Refine Your Search

Date

Date

Topic

Topic

Tools and equipment Casting Technical review Manufacturing G-33 Configuration Management

Search Results

Viewing 1 to 20 of 28
12Next >Last >>
Sort by relevance
Standard

Manufacturing Message Specification – Service Definition and Protocol
2016-06-28
CURRENT
EIA511
The Manufacturing Message Specification is an application layer Standard designed to support messaging communications to and from programmable devices in a Computer Integrated Manufacturing (CIM) environment. This environment is referred to in this Standard as the manufacturing environment. This Standard does not specify a complete set of services for remote programming of devices, although provision of such a set of services may be the subject of future standardization efforts.
Standard

Interface between Numerical Control Equipment and Data Terminal Equipment Employing Parallel Binary Data Interchange
2016-06-16
CURRENT
EIA408
This standard applies to the interconnection of data terminal equipment and numerical control equipment at the tape reader interface. The data terminal would typically be connected to a remote data source/sink such as a computer. This standard defines: This standard is applicable for the interchange of signals when used in conjunction with electronic equipment, each interchange circuit of which has a single return (signal ground) that can be interconnected at the interface point. Figure 1.1, typical installation, shows how this standard should be applied to a typical tape reader interface of numerical control equipment.
Standard

Glossary of Terms, Acronyms, and Definitions
2014-10-01
CURRENT
CMB7_4A
This Bulletin provides a comprehensive list of Terms and Definitions used in or related to TechAmerica prepared standards/documents. The information in these listings was extracted from standards and documents prepared by the Systems Engineering (G47), Configuration Management (G33), Life Cycle Logistics Supportability and Enterprise Information Management Interoperability Committees along with other pertinent international, industry and government standards. It is intended that this bulletin be used as a resource to help with harmonization of terms and definitions across standards. One should be cognizant of the release date of this Bulletin and understand that updates to the included standards and handbooks after this Bulletin was released may affect its accuracy.
Standard

Configuration Management Requirements for Subcontractors/Vendors
2014-10-01
CURRENT
CMB5A
The role of CM, within any one company's organization, on the development and production of a product has been established by internal company needs or imposed by customer dictum. (As used hereinafter, in order to reduce any confusion, computer programs, components, software, hardware, firmware, etc., are included in the designation "PRODUCT".) The primary focus of this Bulletin is directed toward the Buyer and Supplier personnel who will be managing hardware products in the production phase and software products in the full-scale development phase. The trend in DoD is toward expanded use of standardized components and subassemblies, using competitive reprocurement. The DoD needs to know the full span of CM requirements which should be included in the production contract and the management tasks that will have to be accomplished.
Standard

Configuration Management Definitions for Digital Computer Programs
2014-10-01
CURRENT
CMB4_1A
This Bulletin is intended for use as a guide and defines the terms and definitions to be used during the development, documentation, verification, and delivery cycles of new and modified computer software. It lists and defines the most common terms currently used in the world of computer software configuration management. There has been no attempt to compete with some of the more formal documents in use within the software programming community.
Standard

Character Code for Numerical Machine Control Perforated Tape
2015-07-01
CURRENT
EIA244
This standard for Numerical Machine Control Perforated Tape is intended to serve as a guide in the coordination of equipment design, to minimize the number of sizes and codes of perforated tape used, and to minimize the variety of perforated tape preparation equipment required by users of numerically controlled machines.
Standard

Requirements for the Control of Electromagnetic Interference Emissions and Susceptibility Characteristics of Equipment Intended to Operate in Severe Electromagnetic Environments
2016-06-16
CURRENT
EIAIS647
This standard establishes the performance requirements for the control of the electromagnetic emission and susceptibility characteristics of electronic, electrical, and electromechanical equipment and subsystems designed or procured for use in severe electromagnetic environments such as ships, aircraft, spacecraft, armored vehicles, etc. Such equipment and subsystems may be used independently or as an integral part of other subsystems or systems.
Standard

Configuration Control
2014-10-01
CURRENT
CMB6_4
This Interface Control Plan establishes a program for interface control among the major segments/equipments of a DoD program. This could be an airborne weapon system, Medium Launch Vehicle System, Space Launch Complex System, etc. The program is based on formal agreements between participating organizations, and includes (1) documentation to establish, define and control interface requirements and to detail interface design definition between system segments, (2) interface management under the purview of the Interface Management Boards (IMB) and (3) interface control, through Interface Control Working Groups (ICWGs). The plan establishes the IMB and ICWG policy and procedures. Furthermore, it sets forth the Government Agencies Program Offices, associate contractors and participating Government Agency responsibilities in support of the Interface Control Program and the conduct of interface management/control through the IMBs, and ICWGs.
12Next >Last >>
X