Search Results

Standard

Thread Sealants

2001-08-06

HISTORICAL

J1615_200108

Male pipe threads, including male dryseal pipe threads, when made into assemblies or installed into ports, will generally leak if not covered with a sealant. This SAE Recommended Practice is intended as a guide to assist designers and/or users in the selection and application of various types of thread sealants. The designers and users must make a systematic review of each type and application and then select the sealant to fulfill the requirements of the application. The following are general guidelines and are not necessarily a complete list.

Standard

Thread Sealants

2016-08-16

HISTORICAL

J1615_201608

Male pipe threads, including male dryseal pipe threads, when made into assemblies or installed into ports, will generally leak if not covered with a sealant. This SAE Recommended Practice is intended as a guide to assist designers and/or users in the selection and application of various types of thread sealants. The designers and users must make a systematic review of each type and application and then select the sealant to fulfill the requirements of the application. The following are general guidelines and are not necessarily a complete list.

Standard

Thread Sealants

2021-01-27

CURRENT

J1615_202101

Male pipe threads, including male dryseal pipe threads, when made into assemblies or installed into ports, will generally leak if not covered with a sealant. This SAE Recommended Practice is intended as a guide to assist designers and/or users in the selection and application of various types of thread sealants. The designers and users must make a systematic review of each type and application and then select the sealant to fulfill the requirements of the application. The following are general guidelines and are not necessarily a complete list.

Standard

METALLIC AIR BRAKE SYSTEM TUBING AND PIPE

1976-07-01

HISTORICAL

J1149_197607

This SAE standard covers minimum requirements for two types of metallic tubing and pipe as used in automotive air brake systems. It includes material and performance specifications, corrosion precautions, and installation recommendations. Copper tubing is designated Type 1, and galvanized steel pipe Type 2.

Standard

METALLIC AIR BRAKE SYSTEM TUBING AND PIPE

1987-12-01

HISTORICAL

J1149_198712

This specification covers minimum requirements for two types of metallic tubing and pipe as used in automotive air brake systems. It includes material and performance specifications, corrosion precautions, and installation recommendations. Copper tubing is designated Type 1, and galvanized steel pipe Type 2.

Standard

Metallic Air Brake System Tubing and Pipe

2007-08-13

HISTORICAL

J1149_200708

This SAE Standard covers minimum requirements for two types of metallic tubing and pipe as used in automotive air brake systems. It includes material and performance specifications, corrosion precautions, and installation recommendations. Copper tubing is designated Type 1, and galvanized steel pipe Type 2.

Standard

METALLIC AIR BRAKE SYSTEM TUBING AND PIPE

1991-06-01

HISTORICAL

J1149_199106

This SAE Standard covers minimum requirements for two types of metallic tubing and pipe as used in automotive air brake systems. It includes material and performance specifications, corrosion precautions, and installation recommendations. Copper tubing is designated Type 1, and galvanized steel pipe Type 2.

Standard

Metallic Air Brake System Tubing and Pipe

2015-10-21

CURRENT

J1149_201510

This SAE Standard covers minimum requirements for two types of metallic tubing and pipe as used in automotive air brake systems. It includes material and performance specifications, corrosion precautions, and installation recommendations. Copper tubing is designated Type 1, and galvanized steel pipe Type 2.

Standard

Metric Nonmetallic Air Brake System Tubing1

2013-06-11

CURRENT

J1394_201306

This SAE Standard covers the minimum requirements for metric sizes of nonmetallic tubing as manufactured for use in air brake systems. Nonreinforced products are designated type A and reinforced products type B. It is not intended to cover tubing for any portion of the system that operates below -40 °C (-40 °F), above +93 °C (+200 °F), above a maximum working gage pressure of 1.0 MPa (150 psi), or in an area subject to attack by battery acid. This tubing is intended for use in the brake system for connections that maintain a basically fixed relationship between components during vehicle operation.

Standard

Dimensional Specifications for Non-Metallic Body Push-to-Connect Fittings Used On a Vehicular Air Brake System

2017-06-07

CURRENT

J2494/2_201706

This SAE Standard covers general dimensional specifications for non-metallic body reusable push to connect tube fittings for use in the piping of air brake systems on automotive vehicles. This type of fitting is intended for use with nylon tubing per SAE J844. It is not intended to restrict or preclude other designs of a tube fitting for use with SAE J844. Performance requirements for SAE J844 are covered in SAE J1131. See SAE J2494-3 for the performance requirements of Reusable (push-to-connect) fittings intended for use in Automotive Air Brake Systems and U.S. Department of Transportation FMVSS 571.106.

Standard

Dimensional Specifications for Non-Metallic Body Push-to-Connect Fittings Used On a Vehicular Air Brake System

2002-10-04

HISTORICAL

J2494/2_200210

This SAE Standard covers general dimensional specifications for non-metallic body reusable push to connect tube fittings for use in the piping of air brake systems on automotive vehicles. This type of fitting is intended for use with nylon tubing per SAE J844. It is not intended to restrict or preclude other designs of a tube fitting for use with SAE J844. Performance requirements for SAE J844 are covered in SAE J1131. See SAE J2494-3 for the performance requirements of Reusable (push-to-connect) fittings intended for use in Automotive Air Brake Systems and U.S. Department of Transportation FMVSS 571.106.

Standard

Dimensional Specifications for Metallic Body Push-to-Connect Fittings Used on a Vehicular Air Brake System

2017-05-30

CURRENT

J2494/1_201705

This SAE Standard covers general and dimensional specifications for brass bodied reusable Push to Connect tube fittings for use in the piping of vehicular air brake systems. This type of fitting is intended for use with nylon tubing per SAE J844. See SAE J2494-3 for the Performance Requirements of Reusable (Push to Connect) Fittings Intended for Use in Automotive Air Brake Systems and U.S. Department of Transportation, National Highway Traffic Safety Administration (NHTSA) Federal Motor Vehicle Safety Standards (FMVSS) 571.

Standard

Dimensional Specifications for Metallic Body Push-to-Connect Fittings Used on a Vehicular Air Brake System

2011-05-10

HISTORICAL

J2494/1_201105

This SAE Standard covers general and dimensional specifications for brass bodied reusable Push to Connect tube fittings for use in the piping of vehicular air brake systems. This type of fitting is intended for use with nylon tubing per SAE J844. See SAE J2494-3 for the Performance Requirements of Reusable (Push to Connect) Fittings Intended for Use in Automotive Air Brake Systems and U.S. Department of Transportation, National Highway Traffic Safety Administration (NHTSA) Federal Motor Vehicle Safety Standards (FMVSS) 571.

Standard

Cartridge Cavity

2023-06-02

CURRENT

J2494/4_202306

This SAE Standard covers complete general and dimensional data for the manufacture of, T6061-T6 Aluminum cavities designed to receive Push To Connect threadless fittings known as “cartridges“, for air brake applications. This document is not intended to specify or recommend any style or manufacture of such cartridges but to establish uniform cavity dimensions for interchangeability purposes.

Standard

Cartridge Cavity

2011-10-28

HISTORICAL

J2494/4_201110

This SAE Standard covers complete general and dimensional data for the manufacture of, T6061-T6 Aluminum cavities designed to receive Push To Connect threadless fittings known as “cartridges“, for air brake applications. This document is not intended to specify or recommend any style or manufacture of such cartridges but to establish uniform cavity dimensions for interchangeability purposes.

Standard

Cartridge Cavity

2018-10-30

HISTORICAL

J2494/4_201810

This SAE Standard covers complete general and dimensional data for the manufacture of, T6061-T6 Aluminum cavities designed to receive Push To Connect threadless fittings known as “cartridges“, for air brake applications. This document is not intended to specify or recommend any style or manufacture of such cartridges but to establish uniform cavity dimensions for interchangeability purposes.

Standard

AIR BRAKE TUBING AND PIPE

1963-06-01

HISTORICAL

J844_196306

The following specifications cover minimum requirements for tubing or pipe used in automotive air brake systems. It covers corrosion precautions, installation, and material specifications.

Standard

Nonmetallic Air Brake System Tubing

2012-12-19

CURRENT

J844_201212

Standard

Spherical and Flanged Sleeve (Compression) Tube Fittings

2022-01-12

CURRENT

J246_202201

This SAE Standard covers complete general and dimensional specifications for tube fittings of the spherical and flanged sleeve compression types for use in the piping of air brake systems on automotive vehicles. The spherical sleeve compression type Figures 1A to 5 and Tables 1 to 3 is intended for use with annealed copper alloy tubing per SAE J1149, Type 1. The flanged sleeve compression type Figures 6A to 11 and Tables 4 to 6 is intended for use with nylon tubing per SAE J844. It is not intended to restrict or preclude other designs of a tube fitting for use with SAE J844, air brake tubing. Performance requirements for SAE J844 are covered in SAE J1131. See SAE J1131 for the Performance Requirements of Reusable (Push to Connect) Fittings Intended for Use in Automotive Air Brake Systems.

Standard

Spherical and Flanged Sleeve (Compression) Tube Fittings

2017-11-29

HISTORICAL

J246_201711

This SAE Standard covers complete general and dimensional specifications for tube fittings of the spherical and flanged sleeve compression types for use in the piping of air brake systems on automotive vehicles. The spherical sleeve compression type Figures 1A to 5 and Tables 1 to 3 is intended for use with annealed copper alloy tubing per SAE J1149, Type 1. The flanged sleeve compression type Figures 6A to 11 and Tables 4 to 6 is intended for use with nylon tubing per SAE J844. It is not intended to restrict or preclude other designs of a tube fitting for use with SAE J844, air brake tubing. Performance requirements for SAE J844 are covered in SAE J1131. See SAE J1131 for the Performance Requirements of Reusable (Push to Connect) Fittings Intended for Use in Automotive Air Brake Systems.