Criteria

Text:
Author:
Display:

Results

Viewing 1 to 18 of 18
2012-09-24
Technical Paper
2012-01-2031
Zhao Weiqiang, Changfu Zong, Hongyu Zheng, Huaji Wang, Shengnan Yang
The quality of the brake system is a significant safety factor in commercial vehicles on the roads. With the development of automobile technology, the single function ABS system didn't meet active safety requirements of the user. The Electronically Controlled Brake System (EBS) system will replace the ABS system to become the standard safety equipment of commercial vehicles in the near future. EBS can be said an enhanced ABS system, it contains load sensor, brake valve sensor and pressure sensor of chamber, etc, and it is more advantages than ABS. This paper describes a flexible integrated test bench for ABS/EBS Electronic Control Unit (ECU) based on Hardware-In-the-Loop (HIL) simulation technique. It consists of most commercial vehicle pneumatic braking system components (from brake pedal valve, brake caliper to brake chambers), and uses the dSPACE real-time simulation system to communicate to the hardware I/O interface.
2015-09-29
Technical Paper
2015-01-2841
Hongyu Zheng, Shenao Ma
Abstract This paper establishes a brake pedal model for braking intention identification, using the structural features of electronic braking system and selecting the proper parameters. A three-dimensional model is built that the input parameters are pedal displacement and pedal displacement change rate, and the output parameter is braking intensity. The relationship between the driver braking operation and braking intention are designed. A hardware-in-the-loop test bench experiment has been taken under several skilled drivers to practice the established the brake pedal model with the operation data during the braking. Thus, it results a model indicating the braking intention by braking operation that means effectively improve the braking comfort and applies to the research of electronic braking system of commercial vehicle.
2015-09-29
Technical Paper
2015-01-2842
Hongyu Zheng, Jinghuan Hu, Shenao Ma
Abstract Heavy vehicles have the characteristics of with high center of gravity position, large weight and volume, wheelbase is too narrow relative to the body height and so on, so that they always prone to rollover. In response to the above heavy security problems of heavy vehicle in running process, this paper mainly analyzes roll stability and yaw stability mechanism of heavy vehicles and studies the influence of vehicle parameters on stability by establishing the vehicle dynamics model. At the same time, this paper focuses on heavy vehicles stability control methods based on simulation and differential braking technology. At last, verify the effect of heavy vehicle stability control by computer simulation. The results shows that self-developed stability control algorithm can control vehicle stability effectively, so that the heavy vehicles instability can be avoided, the vehicle driving safety and braking stability are improved.
2015-09-29
Technical Paper
2015-01-2729
Guoying Chen, Lei He, Hongyu Zheng, Yaohua Guo
Abstract For the vehicles equipped with Electric Power Steering (EPS) system, the friction and damping effect brought by assisted motor and worm gear mechanism influence the return ability and handing stability. In order to eliminate the impacts, it is necessary to add return-to-center control in EPS control strategy. This paper proposes a practical active return-to-center control strategy with steering wheel angle signals based on return state identification. In the strategy, the return state of the steering system is identified quickly according to the two signals steering wheel angle velocity and steering wheel torque. Only under return state, a double closed-loop PID control strategy is carried out to calculate a compensation current to improve the return ability. For validating the proposed strategy, a fine EPS model including BLDC assisted motor is built based on carsim and simulink co-simulation platform.
2014-09-30
Technical Paper
2014-01-2285
Dong Zhang, Changfu Zong, Ying Wan, Hongyu Zheng, Wei-qiang Zhao
Abstract Electronic braking system (EBS) of commercial vehicle is developed based on Anti-lock Braking System (ABS), for the purpose of enhancing the braking performance. Based on the previous study, this paper aims at the development and research on the control strategy of advanced electronic braking system for commercial vehicle, which mainly includes braking force distribution and multiple targets control strategy. In the study of braking force distribution control strategy, the mass of vehicle and the axle loads will be calculated dynamically and the braking force of each wheel will be distributed regarding to the axle loads. The braking intention recognition takes the brake pad wear into account when braking uncritically, so it can detect a difference in the pads between the front and the rear axles. The brake assist strategy supports the driver during emergency braking and the braking distance is shortened by the reduction of the braking system response time.
2014-09-30
Technical Paper
2014-01-2287
Hongyu Zheng, Linlin Wang
Abstract A brake pad wear control algorithm used under non-emergency braking conditions is proposed to reduce the difference in brake pad wear between the front and rear axles caused by the difference in brakes and braking force. According to the adhesion state of the pad wear, the control algorithm adjusted the braking force distribution ratio of front and rear wheel that balanced adhesion pad wear value. Computer co-simulations of braking with Trucksim and Matlab/Simulink using vehicle models with equal brake pad wear, greater wear on the front axle and greater wear on the rear axle respectively is performed. The computation simulation results show that meet the brake force distribution system regulatory requirements and total vehicle braking force unchanged.
2013-11-27
Technical Paper
2013-01-2818
Buyang Zhang, Changfu Zong, Hongyu Zheng, Hanqing zhao, Yang Liu
The commercial vehicle is widely used in the overland transport. A prediction is given on the 9th annual China automotive industry forum that the number of the global commercial vehicles will reach eight million by the year of 2016. However, since the distance between its gravity centre and the ground is larger than that of the passenger vehicle, considering its comparatively short wheelbase, the rollover accident, which is fatal to the drivers and always makes enormous loss of merchandises, easily occurs in the case of commercial vehicles. As the number of the commercial vehicle is increasing fast, the accidents will occur more frequently, the losses will be increasingly enormous. To solve the problem, many researches about rollover early warning systems have been done. In most cases, it is assumed that the references of the vehicle are given.
2013-11-27
Technical Paper
2013-01-2828
Minghui Ren, Changfu Zong, Ying Wan, Mingxu Duan, Hongyu Zheng
The hybrid electric city bus, which consists of the electric motor and battery, is obviously different from the traditional buses. This paper focuses on optimizing the characteristics of the automatic mechanical transmission in hybrid electric city bus and does the following studies: firstly, in order to reduce the fuel consumption, the transmission ratio and some structural parameters are optimized with CRUISE software; secondly, the volume and weight of the transmission structure is reduced and optimized by numerical optimization approach, with the limitation of the structural reliability.
2013-11-27
Technical Paper
2013-01-2795
Jongchol Han, Zhao Weiqiang, Changfu Zong, Hongyu Zheng
The simulation of electro-pneumatic components used in brake systems of commercial vehicles is of great importance in order to understand their characteristics for developing a control logic and improve the braking performance. As the goal of improving the performance of the commercial vehicle pneumatic EBS(Electronically controlled Braking System), static and dynamic characteristics of proportional relay valve for commercial vehicle pneumatic EBS have been simulated by using MATLAB/Simulink environment and validated by testing on hardware-in-the-loop test bench focused on its pressure hysteresis characteristic. The simulation and test results show that the mathematic model for proportional relay valve characteristics is reasonable and reliable, and this simulation tool can be used for research and developing of pneumatic EBS system for commercial vehicle effectively.
2014-09-30
Technical Paper
2014-01-2371
Minghui Ren, Ying Wan, Hongyu Zheng
For city buses, especially hybrid electric buses, the requirements for the fuel economy and low noises are stricter, comparing with the momentum quality. Since hybrid electric buses sometimes run without the engine, the noises that the transmission makes become the major type. To get better fuel economy and lower noises, this paper focuses on optimizing the characteristics of the automatic mechanical transmission (AMT) in a hybrid electric city bus, and the studies are done as follows. Firstly, in order to reduce the fuel consumption, the transmission ratios are optimized by the co-simulation and optimization in CRUISE and MATLAB, with the limitation of the quality of driving momentum. Secondly, for the purpose of lightweight and lower transmission noise, multi-objective optimization based on reliability is applied in transmission geometric optimization design, the objective function are the smallest volume and the biggest transmission gear contact ratio of the transmission.
2013-04-08
Technical Paper
2013-01-0411
Rong He, Hongyu Zheng, Changfu Zong
In order to improve the braking energy recovery, a parallel hybrid electric bus simulation model with electric braking system (EBS) was established by co-simulation platform for the TruckSim and Matlab/Simulink in this paper. EBS makes the front and rear shaft braking force arbitrarily distributed, which is more effective to improve the rate of energy recovery and the braking stability. A braking force distribution algorithm for hybrid electric bus based on EBS was designed in this paper. Under the premise to meet the driver's needs and the ECE regulations, this braking force distribution method focuses on making the braking force distribute to the drive shaft to a maximum extent, so as to obtain the maximum energy recovery rate by the utilization of the motor regenerative braking. At last, the simulation in different operating conditions was used to analyze the braking energy utilization and the braking performance based on the simulation model.
2015-09-29
Technical Paper
2015-01-2742
Linlin Wang, Hongyu Zheng, Changfu Zong, Yuchao Chen
Abstract Aiming at estimating the vehicle mass and the position of center of gravity, an on-line two-stage estimator, based on the recursive least square method, is proposed for buses in this paper. Accurate information of the center of gravity position is crucial to vehicle control, especially for buses whose center of gravity position can be varied substantially because of the payload onboard. Considering that the buses start and stop frequently, the first stage of the estimator determines the bus total mass during acceleration, and the second stage utilizes the recursive least-square methods to estimate the position of the center of gravity during braking. The proposed estimator can be validated by the co-simulation with MATLAB/Simulink and TruckSim software, simulation results exhibit good convergence and stability, so the center of gravity position can be estimated through the proposed method in a certain accuracy range.
2014-09-30
Technical Paper
2014-01-2385
Linlin Wang, Hongyu Zheng
The paper focus on enhancing the braking safety and improving the braking performance of the tractor/trailer vehicle. A slip-rate-based braking force distribution algorithm is proposed for the electronic braking system of tractor/trailer combination vehicle. The algorithm controls the slip-rates of the tractor's rear wheels and the semi-trailer's wheels changing with the slip-rate of tractor's front wheels, making tractor's front wheels lock up ahead of the tractor's rear wheels and the semi-trailer's wheels. The algorithm protects the combination vehicle from jackknifing and swing, guaranteeing that the combination vehicle has better driving stability and steering capability. The algorithm can be tested by co-simulation with MATLAB/Simulink and TruckSim software both on high adhesion and low adhesion roads.
2014-09-30
Journal Article
2014-01-2387
Hongyu Zheng, Linlin Wang
Abstract The active safety and stability of tractor and trailer (heavy-duty vehicle) have becoming big concern among the road transportation industry. The purpose of this paper is to specify the research differential braking force distribution control algorithm to improve braking safety of heavy-duty vehicle. The ideal braking force of each wheel axle should be proportional to vertical load of vehicle that is also related to the road adhesion coefficient, the load and the braking intensity. Reasonable braking force distribution can enhance its braking stability and shorten the braking distance by making full use of the road adhesion condition of each wheel. A braking force distribution algorithm is proposed, in which the objective braking force change with the axle load of vehicle.
2014-09-30
Journal Article
2014-01-2382
Hongyu Zheng, Linlin Wang
Abstract At present, the active safety and stability of heavy vehicles have becoming big concern among the road transportation industry. The purpose of this paper is to specify the research stability and safety of heavy vehicles those set up the accurate and reliable dynamic vehicle reference model and search the method to improve the stability and safety of tractor and semitrailer. A Multi-objective control algorithm was studied to differential braking based on linear quadratic regulator (LQR) control method. Simulation results show that the multi-objective control algorithm can effectively improve the vehicle driving stability and safety.
2013-09-24
Technical Paper
2013-01-2372
Zongyu Liu, Hongyu Zheng, Wenkai Xu, Zeyang Yu
Aiming at achieving the economy and safety of downhill brake process (running downward along a long slope at a constant velocity) of commercial vehicles, an integrated control strategy of the main brake system and auxiliary brake systems is proposed. Based on Electronic Controlled Braking System (EBS), the strategy distributes braking force to each brake system and each axle according to the thermodynamic feature of them and the wear loss of each brake lining, in order to achieve economy at the premise of safety. A simulation is conducted based on MATLAB/Simulink and TruckSim. Simulation results show that the strategy proposed could control the temperature of each brake system at a rational value, and the balanced wear loss of brake linings is facilitated, thus, the safety and economy of downhill brake is ensured.
2013-04-08
Technical Paper
2013-01-0418
Zongyu Liu, Hongyu Zheng, Wenkai Xu
Taking a good longitudinal braking performance on flat and level road of tractor and semi-trailer combination as a target, in order to achieve an ideal braking force distribution among axles, while the vehicle deceleration is just depend on the driver's intention, not affected by the variation of semi-trailer mass, the paper proposes a model based vehicle mass identification and braking force distribution strategy. The strategy identifies the driver's braking intention via braking pedal, estimates semi-trailer's mass during the building process of braking pressure in brake chamber, distributes braking force among axles by using the estimated mass. And a double closed-loop regulation of the vehicle deceleration and utilization adhesion coefficient of each axle is presented, in order to eliminate the bad effect of mass estimation error, and enhance the robustness of the whole algorithm. A simulation is conducted by utilizing MATLAB/Simulink and TruckSim.
2015-09-29
Technical Paper
2015-01-2723
Yaning Han, Hongyu Zheng, Ying Wan, Changfu Zong
Abstract Electro-hydraulic power steering system (EHPS) maintains the advantages of Hydraulic power steering system (HPS) and Electric power steering system (EPS).It is even more superior than this two. In the foreseeable future, this system will have a certain development space. Assistant characters analysis was carried out in this paper. Control strategy based on steering states and feedback control strategy were designed too. Besides, aiming at the emergency steering conditions, steering angular velocity additional controlling strategy was brought out. Under emergency steering conditions, steering angular velocity additional controlling strategy will be applied. Additional steering moment will be calculated to ensure the assistant follow steering rapidly.
Viewing 1 to 18 of 18

    Filter

    • Range:
      to:
    • Year: