Search Results

The undesired Drag Torque (DT) which is developed due to the shearing of fluid film in between the disk and separator plate reduces the efficiency of a transmission and increases the fuel consumption of a car. In order to minimize the transmission loss, the physics of the fluid flow mechanism inside the clutch should be understood well and the factors influencing the DT should be identified. In this paper, a model is proposed to predict the drag torque of a disengaged wet clutch at different rotation speeds, clearances, disk sizes and oil temperatures. The model explains well how the DT changes for the no groove disk, grooved disk and different ATF properties. The proposed model is validated by several experimental results conducted by a visualization tester and images of the fluid film taken during the test. Results show that there is a good degree of agreement between the DT trends derived from the proposed model and the test results for the same condition.

Shift quality of a manual transmission is a critical characteristic that requires utmost care while structuring the transmission. Shift quality is affected by many factors viz. synchronizer design, shifter design, gear design, transmission oil selection etc. This paper presents a correlation between stiffness of the shift fork in manual transmission with the gear shift quality using a gear shift quality assessment setup. Stiffness of shifter fork is optimized using contact pattern analysis and stiffness analysis on MSC Nastran. All the subsystem (i.e. synchronizer and the shift system component) are constrained to optimize the shift fork stiffness. A-5-speed manual transmission is used as an example to illustrate the same. A direct correlation of gear shift fork stiffness with the shift force experienced by the driver is established. The shift system was modeled in the UG NX 6.0 software to collate the synchronization force, shift system gap etc with the constraint on the shift fork.

The automotive world has seen an increase in customer demands for vehicles having low noise and vibrations. One of the most important source of noise and vibrations associated with vehicles is the vibration of driveline systems. For commercial vehicles, the refinement of drivelines from NVH point of view is complex due to the cost and efficiency constraints. The typical rear wheel drive configuration of commercial vehicles mostly amplifies the torsional vibrations produced by engine which results into higher noise in the vehicle operating speed range. Theoretically, there are various options available for fine tuning the torsional vibration performance of the vehicle drive train. The mass moments of inertia and stiffness of the drivetrain components play significant role in torsional vibration damping, however, except minor changes to flywheel mass, it is hardly possible to change other components, subject to design limitations.

This paper focuses on modeling of the heavy-duty vehicle drivetrain with automatic transmission by using dual clutch scheme. The planetary gear set in the automatic transmission is complicated structure and difficult to understand. The advantage of the dual clutch scheme is that it can be used to represent the complex planetary gear set intuitively, which is a great help to understand the gear shifting process. It is also suitable for being used in the controller due to its low order. Some conditions are required to convert the planetary gear set to the dual clutch model. The heavy-duty vehicle driveline can be converted to the dual clutch model due to its heavy engine and vehicle inertia. This paper also proposes system parameter estimation methods to represent the driveline model. The main parameters are lumped inertia, lumped gear efficiency, output shaft compliance and friction coefficient of clutches.

In today’s automobile industry refined NVH performance is a key feature and of high importance governing occupant comfort and overall quality impression of vehicle. In this paper interior noise and vibration measurement is done on one of the light truck and few dominant low frequency noise booms were observed in operation range. Modal analysis was done for the cabin at virtual as well as experimental level and few modes were found close to these noise booms. Vibrations were measured across the cabin mounts and it was found that the isolation of front mounts is not effective at lower frequencies. Taking this as an input, the mount design was modified to shift the natural frequency and hence improve the isolation behavior at the lowest dominant frequency. This was followed by static and dynamic measurement of the mounts at test rig level to characterize the dynamic performance and stiffness conclusion.

Downsizing and Light weighting is the latest trend in the automotive industry to achieve more fuel efficient, compact and cost effective design of vehicles. Powertrain components compromise of more than 45% of the total vehicle weight. Automakers are putting significant efforts to reduce the weight of power train components. Integrated design of aluminum Engine Head and Intake manifold has been successfully implemented. Now currently we have identified the gear box housings for downsizing in light duty trucks i.e. Existing light duty trucks Cast Iron transmission. This design has been successfully modified with integrated clutch housing and transmission housing, using lightweight aluminum as the new material, using simulation tools. This lead to weight savings of up to 30% and cost savings of 20-25% as compared to existing cast iron designs. Using an integrated design reduces the assembly cost, makes the design more compact and gives better weight balance.

Autonomous vehicle operation is dependent upon accurate position estimation and thus a major concern of implementing the autonomous navigation is obtaining robust and accurate data from sensors. This is especially true, in case of Inertial Measurement Unit (IMU) sensor data. The IMU consists of a 3-axis gyro, 3-axis accelerometer, and 3-axis magnetometer. The IMU provides vehicle orientation in 3D space in terms of yaw, roll and pitch. Out of which, yaw is a major parameter to control the ground vehicle’s lateral position during navigation. The accelerometer is responsible for attitude (roll-pitch) estimates and magnetometer is responsible for yaw estimates. However, the magnetometer is prone to environmental magnetic disturbances which induce errors in the measurement.

This SAE Recommended Practice establishes uniform test procedures and performance requirements for engine-off heating, ventilation, and air conditioning (HVAC) systems in order to achieve driver thermal comfort in both winter and summer rest periods. This specification will apply to heavy trucks with and without sleeper compartments, including but is not limited to Class 6, 7, and 8 powered vehicles.

This SAE Recommended Practice establishes uniform test procedures and performance requirements for engine-off heating, ventilation, and air conditioning (HVAC) systems in order to achieve driver thermal comfort in both winter and summer rest periods. This specification will apply to heavy trucks with and without sleeper compartments, including but is not limited to Class 6, 7, and 8 powered vehicles.

This SAE Recommended Practice establishes a uniform test procedure for determining performance levels of operator enclosure panel type air filters on off-road, self-propelled work machines used in construction, general-purpose industrial, agriculture, and forestry as defined in SAE J1116 and equipped with an operator enclosure with a powered fresh air system.

This SAE Standard describes methods for evaluating the performance of the systems detection device, the minimum detection areas behind the machine, the visual and audible information presented to the operator and ground personnel, and the systems fault detection requirements. Also included are operator system function tests and maintenance procedures.

Although not limited to, these installations are normally used on trucks considered as Medium Duty (Class 6 and 7), as well as Heavy Duty (Class 8).

Although not limited to, these installations are normally used on trucks considered as Medium Duty (Class 6 and 7), as well as Heavy Duty (Class 8).

Although not limited to, these clutches are normally used on trucks considered as Medium-Duty (Class 6 and 7), as well as Heavy-Duty (Class 8).

Although not limited to, these clutches are normally used on trucks considered as Medium-Duty (Class 6 and 7), as well as Heavy-Duty (Class 8).

Although not limited to, these installations are normally used on trucks considered as Medium Duty (Class 6 and 7), as well as Heavy Duty (Class 8).

This SAE Information Report provides basic information about the issues surrounding the administration of stationary, infield sound testing of snowmobiles. The information provided herein is meant to enhance safety, improve the environment and promote uniform testing.

This SAE Information Report provides basic information about the issues surrounding the administration of stationary, infield sound testing of snowmobiles. The information provided herein is meant to enhance safety, improve the environment and promote uniform testing.

This SAE Information Report provides basic information about the issues surrounding the administration of stationary, infield sound testing of snowmobiles. The information provided herein is meant to enhance safety, improve the environment, and promote uniform testing.

This SAE Recommended Practice applies to all forms of diesel and natural gas engines fueled by the combination of diesel fuel and natural gas.