Criteria

Text:
Display:

Results

Viewing 1 to 30 of 58
2013-03-11
WIP Standard
J3036
To provide uniform laboratory procedures and radial/lateral load pairs for biaxial fatigue testing of disc wheel intended for normal highway use on trucks, buses, and trailers applicable for the North America market. Load cases considered include steer, drive, and trailer vehicle positions. The radial/lateral load pairs are not specific to one particular vehicle or OEM manufacturer.
HISTORICAL
2008-07-17
Standard
J2224_200807
This SAE Information Report lists the symbols used by suppliers of truck, trailer, and bus wheel seals to identify their products. These symbols appear on seals and packaging.
HISTORICAL
2002-05-31
Standard
J2224_200205
This SAE Information Report lists the symbols used by suppliers of truck, trailer, and bus wheel seals to identify their products. These symbols appear on seals and packaging. The purpose of this document is to provide users of truck, trailer, and bus wheel seals a means of identifying the suppliers of all such components by use of the symbology utilized by the suppliers on their components and packaging.
CURRENT
2015-11-19
Standard
J2224_201511
This SAE Information Report lists the symbols used by suppliers of truck, trailer, and bus wheel seals to identify their products. These symbols appear on seals and packaging. 1.1 Purpose The purpose of this document is to provide users of truck, trailer, and bus wheel seals a means of identifying the suppliers of all such components by use of the symbology utilized by the suppliers on their components and packaging.
HISTORICAL
2001-06-12
Standard
J2133_200106
This SAE Recommended Practice provides for standardized disc wheel radial runout low point marking. This marking is used for match-mounting tires on wheels to minimize assembly radial force variation. It applies to tubeless 15 degree drop center disc wheels for use on class 5, 6, 7, and 8 commercial vehicles.
CURRENT
2015-02-20
Standard
J1671_201502
This recommended practice contains dimensions and tolerances for outboard mounted brake drums and disc wheel hubs in the interface areas. This recommended practice is intended for outboard mounted brake drums and disc wheel hubs commonly used on class 7 and 8 commercial vehicles. Included are SAE J694 mounting systems II, III, IV, XIV, and X. Special and less common applications are not covered.
CURRENT
2012-03-15
Standard
J1730_201203
This SAE Recommended Practice establishes the Antilock Brake System [ABS] sensor interface and envelope dimensions for standardizing the location of the ABS rings mounted on the inner end of spoke wheels, hubs and hub-rotor assemblies on the following axle designations. FF FL FC FH L R U W N P
HISTORICAL
2006-05-22
Standard
J1671_200605
This SAE Recommended Practice contains dimensions and tolerances for outboard mounted brake drums and disc wheel hubs in the interface areas. The geometric features described in this document are shown at true position. This document is intended for outboard mounted brake drums and disc wheel hubs used on Class 7 and 8 commercial vehicles. Special and less common applications are not covered. This document defines and documents the dimensions and tolerances necessary to maintain interchangeability in the interface areas.
HISTORICAL
1984-07-01
Standard
J179_198407
This SAE Recommended Practice establishes uniform minimum labeling for disc wheels and demountable rims used in truck, bus, and trailer applications.
HISTORICAL
1970-10-01
Standard
J179A_197010
This SAE Recommended Practice establishes uniform minimum labeling for disc wheels and demountable rims used in truck, bus, and trailer applications.
HISTORICAL
1970-06-01
Standard
J179_197006
This SAE Recommended Practice establishes uniform minimum labeling for disc wheels and demountable rims used in truck, bus, and trailer applications.
CURRENT
2013-05-23
Standard
J179_201305
This SAE Recommended Practice establishes uniform minimum labeling for disc wheels and demountable rims used in truck, bus, and trailer applications.
HISTORICAL
2012-09-27
Standard
J179_201209
This SAE Recommended Practice establishes uniform minimum labeling for disc wheels and demountable rims used in truck, bus, and trailer applications.
HISTORICAL
2011-04-14
Standard
J179_201104
This SAE Recommended Practice establishes uniform minimum labeling for disc wheels and demountable rims used in truck, bus, and trailer applications.
HISTORICAL
2007-02-21
Standard
J179_200702
This SAE Recommended Practice establishes uniform minimum labeling for disc wheels and demountable rims used in truck, bus, and trailer applications.
CURRENT
2014-02-03
Standard
J1842_201402
This SAE Recommended Practice is intended for hubs and spoke wheels used on Class 6, 7, and 8 truck/truck-tractor non-powered front axles, powered and non-powered rear axles and trailer axles, for which bearing setting is manually adjusted. Assemblies using spacers to control bearing preload and endplay may differ in geometry and bearing componentry.
HISTORICAL
2004-11-22
Standard
J1842_200411
This SAE Recommended Practice is intended for hubs and spoke wheels used on Class 7 and 8 truck/truck-tractor nonpowered front axles, powered and nonpowered rear axles, and trailer axles. The purpose of this document is to establish dimensional guidelines to promote a functional standardization of wheel hubs and spoke wheels in the areas of fasteners, bearing cups, seal bore, and axle drive shaft or hub cap attachment. This document is not intended to exclude the use of wheel hub designs which do not meet the dimensional guidelines for use on defined axle configurations.
2017-05-16
WIP Standard
J1842
This SAE Recommended Practice is intended for hubs and spoke wheels used on Class 6, 7, and 8 truck/truck-tractor non-powered front axles, powered and non-powered rear axles and trailer axles, for which bearing setting is manually adjusted. Assemblies using spacers to control bearing preload and endplay may differ in geometry and bearing componentry.
HISTORICAL
2006-12-06
Standard
J2535_200612
This SAE Recommended Practice applies to the four primary, large volume applications in the class 7-8 heavy-duty market place, as specified in SAE J1842: a. "N" trailer axle b. "R" powered rear axle c. "FF / FG" nonpowered front axle d. "P" trailer axle This document applies to on-highway, disc wheel / outboard drum brake applications. It is not applicable to those applications that exceed the GAWR ratings or the load line restrictions listed in columns "A," "B," and "C" of Table 1. Load lines are measured from the inboard bearing cup backface as shown in 3.4. This document establishes preload force values only. The methodology to obtain these force values must be determined by the fastener supplier and/or axle assembler. This document reviews the bearing system. It is NOT intended to prescribe (new or existing) axle and/or hub manufacturers' ratings and/or specifications.
CURRENT
2013-02-11
Standard
J2535_201302
This SAE Recommended Practice applies to the four primary, large volume applications in the class 7-8 heavy-duty market place, as specified in SAE J1842: “N” trailer axle “R” powered rear axle “FF / FG” nonpowered front axle “P” trailer axle This document applies to on-highway applications. It is not applicable to those applications that exceed the GAWR ratings or the load line restrictions listed in columns “A,” “B,” and “C” of Table 1. Load lines are measured from the inboard bearing cup backface as shown in 3.4. This document establishes preload force values only. The methodology to obtain these force values must be determined by the fastener supplier and/or axle assembler. This document reviews the bearing system. It is NOT intended to prescribe (new or existing) axle and/or hub manufacturers’ ratings and/or specifications.
HISTORICAL
1988-09-01
Standard
J694_198809
This SAE Recommended Practice contains dimensions and their tolerances concerning disc wheel to hub or drum interface areas for commercial vehicles and multipurpose passenger vehicles. Stamped disc wheels for single applications and special or less common applications are not covered in this document. This document defines wheel mounting systems and documents the dimensions and tolerances necessary to maintain serviceability, and interchangeability in the interface areas. To be consistent with ISO, it is divided into two sections (I and II). Section I is in concert with ISO 4107, describing mounting systems currently used internationally and nominated for, or included in, the international standard for bolt circle interfaces. Section II records information on current mounting systems also used in North America. Components of different mounting systems with common bolt patterns could be mis-assembled together and cause service problems.
HISTORICAL
2001-02-22
Standard
J694_200102
This SAE Recommended Practice contains dimensions and their tolerances concerning disc wheel to hub or drum interface areas for commercial vehicles and multipurpose passenger vehicles. Stamped disc wheels for single applications and special or less common applications are not covered in this document. Purpose This document defines wheel mounting systems and documents, the dimensions and tolerances necessary to maintain serviceability, and interchangeability in the interface areas. To be consistent with ISO, it is divided into two sections (I & II). Section I is in concert with ISO 4107, describing mounting systems currently used internationally and nominated for, or included in, the international standard for bolt circle interfaces. Section II records information on current mounting systems also used in North America. Components of different mounting systems with common bolt patterns could be mis-assembled together and cause service problems.
CURRENT
2015-05-12
Standard
J694_201505
This SAE Recommended Practice contains dimensions and their tolerances concerning disc wheel to hub or drum interface areas for truck and bus applications. Disc wheels designed only for single wheel applications (not dual wheels) for light trucks and special or less common applications are not covered in this document.
HISTORICAL
2007-06-21
Standard
J694_200706
This SAE Recommended Practice contains dimensions and their tolerances concerning disc wheel to hub or drum interface areas for commercial vehicles and multipurpose passenger vehicles. Stamped disc wheels for single applications and special or less common applications are not covered in this document.
HISTORICAL
1987-06-01
Standard
J851_198706
This SAE Recommended Practice establishes dimensions for wheels for demountable rims, demountable rims, and rim spacers. The dimensions given are those necessary to maintain serviceability and interchangeability of the demountable rims, rim spacers, and wheels for demountable rims. Special and less common applications are not covered in this recommended practice.
HISTORICAL
1988-05-01
Standard
J694_198805
This SAE Recommended Practice contains dimensions and their tolerances concerning disc wheel to hub or drum interface areas for commercial vehicles and multipurpose passenger vehicles. Stamped disc wheels for single applications and special or less common applications are not covered in this document. This document defines wheel mounting systems and documents the dimensions and tolerances necessary to maintain serviceability, and interchangeability in the interface areas. To be consistent with ISO, it is divided into two sections (I and II). Section I is in concert with ISO 4107, describing mounting systems currently used internationally and nominated for, or included in, the international standard for bolt circle interfaces. Section II records information on current mounting systems also used in North America. Components of different mounting systems with common bolt patterns could be mis-assembled together and cause service problems.
HISTORICAL
2001-07-31
Standard
J851_200107
This SAE Recommended Practice establishes dimensions for wheels for demountable rims, demountable rims, and rim spacers. The dimensions given are those necessary to maintain serviceability and interchangeability of the demountable rims, rim spacers, and wheels for demountable rims. Special and less common applications are not covered in this recommended practice.
HISTORICAL
2007-09-07
Standard
J851_200709
This SAE Recommended Practice establishes dimensions for wheels for demountable rims, demountable rims, and rim spacers. The dimensions given are those necessary to maintain serviceability and interchangeability of the demountable rims, rim spacers, and wheels for demountable rims. Special and less common applications are not covered in this recommended practice.
CURRENT
2011-03-30
Standard
J851_201103
This SAE Recommended Practice establishes dimensions for wheels for demountable rims, demountable rims, and rim spacers. The dimensions given are those necessary to maintain serviceability and interchangeability of the demountable rims, rim spacers, and wheels for demountable rims. Special and less common applications are not covered in this recommended practice.
HISTORICAL
1963-11-01
Standard
J876_196311
This SAE Recommended Practice establishes uniform engineering nomenclature for wide base disc wheels and demountable rims. This nomenclature and accompanying figures are intended to define fundamental wide base disc wheels and demountable rim terms. The dimensions given are those necessary to maintain serviceability and interchangeability of the wide base disc wheels and demountable rims with standard hardware. Valve clearances have not been included in this document.
Viewing 1 to 30 of 58