Search Results

Selective Catalytic Reduction (SCR) catalysts have been demonstrated as an effective solution for controlling NOx emissions from diesel engines. Typical 2010 Heavy-Duty systems include a DOC along with a catalyzed soot filter (CSF) in addition to the SCR sub-assembly. There is a strong desire to further increase the NOx conversion capability of such systems, to enable additional fuel economy savings by allowing engines to be calibrated to higher engine-out NOx levels. One potential approach is to replace the CSF with a diesel particulate filter coated with SCR catalysts (SCR-DPF) while keeping the flow-through SCR elements downstream, which essentially increases the SCR volume in the after-treatment assembly without affecting the overall packaging. In this work, a system consisting of SCR-DPF was evaluated in comparison to the DOC + CSF components from a commercial 2010 DOC + CSF + SCR system on an engine with the engine EGR on (standard engine-out NOx) and off (high engine-out NOx).

Post-injection strategies aimed at reducing engine-out emissions of unburned hydrocarbons (UHC) were investigated in an optical heavy-duty diesel engine operating at a low-load, low-temperature combustion (LTC) condition with high dilution (12.7% intake oxygen) where UHC emissions are problematic. Exhaust gas measurements showed that a carefully selected post injection reduced engine-out load-specific UHC emissions by 20% compared to operation with a single injection in the same load range. High-speed in-cylinder chemiluminescence imaging revealed that without a post injection, most of the chemiluminescence emission occurs close to the bowl wall, with no significant chemiluminescence signal within 27 mm of the injector. Previous studies have shown that over-leaning in this near-injector region after the end of injection causes the local equivalence ratio to fall below the ignitability limit.

The engineering process in the development of commercial vehicles is facing more and more stringent emission regulations while at the same time the market demands for better performance but with lower fuel consumption. The optimization of aerodynamic performance for reduced drag is a key element for achieving related performance targets. Closely related to aerodynamics are wind noise and cabin soiling and both of them are becoming more and more important as a quality criterion in many markets. This paper describes the aerodynamic and aero-acoustic performance evaluation of a Dongfeng heavy truck using digital simulation based on a LBM approach. It includes a study for improving drag within the design of a facelift of the truck. A soiling analysis is performed for each aerodynamic result by calculating the accumulation of particles emitted form the wheels on the cabin. One of the challenges in the development process of trucks is that different cabin types have to be designed.

Models for off-road vehicles, such as farm equipment and military vehicles, require an off-road tire model in order to properly understand their dynamic behavior on off-road driving surfaces. Extensive literature can be found for on-road tire modeling, but not much can be found for off-road tire modeling. This paper presents an off-road tire model that was developed for use in vehicle handling studies. An on-road, dry asphalt tire model was first developed by performing rolling road force and moment testing. Off-road testing was then performed on dirt and gravel driving surfaces to develop scaling factors that explain how the lateral force behavior of the tire will scale from an on-road to an off-road situation. The tire models were used in vehicle simulation software to simulate vehicle behavior on various driving surfaces. The simulated vehicle response was compared to actual maximum speed before sliding vs. turning radius data for the studied vehicle to assess the tire model.

Vehicles on the road operate in the turbulent flow field resulting from the combined effects of the natural wind and the wakes of other vehicles. While substantial data exists on the properties of the natural wind, much less information is available for the wake properties of road vehicles. The wake information available for road vehicle shapes is mainly restricted to the near wake region, but to understand the vehicle operating environment it is the wake downstream of this region which is of interest. To determine the range of this area of interest requires some knowledge of the decay of the wake properties. From wind tunnel studies using small simple bluff bodies in free stream and in ground proximity the principle wake properties, velocity deficit and peak turbulence intensity have been measured. The maximum velocity deficit is shown to approximately decay with x-2/3, where x is the distance downstream, while turbulence intensity decays at a slightly slower rate.

A numerical simulation model for predicting the fuel hydrocarbon permeation as well as the barrier layer thickness optimization for multilayer plastic fuel tanks is presented. The diffusion model is based on Fick's laws of diffusion for a steady/unsteady state permeation regime through a multilayer polymeric wall under isothermal condition. A continuum approach based on an homogenization technique is used to model solvent diffusion through an n layer film. The hydrocarbon flux determination through the multilayer film is solved using homogenization techniques that ensure continuity of partial pressure at the polymer-polymer inter-diffusion interface. Since the pinch-off zone is known to be the major source of emission per unit area, a method has been developed to automatically detect it at the end of the extrusion blow molding process and the diffusion model is adapted to adequately evaluate the hydrocarbon permeation through this specific area.

The drive to incorporate renewable resources continues to gain momentum within the automotive industry. FXI has developed a grade of low (1.7 pcf) density slabstock foam which uses a natural oil polyol in place of a petroleum-based polyol. This foam grade, trademarked GreenBlend\St, has been developed specifically to produce foam-fabric/vinyl laminates for automotive seating, and interior trim applications such as headrests, armrests, visors and door panels. This new foam grade satisfies all of the OEM specifications for physical properties, including fogging and flammability, and yields satisfactory bond strengths when flame-laminated to cover stock. It is also s cost competitive technology compared to conventional slabstock foam using petroleum-based polyols.

Due to the importance of the fast transportation under every circumstance, the transportation process may require a high speed heavy vehicle from time to time, which may turn the transportation process more unsafe. Due to that fact the truck safety during braking and the ride comfort during long distance travelling with high speeds should be improved. Therefore, the aim of this work is to develop a control system which combines the suspension and braking systems. The control system consists of three controllers; the first one for the active suspension system of the truck body and cab, the second one for the ABS and, the third for the integrated control system between the active suspension system and the ABS. The control strategy is also separated into two strategies.

This paper describes the development of the fixed seat eyellipse in the October 2008 revision of SAE Recommended Practice J941. The eye locations of 23 men and women with a wide range of stature were recorded as they sat in each of three second-row bench seats in a laboratory mockup. Testing was conducted at 19-, 23-, and 27-degree seat back angles. Regression analysis demonstrated that passenger eye location was significantly affected by stature and by seat back angle. The regression results were used to develop an elliptical approximation of the distribution of adult passenger eye locations, applying a methodology previously used to develop the driver eyellipse in SAE J941-2002.

In order to build a useful and comfortable in-car human machine interface systems, the information presentation method should be easy to understand (low mental workload) and one should be able to respond with ease to the information presented (low response workload). We are making efforts to establish an evaluation method that would differentiate between mental workload and response workload. Here, we present the results of our trial using brain waves measurements (Eye Fixation Related Potentials). We focus on the relation between P3 latencies and drivers response workload compared to mental workload in a task involving eye movements. Previous experiments showed that P3 latency correlates strongly with the amount of information presented. The current experiment shows that P3 latencies seem to be independent to the type of response the subject is requested to perform.

This paper presents a verification of the effectiveness of an image processing method, used to reduce the inconsistent speed perception caused by using the camera images in conjunction with side-view mirrors. Vision assistance technology using cameras is widely used in practical applications today. However, speed and distance perceived with camera images may differ from those viewed directly or viewed with conventional side-view mirrors. That is particularly evident in wide-angle camera images, and can easily cause a sense of discomfort experienced by the driver. A Side View Camera (SVC) shows images rearward and to the side that include the blind spots of side-view mirrors on an onboard display. It is a system to compensate side-view mirrors, broadening the driver's field of view to eliminate bind spots. SVC is used in conjunction with the side-view mirrors.

This paper presents a purge system model developed for hybrid electric vehicle (HEV) applications. Assessment of purge capability is critical to HEV vehicles due to frequent engine off operation which limits carbon canister purging. The purge model is comprised of subsystems representing purge control strategy, carbon canister and engine plant. The paper is focused on modeling of the engine purge control feature. The purge model validation and purge capability predictions for an example HEV vehicle are presented and discussed.

This paper presents a simulation based analysis of the effect of various non-linearities on vehicle handling of rigid and articulated vehicles. First a description of a non-linear vehicle model is presented and non-linearities, including tires, suspension elasto-kinematics, springing and damping are discussed. Later sections present the simulations results for the effects of each non-linearity. Simulation analyses are carried out for the case of step steering maneuvers, which permit to deduce the overall vehicle model response variation in steady-state and dynamic conditions.

The aim of the study was to investigate the cooling performance of two cooling package positions for distribution vehicles by using Computational Fluid Dynamics. The first cooling package was positioned in the front of the vehicle, behind the grill and the second position was at the rear of the vehicle. Each case was evaluated by its cooling performance for a critical driving situation and its aerodynamic drag at 90 km/h, where the largest challenge of an alternative position is the cooling air availability. The geometry used was a semi-generic commercial vehicle, based on a medium size distribution truck with a heat rejection value set to a fixed typical level at maximum power for a 13 litre Euro 6 diesel engine. The heat exchangers included in the study were the air conditioning condenser, the charge air cooler and the radiator. It was found that the main problem with the rear mounted cooling installation was the combination of the fan and the geometry after the fan.

The aim with this investigation was to study the aerodynamic properties of truck-trailer combinations of varying lengths. The aerodynamic properties of the combinations were evaluated in order to study similarities and differences in the flow field between different configurations. By the use of Computational Fluid Dynamics (CFD) six different types of truck-trailer combinations used for long hauling have been evaluated. The combinations have a total length varying between 10.10 m and 25.25 m and consist of either a tractor or rigid truck in combination with one or two cargo units. All of the combinations are commonly found on roads in Sweden and several other countries in Europe. The results from the simulations show that the aerodynamic properties differ significantly for the truck-trailer combinations. It was found that the longer vehicle combinations are much more sensitive to yaw conditions than the shorter combinations.

The paper investigates the interaction between soil and tractor tires through a 2D numerical model. The tire is schematized as a rigid ring presenting a series of rigid tread bars on the external circumference. The outer profile of the tire is divided into a series of elements, each one able to exchange a normal and a tangential contact force with the ground. A 2D soil model was developed to compute the forces at the ground-tire interface: the normal force is determined on the basis of the compression of the soil generated by the sinking of the tire. The soil is modeled through a layer of springs characterized by two different stiffness for the loading (lower stiffness) and unloading (higher stiffness) condition. This scheme allows to introduce a memory effect on the soil which results stiffer and keeps a residual sinking after the passage of the tire. The normal contact force determines the maximum value of tangential force provided before the soil fails.

With growing globalization of the economy, to gain a competitive edge in world markets shortening the product development cycle is crucial. Virtual product development is, therefore, being actively pursued in the off-road vehicle industry. To implement this process successfully, the development of comprehensive and realistic computer-aided methods for performance and design evaluation of off-road vehicles is of vital importance. To be useful to the engineer in industry for the development and design of new products, the computer-aided methods should take into account all major vehicle design parameters and pertinent terrain characteristics. They should be based on the understanding of the physical nature and the mechanics of vehicle-terrain interaction. Their capabilities should be substantiated by test data.

Battlefield reconnaissance is an integral part of today's integrated battlefield management system. Current reconnaissance technology typically requires land based vehicle systems to observe while stationary or, at best, significantly limits travel speeds while collecting data. By combining current Canadian Light Armored Vehicle based reconnaissance systems with the Center for Electromechanics (CEM) electronically controlled active Electromechanical Suspension System (EMS), opportunities exist to substantially increase cross-country speeds at which useful reconnaissance data may be collected. This report documents a study performed by The University of Texas Center for Electromechanics with funding from L3-ES to use existing modeling and simulation tools to explore potential benefits provided by EMS for reconnaissance on the move.

The planar rigid bicycle model is one of the most popular models used in vehicle dynamics. It has widely been used in studying vehicle handling characteristics and designing steering control system for vehicles. This paper analyses a modified dynamic model called the "Elastic Bicycle Model." This model improves upon the classical bicycle model by taking into account the flexibility of the vehicle frame by using concepts from the Euler beam theory. Complete set of the resulting dynamic equations of this model are presented. Non-dimensional versions of the equations are used to investigate the steady state response of the model. Finally, the results of the response study obtained by modeling a small truck with an elastic model and the classical bicycle model are presented. These include the steady state solutions as function of different parameters as well as a transient solution in response to a saw-tooth steering input and a step input. Octave® has been used for simulation purpose.

To reduce NOx emissions from a heavy-duty engine at low exhaust temperature conditions, the plasma-assisted SCR (Selective Catalytic Reduction) system was evaluated. The plasma-assisted SCR system is mainly composed of an ammonia gas supply system and a plasma reactor including a pellet type SCR catalyst. The preliminary test with simulated gases of diesel exhaust showed an improvement in the NOx reduction performance by means of the plasma-assisted SCR system, even below 150°C conditions. Furthermore, NOx reduction ratio was improved up to 77% at 110°C with increase in the catalyst volume. Also NOx emissions from a heavy-duty diesel engine over the transient test mode in Japan (JE05) were reduced by the plasma-assisted SCR system. However, unregulated emissions, e.g., aldehydes, were increased with the plasma environment. This paper reports the advantages and disadvantages of the plasma-assisted SCR system for a heavy-duty diesel engine.