Search Results

The performance of an organic Rankine cycle (ORC) that recovers heat from the exhaust of a heavy-duty diesel engine was simulated. The work was an extension of a prior study that simulated the performance of an experimental ORC system developed and tested at Oak Ridge National laboratory (ORNL). The experimental data were used to set model parameters and validate the results of that simulation. For the current study the model was adapted to consider a 15 liter turbocharged engine versus the original 1.9 liter light-duty automotive turbodiesel studied by ORNL. Exhaust flow rate and temperature data for the heavy-duty engine were obtained from Southwest Research Institute (SwRI) for a range of steady-state engine speeds and loads without EGR. Because of the considerably higher exhaust gas flow rates of the heavy-duty engine, relative to the engine tested by ORNL, a different heat exchanger type was considered in order to keep exhaust pressure drop within practical bounds.

Laminar flow elements (LFEs) are commonly used to measure the flow rate of gases in various flow streams. Since LFEs operate on the principle of fully developed laminar pipe flow, the viscosity of the gas must be known. In many cases, the flowing gas is air of varying humidity, inlet temperature, and inlet pressure. While the viscosity of humid air has been studied extensively over the past 60+ years, the effects of humidity have not been consistently accounted for in the literature and industry documentation pertaining to LFE operation, and this can lead to errors. Additionally, the available LFE operational documentation is not presented in equation form; rather it is provided in tables and graphs which do not facilitate automation of the flow calculations during data acquisition. This paper provides a brief review of the available data and correlations for the viscosity of humid air and its application to the calculation of air flow rate using a laminar flow element.

As natural gas engines are designed to operate leaner and with increased boost pressure, durability of the spark plugs becomes problematic. Among the various new ignition devices that have been considered to solve some of the problems facing spark plugs, railplugs appear to hold clear advantages in some areas. There are two types of railplugs: coaxial rail and parallel rail. This paper reports the results of an experimental study of various parameters that affect the performance of parallel railplugs. Their performance was quantified by the distance that the arc traveled along the rails from the initiation point. Travel along the rails is thought to be an important performance metric because rail-travel limits excessive local wear and produces a distributed ignition source which can potentially reduce mixture inhomogeneity induced ignition problems.

The Rotating Liner Engine (RLE) concept is a design concept for internal combustion engines, where the cylinder liner rotates at a surface speed of 2-4 m/s in order to assist piston ring lubrication. Specifically, we have evidence from prior art and from our own research that the above rotation has the potential of eliminating the metal-to-metal contact/boundary friction that exists close to the piston reversal areas. This frictional source becomes a significant energy loss, especially in the compression/expansion part of the cycle, when the gas pressure that loads the piston rings and skirts is high. This paper describes the Diesel RLE prototype constructed from a Cummins 4BT and the preliminary observations from initial low load testing. The critical technical challenge, namely the rotating liner face seal, appears to be operating with negligible gas leakage and within the hydrodynamic lubrication regime for the loads tested (peak cylinder pressures of the order of 80 bar).

This study extends a previous study on the effects of intake throttling and post-injection on light-duty Diesel engine exhaust temperatures and emissions, and includes the effects of EGR, in-cylinder swirl air motion, and cylinder deactivation. The baseline injection strategy was adapted from a 2014 Chevrolet Cruze having an engine similar to the light-duty GM engine used for this study. While the engine was fixed to a motoring engine dynamometer, the dynamometer was not active for the study, as the engine was operated under idle conditions. The desired idle speed was controlled using a feedback loop in the control algorithm to vary the duration of the main injection event. Three methods were investigated. In the first method, the engine was operated fully warmed up, firing all four cylinders.

Time-resolved current and voltage measurements for an inductive automotive spark system were made. Also presented are measurements of the total energy delivered to the spark gap. The measurements were made in air for a range of pressures from 1-18 atm, at ambient temperatures. The measured voltage and current characteristics were found to be a function of many ignition parameters; some of these include: spark gap distance, internal resistance of the spark plug and high tension wire, and pressure. The voltages presented were measured either at the top of the spark plug or at the spark gap. The measurements were made at different time resolutions to more accurately resolve the voltage and current behavior throughout the discharge process. This was necessary because the breakdown event occurs on a time scale much shorter than the arc and glow phases.

A multi-dimensional cathode spot generation model is proposed to study the interaction between the plasma arc and cathode surface of a spark plug during the ignition process. The model is focused on the instationary (high current) arc phase immediately following breakdown, and includes detailed physics for the phenomena during spot formation such as ion collision, thermal-field emission, and metal vaporization, to simulate the surface heat source, current density and surface pressure. The spot formation for a platinum cathode is simulated using the VOF (volume of fluid) model within FLUENT, where the local metal is melted and deformed by pressure differences on the surface. A random walk model has been integrated to consider the movement of the arc center, resulting in the formation of different types of spots.