Search Results

A realistic modeling of the wall heat transfer is essential for an accurate analysis and simulation of the working cycle of internal combustion engines. Empirical heat transfer formulations still dominate the application in engine process simulations because of their simplicity. However, experiments have shown that existing correlations do not provide satisfactory results for all the possible operation modes of hydrogen internal combustion engines. This paper describes the application of a flow field-based heat transfer model according to Schubert et al. [1]. The models strength is a more realistic description of the required characteristic velocity; considering the influence of the injection on the global turbulence and on the in-cylinder flow field results in a better prediction of the wall heat transfer during the compression stroke and for operations with multiple injections. Further an empirical hypothesis on the turbulence generation during combustion is presented.

Turbulence anisotropy has a great influence on mixture formation and flame propagation in internal combustion engines. However, the visualization of turbulence in simulations is not straightforward; traditional methods lack the ability to display the anisotropic properties in the engine geometry. Instead, they use invariant maps, and important information about the locality of the turbulence anisotropy is lost. This paper overcomes this shortcoming by visualizing the anisotropy directly in the physical domain. Componentality contours are applied to directly visualize the anisotropic properties of turbulence in the three-dimensional engine geometry. Using an RGB (red, green, blue) color map, the three limiting states of turbulence (one-component, axisymmetric two-component and isotropic turbulence) are displayed in the three-dimensional physical domain.

Lean burn combustion concepts with high mean effective pressures are being pursued for large gas engines in order to meet future stringent emission limits while maintaining high engine efficiencies. Since severe boundary conditions for the ignition process are encountered with these combustion concepts, the processes of spark ignition and flame initiation are important topics of applied research, which aims to avoid misfiring and to keep cycle-to-cycle combustion variability within reasonable limits. This paper focuses on the fundamental investigation of early flame kernel development using different ignition system settings. The investigations are carried out on a rapid compression-expansion machine in which the spark ignition process can be observed under engine-like pressure and excess air ratio conditions while low flow velocities are maintained.

As emission limits become increasingly stringent and the price of gaseous fuels decreases, more emphasis is being placed on promoting gas engines. In the field of large engines for power generation, dual fuel combustion concepts that run on diesel/natural gas are particularly attractive. Knock in diesel/natural gas dual fuel engines is a well known yet not fully understood complex phenomenon that requires consideration in any attempt to increase load and efficiency. Thus combustion concept development requires a reliable yet robust methodology for detecting knock in order to ensure knock-free engine operation. Operating parameters such as rail pressure, start of injection and amount of diesel injected are the factors that influence oscillations in the in-cylinder pressure trace after the start of combustion. Oscillations in the pre-mixed combustion phase, or ringing, are caused by the rapid conversion of large parts of the injected diesel.

High-pressure direct injection (HPDI) of natural gas into the combustion chamber enables a non-premixed combustion regime known from diesel engines. Since knocking combustion cannot occur with this combustion process, an increase in the compression ratio and thus efficiency is possible. Due to the high injection pressures required, this concept is ideally suited to applications where liquefied natural gas (LNG) is available. In marine applications, the bunkering of and operation with LNG is state-of-the-art. Existing HPDI gas combustion concepts typically use a small amount of diesel fuel for ignition, which is injected late in the compression stroke. The diesel fuel ignites due to the high temperature of the cylinder charge. The subsequently injected gas ignites at the diesel flame. The HPDI gas combustion concept presented in this paper is of a monovalent type, meaning that no fuel other than natural gas is used.

When developing and later using simulation models for combustion prediction in internal combustion engines, it is first of all necessary to determine the model constants. This paper describes the development of a method for the automated determination of model parameters which can be applied to any internal combustion simulation model. The work is not aimed at developing a new optimizing algorithm but at adjusting and adapting an existing optimizer to the special needs and convergence problems, which occur when applied to combustion models. Consequently, the paper describes the set-up of the objective function and several methods for improving the convergence. Finally, an outline for a strategy which uses the optimizing tool for model development is presented.

This paper will present a system still in development that can be used both to generate electric energy and to start combustion engines. What's more, this system functions as multiband damper and takes over the complete flywheel function. Conventional technology as we know it today is briefly reviewed and subjected to a comparison with ISAD® technology. This paper contains system descriptions, readings and diagrams for various functions and a presentation of the whole system in a select trial vehicle. The results show that a system of this kind is not only capable of replacing current technology but can also cover all the (presently known) future requirements - noiseless start operation, low-vibration idle, acceleration boosting and an extremely powerful alternator (>6-10 kW at η > 80%), which allows, for example, for the electrification of all the vehicle's auxiliary aggregates. Significant fuel savings and emissions reductions are also achieved.

Highest grow or highest attention in vehicles power-train is related to AWD and hybrid concepts. Some of the targets for these technologies are conflicting, others are very similar, and sometimes it depends on the application. In a first look it is very questionable weather these technologies should be combined. But it can be shown, that the combination makes quite some sense. It is possible to get the superior performance and enhance safety combined with reasonable fuel economy by hybridizing an AWD powertrain. From simulation to testing, efficient processes and a consistent development platform is key to fulfill all the development tasks in the environment of this increased complexity. Simulation and benchmark activities are valuable in the early project phases to define the targets and create the specifications. In the virtual world the system selection is a major task. To get appropriate results software modules are incorporated in the simulation environment.

The incorporation of a detailed engine process calculation that takes into account thermal behavior of the engine and exhaust system is essential for a realistic simulation of transient vehicle operation. This is the only possible way to have a precise preliminary calculation of fuel consumption and emissions. Therefore, a comprehensive thermal network of the engine based on the lumped capacity method has been developed. The model allows the computation of component temperatures in steady state operation as well as in transient engine studies, e.g. investigations of engine warm-up. The model is integrated in a co-simulation environment consisting of a detailed vehicle and engine cycle simulation code. The paper describes the procedure of the co-simulation and presents several examples of warm-up simulations.

The 3D CFD method has become an essential and reliable tool for the development of modern large gaseous-fuelled engines. This holds especially true for the optimization of mixture formation and charge motion in prechamber engines to ensure suitable conditions near the spark plug at ignition time. In order to initialize a quick combustion process, an ignitable mixture with high turbulence but moderate velocity must prevail round the spark plug. However, suitable models for combustion and heat transfer are inevitable for a realistic simulation of the whole engine cycle. Within 3D CFD codes the combustion process is usually calculated using the PDF (probability density function) - model; heat transfer is modeled based on the logarithmic wall function. Experimental investigations were carried out on a single cylinder research engine in order to validate the combustion model used and different heat transfer models.

Using natural gas as a fuel in internal combustion engines is a promising way to obtain efficient power generation with relatively low environmental impact. Dual fuel operation is especially interesting because it can combine the safety and reliability of the basic diesel concept with fuel flexibility. To deal with the greater number of degrees of freedom caused by the interaction of two fuels and combining different combustion regimes, it is imperative to use simulation methods in the development process to gain a better understanding of the combustion behavior. This paper presents current research into ignition and combustion of a premixed natural gas/air charge with a diesel pilot spray in a large bore diesel ignited gas engine with a focus on 3D-CFD simulation. Special attention was paid to injection and combustion. The highly transient behavior of the diesel injector especially at small injection quantities poses challenges to the numerical simulation of the spray.

It is critical for gas and dual fuel engines to have improved transient characteristics in order that they can successfully compete with diesel engines. Testing of transient behavior as well as of different control strategies for the multi-cylinder engine (MCE) should already be done on the single cylinder engine (SCE) test bed during the development process. This paper presents tools and algorithms that simulate transient MCE behavior on a SCE test bed. A methodology that includes both simulation and measurements is developed for a large two-stage turbocharged gas engine. Simple and fast models and algorithms are created that are able to provide the boundary conditions (e.g., boost pressure and exhaust back pressure) of a multi-cylinder engine in transient operation in real-time for use on the SCE test bed. The main models of the methodology are discussed in detail.

The reduction of CO₂ emissions represents a major goal of governments worldwide. In developed countries, approximately 20% of the CO₂ emissions originate from transport, one third of this from commercial vehicles. CO₂ emission legislation is in place for passenger cars in a number of major markets. For commercial vehicles such legislation was also already partly published or is under discussion. Furthermore the commercial vehicles market is very cost sensitive. Thus the major share of fuel cost in the total cost of ownership of commercial vehicles was already in the past a major driver for the development of efficient drivetrain solutions. These aspects make the use of new powertrain technologies, specifically hybridization, mandatory for future commercial powertrains. While some technologies offer a greater potential for CO₂ reduction than others, they might not represent the overall optimum with regard to the total cost of ownership.

Further fuel efficiency improvements are mandatory in order to achieve the CO2 emission limits envisaged in the future. Electrification of the powertrain is seen as one of the key technologies to achieve these future goals. However, electrification of the power train typically goes with a massive cost increase of the overall system itself which is especially crucial for cost sensitive markets like India. AVL's approach to cost reduction for comparable performance and fuel consumption target values is an integration of functions. This paper demonstrates that, through a deeper interaction of the single powertrain components, further fuel efficiency optimization may be gained. System optimization at a powertrain level enables the achievement of future powertrain targets with respect to fuel efficiency and performance with only minimal and reduced requirements at a component level (i.e. combustion engine, electric drive, transmission and battery).

Hydrogen is seen as a promising energy carrier for a future mobility scenario. Applied as fuel in IC engines with internal mixture formation, hydrogen opens up new vistas for the layout of the combustion system. The 3D CFD simulation of internal mixture formation as well as combustion helps to understand the complex in-cylinder processes and provides a powerful tool to optimize the engine's working cycle. The performance of standard simulation models for mixture formation as well as the performance of a user-defined combustion model applied in a commercial CFD-code is discussed within this article. The 3D CFD simulations are validated with measurements obtained from a thermodynamic and from an optical research engine respectively.

In this paper a zero-dimensional simulation methodology for efficient pre-optimization of the combustion process in DI diesel engines is presented. A new model for the calculation of the rate of heat release is unveiled. It is based on the separate description of both the primary processes closely related to the fuel jet as well as the following combustion of the fuel mass remaining after the end of injection. The modeling of fuel mass distribution between premixed and diffusion combustion as well as a model for the fuel preparation time are explained. Furthermore, models for the calculation of ignition delay and premixed combustion based on an extended Arrhenius formulation are discussed, as well as turbulent combustion on the basis of a Magnussen model. The new features of the heat release model prove to be necessary to describe the effects of modern high-pressure fuel injection systems on the combustion process regarding the strong influence of the injection rate on the burn rate.

To increase reliability and the maintenance interval of an internal combustion engine while operating it with the lowest possible emissions, spark plug wear must be reduced. In this context, information about the spark plug center and the ground electrode temperature is key. Several measurement devices have been developed that measure the temperature of spark plug electrodes. The great challenge is to measure the temperature of the center electrode; on the one hand, the measurement device must be insulated and capable of withstanding the high voltage of the ignition system, and on the other hand, the device should not influence the ignition system. All previously studied devices presented in this paper have in common that major reconstruction of the ignition system and/or spark plugs whose design is very different from the standard engine spark plug were necessary.

This paper shows extracts from the development process of a lean-burn gaseous fuelled engine for combined heat and power generation. The aim was to optimize the mixture formation, the charge motion and the combustion of an existing multi-cylinder engine. Therefore, experimental investigations on a single cylinder research engine and numerical simulations based on 3-dimensional CFD methods were carried out. The use of CFD methods for the optimization of the engine required intensive development efforts in the field of combustion simulation. In particular, the combustion model developed by Magnussen and Hjertager [1] was modified. Through comparison with the PDF model and results of the engine process calculation, the suitability of this modified combustion model was shown. In addition, a knock model was also developed and implemented in the CFD code in order to determine the knock tendency of different engine concepts.

This paper summarizes the results of several investigations on in-cylinder heat transfer during high-pressure and gas exchange phases as well as heat transfer in the inlet and outlet ports for a number of different engine types (DI Diesel, SI and gaseous fueled engine). The paper contains a comparision of simulation results and experimental data derived from heat flux measurements. Numerical results were obtained from zero-, one- and three-dimensional simulation methods. Time and spatially resolved heat fluxes were measured applying the surface temperature method and special heat flux sensors. The paper also includes an assessment of different sensor types with respect to accuracy and applicability.

Using natural gas in large bore engines reduces carbon dioxide emissions by up to 25% at a lower fuel cost than diesel engines. In demanding applications with highly transient operating profiles, however, premix gas engines have disadvantages compared to diesel engines because of the potential for knocking and misfire to occur. Operating a gas engine using the diesel cycle requires high gas injection pressures. Furthermore, a source of ignition is needed due to the high autoignition temperature of methane. State-of-the-art solutions inject a small quantity of diesel fuel before introducing the natural gas. One monofuel alternative ignites the gas jets with flame torches that originate in a prechamber. This paper presents the simulation based development of a prechamber ignited high pressure direct injection (HPDI) gas combustion concept and subsequent experimental validation.