Criteria

Text:
Display:

Results

Viewing 1 to 30 of 40
CURRENT
2016-11-15
Standard
J1281_201611
This SAE Standard establishes the procedure for determining the operator duty cycle sound pressure level Lodc to which operators of powered recreational craft up to 24 m in length are exposed during typical operation as determined by marine engine duty cycle studies. This document describes the instrumentation, the required calibration procedures, the test site, the specifications for “standard craft”, the craft operating conditions, microphone positioning, test procedure, engine speeds for each of the Duty Cycle modes and the formula and table for calculating the Duty Cycle operator ear sound pressure level. This document is subject to change to keep pace with technical advances as well as other international standards and practices. Changes in this Revision: The sound pressure level measurements performed while applying this document are based on the Five-Mode Marine Engine Duty Cycle instead of a single engine speed.
HISTORICAL
1985-03-01
Standard
J1281_198503
This SAE Recommended Practice establishes the procedure for assessing operator sound level exposure for pleasure motorboats under 20 m (65 ft) in length when operated under typical conditions, and describes the instrumentation, test site, and boat operation for making valid measurements.
CURRENT
2015-05-12
Standard
J1449_201505
This SAE Recommended Practice specifies graphic symbols for operator controls, gauges, tell-tales, indicators, instructions, and warning against risks in small craft and for engines and other equipment intended to be used in small craft.
HISTORICAL
1987-02-01
Standard
J1449_198702
This SAE Recommended Practice specifies graphic symbols for operator controls, gauges, tell-tales, indicators, instructions, and warning against risks in small craft and for engines and other equipment intended to be used in small craft.
HISTORICAL
2002-03-15
Standard
J1449_200203
This SAE Recommended Practice specifies graphic symbols for operator controls, gauges, tell-tales, indicators, instructions, and warning against risks in small craft and for engines and other equipment intended to be used in small craft.
HISTORICAL
1998-07-01
Standard
J1378_199807
This SAE Recommended Practice establishes minimum requirements for electric hourmeters for general vehicular applications.
CURRENT
2011-03-08
Standard
J1378_201103
This SAE Recommended Practice establishes minimum requirements for electric hourmeters for general vehicular applications.
HISTORICAL
2001-02-14
Standard
J961_200102
The purpose of this SAE Recommended Practice is to provide guides toward standard conditions for operating marine engine throttles (gasoline or diesel) where push-pull cable control is applicable. For control cable information see SAE J917.
HISTORICAL
1980-06-01
Standard
J755_198006
This SAE Standard specifies basic tolerances and dimension for inboard propeller-shaft ends, propeller hubs and keyways for shaft sizes 3/4 in (19 mm) through 8 in (203 mm).
CURRENT
2015-05-12
Standard
J755_201505
This SAE Standard specifies basic tolerances and dimensions for inboard propeller-shaft ends, propeller hubs and keyways for shaft sizes 3/4 in (19 mm) through 8 in (203 mm).
CURRENT
2005-04-25
Standard
J3046/1_200504
This part of ISO 3046 specifies standard reference conditions and methods of declaring the power, fuel consumption, lubricating oil consumption, and test methods for reciprocating internal combustion (RIC) engines in commercial production using liquid or gaseous fuels. Where necessary, individual requirements are given for particular engine applications. This part of ISO 3046 covers RIC engines for land, rail-traction, and marine use, excluding engines used to propel agricultural tractors, road vehicles, and aircraft. This part of ISO 3046 may be applied to engines used to propel road construction and earthmoving machines, industrial trucks, and for other applications where no suitable International Standard for these engines exists. This part of ISO 3046 may be applied to tests on a test bed at the manufacturer's works and to tests on site.
HISTORICAL
2004-07-27
Standard
J2005_200407
This SAE Recommended Practice establishes the procedure for determining if pleasure motorboats have effective exhaust muffling means when operating in the stationary mode. It is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document specifies guidelines for stationary sound level measurements for boats with above-water exhaust systems.
CURRENT
2011-04-01
Standard
J2005_201104
This SAE Recommended Practice establishes the procedure for determining if recreational motorboats have effective exhaust muffling means when operating in the stationary mode. It is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances.
HISTORICAL
1981-08-01
Standard
J756_198108
This SAE Standard covers propeller shaft couplings for use with propeller shafts up to 3 inches outside diameter. To provide design guidance that results in dimensional interchangeability of marine propeller-shaft couplings within the scope of this standard.
CURRENT
2005-04-05
Standard
J756_200504
This SAE Standard covers propeller shaft couplings for use with propeller shafts up to 3 inches outside diameter. To provide design guidance that results in dimensional interchangeability of marine propeller-shaft couplings within the scope of this standard.
CURRENT
2014-09-09
Standard
J917_201409
This SAE Standard covers dimensions, performance parameters and nomenclature of a push-pull control cable used in inboard marine throttle and shift applications.
HISTORICAL
2004-12-15
Standard
J917_200412
This SAE Standard covers dimensions and nomenclature of a push-pull control cable used in inboard marine engine applications. The dimensions are representative of existing design practice prevalent in the industry. The flexible push-pull cable is a common motion transfer device for the remote operation of the throttle and clutch levers (hydraulically applied clutches) on marine propulsion units. Satisfactory function of remote controls depend upon observing the limitations of this cable and providing adequate connection to the propulsion unit. This standard, therefore, establishes nomenclature, dimensions, and installation recommendations for marine push-pull control cables.
HISTORICAL
2003-09-08
Standard
J1970_200309
This SAE Recommended Practice establishes the procedure for measuring the sound level of recreational motorboats at a position on the shore under conditions other than stationary mode operation. It is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. Purpose This document specifies guidelines for sound level measurements made from the shoreline of recreational boating areas and is intended for recreational motorboats only.
CURRENT
2011-02-18
Standard
J1970_201102
This SAE Recommended Practice establishes the procedure for measuring the sound level of recreational motorboats in the vicinity of a shore bordering any recreational boating area during which time a boat is operating under conditions other than stationary mode operation. It is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances.
CURRENT
2011-10-27
Standard
J1191_201110
This Standard covers the requirements for all marine inboard and outboard gasoline engine ignition assemblies and components.
CURRENT
2016-04-06
Standard
J1228_201604
This SAE Standard specifies the test requirements in addition to those given in ISO 3046-1 for determining the power, at a single point or as a power curve, of marine propulsion engines or systems for recreational craft and other small craft using similar propulsion equipment of less than 24 m length of the hull. It also provides the means for documenting and checking the declared (rated) power published by the manufacturer.
CURRENT
2016-11-15
Standard
J1294_201611
This SAE Recommended Practice covers distributors used on marine engines. NOTE: This includes devices referred to as high voltage switches used for distributing high voltage to the appropriate spark plugs but does not contain any crank position sensing function.
CURRENT
2017-03-22
Standard
J1286_201703
This method covers electric outboards that are rated in terms of static thrust.
HISTORICAL
2009-05-04
Standard
J1286_200905
This method covers all electric outboards.
CURRENT
2013-11-13
Standard
J1320_201311
This SAE Recommended Practice covers the requirements for switches used in marine applications both under and over 50 V.
CURRENT
2013-05-16
Standard
J1428_201305
This recommended practice covers the requirements of magnetic or thermal circuit breakers for use in marine applications for 50 V DC or less.
2017-07-20
WIP Standard
J1928
This SAE Standard covers the minimum requirements for design, construction, and testing of devices to prevent the propagation of backfire flame from within the gasoline engine to the surrounding atmosphere.
HISTORICAL
1989-06-01
Standard
J1928_198906
This SAE Standard covers the minimum requirements for design, construction, and testing of devices to prevent the propagation of backfire flame from within the gasoline engine to the surrounding atmosphere.
HISTORICAL
1991-10-01
Standard
J1928_199110
This SAE Standard covers the minimum requirements for design, construction, and testing of devices to prevent the propagation of backfire flame from within the gasoline engine to the surrounding atmosphere.
CURRENT
2012-01-06
Standard
J1928_201201
This SAE Standard covers the minimum requirements for design, construction, and testing of devices to prevent the propagation of backfire flame from within the gasoline engine to the surrounding atmosphere.
Viewing 1 to 30 of 40