Search Results

This SAE Recommended Practice provides a systematic method for the identification of End Mills. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designation to prevent specifying cutting tools that cannot be physically or economically manufactured. NOTE 2— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.

This SAE Recommended Practice provides a systematic method for the identification of End Mills. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designation to prevent specifying cutting tools that cannot be physically or economically manufactured. NOTE 2— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.

The scope of this SAE Recommended Practice is restricted to the testing of original equipment on passenger vehicles and to provide for a uniform industry test procedure.

The scope of this SAE Recommended Practice is restricted to the testing of original equipment on passenger vehicles and to provide for a uniform industry test procedure.

This SAE Recommended Practice is intended to provide guidelines for the identification of subjects used in dynamic tests. It establishes recommendations for location and description of target areas on test subjects or test devices, as well as recommendations for photographic calibration and timing.

This SAE Recommended Practice is intended to provide guidelines for the identification of subjects used in dynamic tests. It establishes recommendations for location and description of target areas on test subjects or test devices, as well as recommendations for photographic calibration and timing.

Almost all light trucks now are being manufactured with at least a driver side air bag and all will have dual air bags by 1998. The driving forces behind this feature are occupant safety, federal regulations, and competition in the industry. Along with the booming popularity of pickups and SUVs, they are commonly accessorized with a wide variety of products. Many accessories for four-wheel drives in particular are mounted on the front of the vehicle. These products include grille/brush guards, winches, snow plows, replacement bumpers, bicycle carriers, etc. Concerns have arisen over the compatibility of these accessories with the vehicle’s air bag system. The vehicle manufacturers are concerned because of their huge investment in design and crash test verification of the complete vehicle system and keen awareness of the federal regulations. The crushability of the front bumper and supporting structure are key elements in the system, so alterations to that area become logical concerns.

Almost all light trucks now are being manufactured with at least a driver side air bag and all will have dual air bags by 1998. The driving forces behind this feature are occupant safety, federal regulations, and competition in the industry. Along with the booming popularity of pickups and SUVs, they are commonly accessorized with a wide variety of products. Many accessories for four-wheel drives in particular are mounted on the front of the vehicle. These products include grille/brush guards, winches, snow plows, replacement bumpers, bicycle carriers, etc. Concerns have arisen over the compatibility of these accessories with the vehicle’s air bag system. The vehicle manufacturers are concerned because of their huge investment in design and crash test verification of the complete vehicle system and keen awareness of the federal regulations. The crushability of the front bumper and supporting structure are key elements in the system, so alterations to that area become logical concerns.

The scope of this document is limited specifically to the following types of passenger vehicles: automobiles, light trucks, and sport/utility vehicles. This document addresses modifications as they apply to legal use of the vehicle, and examines suspension modification as it applies to stock (as manufactured) ride height, and changed (raised or lowered) ride height. Note that modifications of ride height are considered, exclusive of wheel and/or tire modifications, which can also have potentially serious side effects, and are outside the scope of this document.

This SAE Recommended Practice describes the type of equipment commonly used with towing equipment, provides information to calculate safe steering loads, and outlines design criteria.

This SAE Recommended Practice describes the type of equipment commonly used with towing equipment, provides information to calculate safe steering loads, and outlines design criteria.

This SAE Recommended Practice establishes uniform test procedures for evaluating vehicle hood latch systems. It specifically pertains to those latch systems on hoods, which when the hood is fully opened (assuming the absence of hood stops) extend at any point above a horizontal plane through the uppermost edge of the steering wheel in the straight ahead driving position with the vehicle in a horizontal position. The following optional tests are described. a Vehicle Performance Tests—On-the-road evaluation under an established pattern of vehicle driving situations. b Laboratory Dynamic Tests—Dynamic simulation in the laboratory of the loads and forces which the latch system encounters on the road. c Laboratory Static Tests—Simplified test procedures intended to permit static simulation of the loads which road tests have indicated the latch system may encounter. The test procedures outlined in this recommended practice are based on current engineering test methods.

This SAE Recommended Practice establishes uniform test procedures for evaluating vehicle hood latch systems. It specifically pertains to those latch systems on hoods, which when the hood is fully opened (assuming the absence of hood stops) extend at any point above a horizontal plane through the uppermost edge of the steering wheel in the straight ahead driving position with the vehicle in a horizontal position. The following optional tests are described. (a) Vehicle Performance Tests—On-the-road evaluation under an established pattern of vehicle driving situations. (b) Laboratory Dynamic Tests—Dynamic simulation in the laboratory of the loads and forces which the latch system encounters on the road. (c) Laboratory Static Tests—Simplified test procedures intended to permit static simulation of the loads which road tests have indicated the latch system may encounter. The test procedures outlined in this recommended practice are based on current engineering test methods.

This SAE Recommended Practice describes performance requirements for hardware used in motor vehicle seat belt assemblies when tested in accordance with the test procedures specified in SAE J140. Test procedures and performance requirements for retractors will be covered in separate SAE Recommended Practices to be issued later.

This SAE Recommended Practice provides a systematic method for the identification of various types of hand, machine, and shell reamers used in industrial applications. When used as recommended in this report, the numbering system will assist in obtaining consistent reamer descriptions in communications. The report was developed in cooperation with the Automotive Industry Action Group (AIAG).

This SAE Recommended Practice provides a systematic method for the identification of single diameter and taper reamers. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designators to prevent specifying reamers that cannot be physically or economically manufactured. NOTE 2— The Code Number coming from the manufacturer MUST reflect the actual tool construction. NOTE 3— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.

This SAE Recommended Practice provides a systematic method for the identification of single diameter and taper reamers. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designators to prevent specifying reamers that cannot be physically or economically manufactured. NOTE 2— The Code Number coming from the manufacturer MUST reflect the actual tool construction. NOTE 3— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.

This SAE Recommended Practice provides a systematic method for the identification of single diameter drills. It is intended to assist in the cataloging and supplying of these tools.

This SAE recommended practice provides a systematic method for the identification of standard drills. It is intended to assist in the cataloging and supplying of these tools. The report was developed in cooperation with the Automotive Industry Action Group (AIAG).

This SAE Recommended Practice provides a systematic method for the identification of single diameter drills. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designators to prevent specifying drills that cannot be physically or economically manufactured. NOTE 2— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.