Search Results

Electric vehicles with multiple motors permit continuous direct yaw moment control, also called torque-vectoring. This allows to significantly enhance the cornering response, e.g., by extending the linear region of the vehicle understeer characteristic, and by increasing the maximum achievable lateral acceleration. These benefits are well documented for human-driven cars, yet limited information is available for autonomous/driverless vehicles. In particular, over the last few years, steering controllers for automated driving at the cornering limit have considerably advanced, but it is unclear how these controllers should be integrated alongside a torque-vectoring system. This contribution discusses the integration of torque-vectoring control and automated driving, including the design and implementation of the torque-vectoring controller of an autonomous electric vehicle for a novel racing competition. The paper presents the main vehicle characteristics and control architecture.

The paper deals with a method implemented to study braking systems design, modelling components' characteristics through commercial software. It summarizes the potential improvement possible by using modelling techniques in chassis systems design. The first part consisted in producing a passive braking system model. A first validation was carried out on a test bench by using components of different braking systems. Particular attention was devoted to booster modelization both in semi-stationary and dynamic conditions. The second part was callipers, roll-back and thermal phenomena modelization. Finally, it were modelled Anti-lock Braking System (ABS) and Vehicle Dynamics Control (VDC) Hydraulic Units and their integration with control strategies and with vehicle dynamics model.

The paper describes Politecnico di Torino braking systems test bench, based on hardware in the loop (HIL). The test bench, consisting of the whole braking system hardware, can be used for: Analysis of passive braking systems, to determine the main characteristics both in semi-stationary and dynamic conditions; Analysis of passive braking systems, to investigate the influence of eventual asymmetries on vehicle behaviour, since a vehicle model runs in real time and receives wheels pressure values by the sensors on the physical device; Analysis of Commercial Anti-lock Braking/Electronic Stability Program (ESP) Systems, both from the point of view of control strategies and hydraulic units performance; Definition of new ABS/ESP control strategies, e.g. considering wheels caliper pressure signals as inputs, using pre-existing commercial hydraulic units.

Over the last decade the simulation of driving cycles through longitudinal vehicle models has become an important stage in the design, analysis and selection of vehicle powertrains. This paper presents an overview of existing software packages, along with the development of a new multipurpose driving cycle simulator implemented in the Matlab/Simulink environment. In order to evaluate the performance of the simulator, a MAN TGL 12.240 multi-usage delivery vehicle was fitted with a CAN-bus data logger and used to create a series of ‘real-life’ drive cycles. These were inputted into the vehicle model and the simulated fuel mass flow-rate and engine rotational speed were compared to those experimentally obtained.

The paper presents the approach followed by Politecnico di Torino Vehicle Dynamics Research team to design an electro-mechanical Active Roll Control (ARC) system. The first part of the paper describes the targets of the system, which has to improve both comfort and handling. Different solutions for the implementation of the electro-mechanical actuation were evaluated. A prototype of the electro-mechanical Active Roll Control was built and experimentally tested in the Vehicle Dynamics Laboratory of the Department of Mechanics of Politecnico di Torino, by adopting a Hardware-In-the-Loop (HIL) test bench. The experimental results show the benefits of the system, both in a stand alone configuration and integrated with an Electronic Stability Control (ESC) system.

The paper shortly describes an ABS/ESP Hardware-In-the-Loop (HIL) test bench built by the Vehicle Dynamics Team of the Department of Mechanics of Politecnico di Torino. It consists of a whole brake system, integrated through specific interface (e.g. wheel pressures signals) with a vehicle model running in real time on a dSPACE® board. Different commercial ABS strategies are compared, in a large spectrum of manoeuvres: slow brake apply manoeuvres, panic brake manoeuvres, μ-split brake manoeuvres, brake manoeuvres with a sudden variation of the friction coefficient between tyres and ground. The paper deals with the generation of all the signals required for activating a commercial ESP: steering wheel angle, body yaw rate, body lateral acceleration, engine control, etc… Some of them are transmitted by CAN. Typical handling manoeuvres are used to test the ESP: step steer, double step steer, ramp steer, etc… Several brake manoeuvres are simulated while turning.

E-mobility is a game changer for the automotive domain. It promises significant reduction in terms of complexity and in terms of local emissions. With falling prices and recent technological advances, the second generation of electric vehicles (EVs) that is now in production makes electromobility an affordable and viable option for more and more transport mission (people, freight). Current e-vehicle platforms still present architectural similarities with respect to combustion engine vehicle (e.g., centralized motor). Target of the European project EVC1000 is to introduce corner solutions with in-wheel motors supported by electrified chassis components (brake-by-wire, active suspension) and advanced control strategies for full potential exploitation. Especially, it is expected that this solution will provide more architectural freedom toward “design-for-purpose” vehicles built for dedicated usage models, further providing higher performances.