheric air pollution are the twin forces, which have urged Indian automobile industries to catch up with the international emission norms. Improvement in the fuel efficiency of the vehicles is one way to bind to these stringent norms. It is experimentally proven that almost 40% of the available useful engine power is being consumed to overcome the drag resistance and around 45% to overcome the tire rolling resistance of the vehicle. This as evidence provides a huge scope to investigate the influence of aerodynamic drag and rolling resistances on the fuel consumption of a commercial vehicle. The present work is a numerical study on the influence of aerodynamic drag resistance on the fuel consumption of a commercial passenger bus. The commercial Computational Fluid Dynamics (CFD) tool FLUENT™ is used as a virtual analysis tool to estimate the drag coefficient of the bus.

Ever-increasing operational cost, reducing profit margins & increase in competition, it is of upmost significance for fleet owners & drivers to opt for a vehicle having maximum uptime. OEM's are under immense pressure to design & develop vehicles/subsystems which are reliable enough to minimize downtime & withstand heavy overloading plus extreme operating conditions especially tippers. Vehicle systems like Wheel end (hub, bearing, and grease) which are designed & packaged according to a very stringent envelop & operate as a closed system facing all the extremities of operating conditions. This undoubtly make them prone to no. of failure modes which are resulting in vehicle unplanned stoppages, so any failure mode related to the same must be taken care with utmost importance. In commercial vehicles the bearing outer cup is in interference fit with the hub. These bearings of wheel hub have to be maintained at the wheel end play of few microns.

The main emphasis for a commercial vehicle design which was focused on fuel-economy and durability does not fulfill the increasing customer expectations anymore. Commercial vehicle designers need to focus on other vehicle aspects such as steering, ride comfort, NVH, braking, ergonomics and aesthetics in order to provide car like perception to truck, bus drivers and passengers during long distance drives. Powertrain mounting system must perform many functions. First and foremost, the mounting system must maintain & control the overall motion of the powertrain, to restrict its envelope reasonably, thereby avoiding damage to any vehicle component from the potential impact. This requires the mount to be stiff. Second the mount must provide good vibration isolation to have a comfortable ride to the vehicle occupant. This requires the mount to be soft.