Criteria

Text:
Display:

Results

Viewing 1 to 30 of 67740
2011-05-17
Journal Article
2011-01-1649
Andrew J. Morello, Jason R. Blough, Jeffrey Naber, Libin Jia
Research into the estimation of diesel engine combustion metrics via non-intrusive means, typically referred to as “remote combustion sensing” has become an increasingly active area of combustion research. Success in accurately estimating combustion metrics with low-cost non-intrusive transducers has been proven and documented by multiple sources on small scale diesel engines (2-4 cylinders, maximum outputs of 67 Kw, 210 N-m). This paper investigates the application of remote combustion sensing technology to a larger displacement inline 6-cylinder diesel with substantially higher power output (280 kW, 1645 N-m) than previously explored. An in-depth frequency analysis has been performed with the goal of optimizing the estimated combustion signature which has been computed based upon the direct relationship between the combustion event measured via a pressure transducer, and block vibration measured via accelerometers.
2011-05-17
Technical Paper
2011-01-1644
Greg Uhlenhake, Ahmet Selamet, Kevin Fogarty, Kevin Tallio, Philip Keller
A cold turbocharger test facility was designed and developed at The Ohio State University to measure the performance characteristics under steady state operating conditions, investigate unsteady surge, and acquire acoustic data. A specific turbocharger is used for a thermodynamic analysis to determine the capabilities and limitations of the facility, as well as for the design and construction of the screw compressor, flow control, oil, and compression systems. Two different compression system geometries were incorporated. One system allows compressor performance measurements left of the surge line, while the other incorporates a variable-volume plenum. At the full plenum volume and a specific impeller tip speed, the temporal variation of the compressor inlet and outlet and the plenum pressures as well as the turbocharger speed is presented for stable, mild surge, and deep surge operating points.
2011-05-17
Technical Paper
2011-01-1645
Michael Browne
Test Facilities for Vibrations and Acoustics can be very complicated. With the addition of necessary high power motor dynamometers for load application, the complexity of the test cell increases dramatically. The motors and subsequent additional fixtures and shafts necessary to apply loading conditions can produce additional source noises that would interfere with test measurements. In addition, facility interfaces can dramatically influence the test cell setup and reduce the measurement capabilities. This paper addresses common considerations needed in considering a new test cell for driveline vibration, acoustics, efficiency, and durability testing using motored dynamometers. In addition to outlining common design points, a practical application of 2 new dynamometers utilized for vibration, acoustics, efficiency, and durability testing and their subsequent capabilities are outlined.
2011-05-17
Technical Paper
2011-01-1660
Ienkaran Arasaratnam, Saeid Habibi, Christopher Kelly, Tony J. Fountaine, Jimi Tjong
Advanced engine test methods incorporate several different sensing and signal processing techniques for identifying and locating manufacturing or assembly defects of an engine. A successful engine test method therefore, requires advanced signal processing techniques. This paper introduces a novel signal processing technique to successfully detect a faulty internal combustion engine in a quantitative manner. Accelerometers are mounted on the cylinder head and lug surfaces while vibration signals are recorded during engine operation. Using the engine's cam angular position, the vibration signals are transformed from the time domain to the crank-angle domain. At the heart of the transformation lies interpolation. In this paper, linear, cubic spline and sinc interpolation methods are demonstrated for reconstructing vibration signals in the crank-angle domain.
2011-05-17
Technical Paper
2011-01-1662
Chad Walber, Jason R. Blough, Mark Johnson, Carl Anderson
When testing dynamic structures, it is important to note that the dynamic system in question may be submerged into a fluid during operation and to properly test the structure under the same condition in order to understand the true dynamic parameters of the system. In this way, the mass and stiffness coupling to the particular fluid, for the case of this study, automatic transmission fluid, may be taken into account. This is especially important in light structures where the coupling between the fluid mass and the structural mass may be great. A structure was tested with a laser vibrometer using several impact methods in open air to determine which impact method would be most suitable for submerged testing. The structure was then submerged in transmission fluid with an accelerometer attached and subsequently tested and compared to the previous results.
2011-05-17
Technical Paper
2011-01-1619
Shi Zheng, Chris Kleinfeld
This paper presents a hybrid method that predicts the whistle occurrence of an automotive exhaust tuning device. The method utilizes inputs from a limited amount of test work or numerical simulation to predict the whistle occurrence in a wider range of flow conditions (temperature and velocity). It has the advantages of being quick and low cost compared with extensive tests or the computational fluid dynamics approach.
2011-05-17
Technical Paper
2011-01-1639
Jan Krueger, Michael Pommerer, Tom Frei
In the past years Eberspaecher has installed Active Exhaust Silencers on several passenger vehicles with different diesel and gasoline engines on a prototype level. Meanwhile, a substantial reduction of the exhaust noise is regularly achieved in a broad frequency range covering all relevant engine orders. Due to the higher acoustic excitation and higher exhaust temperatures in gasoline engines it is more difficult to implement the ANC-technology on those engines. However, results from roller test benches focus on the acoustic performance as well as weight and volume reductions and demonstrate a marked improvement which was achieved with gasoline engines too. Further progress was made in the development of the durability and industrialization of all relevant components of the system. Finally, current design trends and possible fields of application will be discussed.
2011-05-17
Journal Article
2011-01-1635
Mingfeng Li, Jie Duan, Teik Lim
Gears are essential parts of many precision power and torque transmitting machines. However, the radiated intensive tonal noise due to the gear meshing is highly undesirable and annoying. In very severe cases, the gear vibrations can reduce the life and performance of the power transmitting components. Typical gearbox vibration and sound spectra contain several dominant narrowband tonal signals that are mixed in with a lower level broadband response signals. Hence, the control of mesh response of gearbox housing belongs to the problem of the rejection or cancellation of periodical disturbance. The frequencies of these tonal signals are related to the number of teeth and rotation speed, and highly predictable. Thus, a feedforward control system was normally adopted. In most of existed applications, an accurate reference based on the frequency information of tachometer pulse train signal is required for this kind of control system.
2011-05-17
Technical Paper
2011-01-1636
Chiharu Togashi PhD, Mitsuo Nakano PhD, Masao Nagai PhD
A lot of countermeasures have been developed in order to reduce interior noise. For example, improvements of rubber mount characteristics and other measures have been implemented. Recently electromagnetic active engine mounts based on a hydraulic engine mount have been developed. They are significantly effective for the reduction of the booming noise which is unpleasant for passengers. Although the LMS algorithm has been generally used for the active control, it has been used only for reducing booming noise. The authors developed a new control method in order to reduce not only the booming noise but also the noise and the vibration over wide frequency band for comfortable vehicle interior space. The authors studied the method which determines the feedback gain according to various conditions by modifying LMS algorithm. In this modified LMS algorithm, only an error signal was used as an input signal.
2011-05-17
Technical Paper
2011-01-1565
Jennifer Durfy, Sang-Bum Hong, Bibhu Mahanta
As fuel prices continue to be unstable the drive towards more fuel efficient powertrains is increasing. For engine original equipment manufacturers (OEMs) this means engine downsizing coupled with alternative forms of power to create hybrid systems. Understanding the effect of engine downsizing on vehicle interior NVH is critical in the development of such systems. The objective of this work was to develop a vehicle model that could be used with analytical engine mount force data to predict the vehicle interior noise and vibration response. The approach used was based on the assumption that the largest contributor to interior noise and vibration below 200 Hz is dominated by engine mount forces. An experimental transfer path analysis on a Dodge Ram 2500 equipped with a Cummins ISB 6.7L engine was used to create the vehicle model. The vehicle model consisted of the engine mount forces and vehicle paths that define the interior noise and vibration.
2011-05-17
Technical Paper
2011-01-1564
Tony Karlsson, Ragnar Glav
Simulation using basic acoustic 2-port elements is a time effective method for prediction of the attenuation of single components as well as of complete exhaust aftertreatment and silencer systems. However, with the complexity of current systems, the transformation from design geometries to networks of basic elements is not straightforward. In this paper a practical example of the modelling of a modern exhaust aftertreatment system is presented. A silencer aimed at the Euro 6 heavy duty emissions legislation containing complex flow turnings, parallel branches, DOC (Diesel Oxidation Catalyst), DPF (Diesel Particulate Filter) and SCR (Selective Catalytic Reduction) catalysts was modelled. Evaluation against measurements in order to understand the influence of the different acoustic elements upon overall attenuation and to improve the model with respect to near field and higher order mode effects was done.
2011-05-17
Technical Paper
2011-01-1563
Ki-Hwa Lee, Chung-Guen Nam, Hyung-Shin KIm, Dong-Kyu Yoo, Koo-Tae Kang
A comprehensive investigation was carried out in order to develop the idle sound quality for diesel V6 engine when the engine development process is applied to power-train system, which included new 8-speed automatic transmission for breaking down the noise contribution between the mechanical excitation and the combustion excitation. First of all, the improvement of dynamic characteristic can be achieved during the early stages of the engine development process using experimental modal analysis (EMA) & the robust design of each engine functional system. In addition, the engine structural attenuation (SA) is enhanced such that the radiated combustion noise of the engine can be maintained at a target level even with an increased combustion excitation. It was found that the engine system has better parts and worse parts in frequency range throughout the SA analysis. It is important that weak points in the system should be optimized.
2011-05-17
Journal Article
2011-01-1562
Tamer Elnady, Sara Elsaadany, D. W. Herrin
Diesel engines produce harmful exhaust emissions and high exhaust noise levels. One way of mitigating both exhaust emissions and noise is via the use of after treatment devices such as Catalytic Converters (CC), Selective Catalytic Reducers (SCR), Diesel Oxidation Catalysts (DOC), and Diesel Particulate Filters (DPF). The objective of this investigation is to characterize and simulate the acoustic performance of different types of filters so that maximum benefit can be achieved. A number of after treatment device configurations for trucks were selected and measured. A measurement campaign was conducted to characterize the two-port transfer matrix of these devices. The simulation was performed using the two-port theory where the two-port models are limited to the plane wave range in the filter cavity.
2011-05-17
Technical Paper
2011-01-1571
Myung-Gyu Kim
The expectation of customers on ride comfort is very high and vehicle engineers also have keen interesting to improve ride vibration and road noise. As the conventional tuning parameters for the ride vibration and road noise, vibration characteristics of tire, body structure, bushing, suspension members etc. are mainly considered. But these conventional tuning parameters are sometimes not enough due to the side effects such like handling performances and durability. Therefore, instead of these conventional design and tuning parameters, suspension geometry and alignment characteristics of suspension system are selected as the alternative parameters to compromise ride vibration, road noise and vehicle dynamic performance. In this research, multi-link type rear suspension is selected for the integrated analysis of ride vibration, road impact noise and handling performance.
2011-05-17
Journal Article
2011-01-1568
Christian Fernholz, Ronald Perri, David Watts, David Willmer, Jeff Williams
This paper discusses the optimization of an automotive hydraulic steering pump pulley design for improved in-vehicle pump NVH performance. Levels of steering pump whine noise heard inside a vehicle were deemed objectionable. Vehicle and component transfer path analyses indicated that the dominant noise path for the whine noise was airborne in nature. Subsequent experimental modal analysis indicated that the steering pump pulley was a major contributor to the amount of radiated noise produced by the pump/pulley system. CAE analysis was used to further analyze the dynamic behavior of the pulley and develop an optimized design with decreased noise radiation efficiency. The results predicted with the CAE analysis were verified in-vehicle, resulting in a vehicle with acceptable steering pump whine noise performance.
2011-05-17
Technical Paper
2011-01-1566
Thomas Reinhart, Mitchel Smolik
Several new or significantly upgraded heavy duty truck engines are being introduced in the North American market. One important aspect of these new or revised engines is their noise characteristics. This paper describes the noise related characteristics of the new DD15 engine, and compares them to other competitive heavy truck engines. DD15 engine features relevant to noise include a rear gear train, isolated oil pan and valve cover, and an amplified high pressure common rail fuel system. The transition between non-amplified and amplified common rail operation is shown to have a significant noise impact, not unlike the transition between pilot injection and single shot injection in some other engines.
2011-05-17
Technical Paper
2011-01-1576
Stefan Bernsteiner, Daniel Wallner
Experimental researches on brake squeal have been performed since many years in order to get an insight into friction-excited vibrations and squeal triggering mechanisms. There are many different possibilities to analyse brake squeal. The different operating deflection shapes can be detected using e.g. laser vibrometer systems or acceleration sensors. Piezoelectric load cells can be used for the measurement of the normal contact force of the brake pad. The presented test setup measures not only the mean value of the friction force between brake pad and disc at a certain brake pressure, but also the superposed vibration of this force, which only occurs during a squeal event. Therefore the guide pins of the brake caliper are replaced by modified ones. The brake pads are held in position by these pins and the resulting force of the brake torque, hence the friction force, acts on these pins. The shape of the pins is optimized for measuring these forces.
2011-05-17
Journal Article
2011-01-1575
John David Fieldhouse, David Bryant, Chris John Talbot
Thermo-elastic and thermo-plastic behaviour takes place with a disc brake during heavy braking and it is this aspect of braking that this paper considers. The work is concerned with working towards developing design advice that provides uniform heating of the disc, and equally important, even dissipation of heat from the disc blade. The material presented emanates from a combination of modeling, on-vehicle testing but mainly laboratory observations and subsequent investigations. The experimental work makes use of a purpose built high speed brake dynamometer which incorporates the full vehicle suspension for controlled simulation of the brake and vehicle operating conditions. Advanced instrumentation allows dynamic measurement of brake pressure fluctuations, disc surface temperature and discrete vibration measurements.
2011-05-17
Technical Paper
2011-01-1574
Eric Denys
The development and validation of a brake pad insulator damping measurement procedure by the SAE Brake NVH Standards Committee was presented at the 2010 SAE Brake Colloquium (Paper 2010-01-1685). In Europe, in 2010, the EKB Working Group identified the need to develop a similar procedure, and started some activities which lead to the release of a standard similar but different than the SAE J3001. The SAE and EKB working groups agreed that having a global standard was of paramount importance, so the 2 groups decided to meet in November of 2010 to flush out the details of the J3001 global procedure. The details of the new test procedure, test setup and recommendation for proper test practices are described in this paper. This description provides an excellent foundation for evaluating the insulator damping properties over a range of temperatures and frequencies.
2011-05-17
Technical Paper
2011-01-1581
Z. C. Feng, Perry Gu
Tire cavity noise refers to the vehicle noise due to the excitation of the acoustic modes of a tire air cavity. Although two lowest acoustic modes are found to be sufficient to characterize the cavity dynamics, the dynamical response of these two modes is complicated by two major factors. First, the tire cavity geometry is affected by the static load applied to the tire due to vehicle weight. Second, the excitation force from the tire-road contact changes position as the tire rotates. In this paper, we first develop dynamic equations for the lowest cavity modes of a rotating tire under the static load. Based on the model, we obtain the forces transmitted to the wheel from the tire resulting from the random contact force between the tire and the road surface. The transmitted forces along the fore/aft direction and the vertical direction show two peaks at frequencies that are dependent both on the tire static load and on the vehicle speed.
2011-05-17
Technical Paper
2011-01-1579
Takashi Nakae, Takahiro Ryu, Atsuo Sueoka
This paper deals with low-frequency squeal phenomena generated in floating type of car disc brake units. First, the vibration characteristics of low-frequency squeal (about 2 kHz) were investigated. Here, in order to reproduce the squeal, a bench-test apparatus consisting of an actual automotive disc brake unit was utilized, itself comprising a disc, pad, and caliper. With this, the associated frequency characteristics were experimentally determined. It was found that the squeal is caused by coupled out-of-plane vibration modes among the disc and caliper due to Coulomb friction. As an experimental countermeasure, a dynamic absorber was applied to the leading side or the trailing side of the inner caliper. It was found that squeal can be suppressed when the natural frequency of the dynamic absorber is tuned so as to be near the frequency of the squeal, and that squeal can be suppressed even without viscous damping of the dynamic absorber.
2011-05-17
Technical Paper
2011-01-1580
Mohamad S. Qatu, Roger King, Omar Shubailat, Rachel Wheeler
Variability in design (e.g. tolerance), material, manufacturing, or other sources of variation causes significant variation in vehicle noise, vibration and harshness (NVH) response. This leads to a higher percentage of produced vehicles with higher levels of NVH leading to higher number of warranty claims and loss of customer satisfaction, which are proven costly to the original equipment manufacturers (OEM). Measures must be taken to insure less warranty claims and higher levels of customer satisfaction. As a result, original equipment manufacturers have implemented design for variation in the design process to secure an acceptable (or within specification) response. We will focus on some aspects of design variations in a tire/wheel assembly that should be considered in the design process. In particular, certain materials (e.g. rubber) are known to have variation in stiffness that is either unavoidable or proven costly if tighter control is desired.
2011-05-17
Technical Paper
2011-01-1584
Christian M. Fernholz
The present work discusses an objective test and analysis method developed to quickly quantify steering gear rattle noise heard in a vehicle. Utilizing envelope analysis on the time history data of the rattle signal, the resulting method is simple, fast, practical and yields a single-valued metric which correlates well to subjective measures of rattle noise. In contrast to many other rattle analysis methods, the approach discussed here is completed in the time domain. As applied to rattle noise produced by automotive electric steering systems, the metric produced with this analysis method correlates well with subjective appraisals of vehicle-level rattle noise performance. Lastly, this method can also be extended to rattle measurements at the component and subcomponent level.
2011-05-17
Technical Paper
2011-01-1577
John David Fieldhouse, David Bryant, Chris John Talbot
The paper overviews the modes of vibration of the principal component parts of a brake and their contribution to system instability during noise generation. It is shown that both in-plane and out-of-plane vibration are present and that both can be related to the vibration of the pad. It is further shown that the pad and its region often provide a solution or “fix” towards noise prevention and it is this area that forms the focus of this investigation. The collective evidence, proposals and associated theory are applied to real brake case studies when it is demonstrated that disc/pad interface “spragging” may be the source of brake noise. Measurements of the position of the dynamic centre of pressure (CoP) support the theoretical predictions that a leading CoP induces brake noise. Design proposals are suggested that may be applied early in the design phase as a means to reduce the propensity of a brake to generate noise.
2011-05-17
Journal Article
2011-01-1582
Paul R. Donavan, Alan Parrett, Dave Nielubowicz, Jinshuo Zhu
Developing common methods of noise evaluation and facilities can present a number of challenges in the area of tire/pavement noise. Some of the issues involved include the design and construction of pavements globally, the change in pavement over time, and variation in the noise produced with standard test tires used as references. To help understand and address these issues for airborne tire/pavement noise, acoustic intensity measurement methods based on the On-board Sound Intensity (OBSI) technique have been used. Initial evaluations have included measurements conducted at several different proving grounds. Also included were measurements taken on a 3m diameter tire noise dynamometer with surfaces replicating test track pavements. Variation between facilities appears to be a function of both design/construction and pavement age. Consistent with trends in the literature, for smooth asphalt surfaces, the newest surface produced levels lower than older surfaces.
2011-05-17
Technical Paper
2011-01-1586
Malika Perera, Stephanos Theodossiades, Homer Rahnejat, Patrick Kelly
Modern automotive industry is driven by improved fuel efficiency, whilst simultaneously increasing output power and reducing size/weight of vehicle components. This trend has the drawback of inducing various Noise, Vibration and Harshness (NVH) concerns in the drivetrain, since fairly low energy excitation often suffices to excite natural modes of thin walled structures, such as the transmission bell housing. Transmission rattle is one of the many undesired NVH issues, originating from irregularities in engine torque output. The crankshaft speed fluctuations are transferred through the transmission input shaft. Transmission compactness also allows repetitive interaction of conjugate loose gear pairs. The engine fluctuations disturb the otherwise unintended, but orderly meshing of these loose gears. This often leads to radiation of a characteristic air-borne noise from the impact sites.
2011-05-17
Technical Paper
2011-01-1591
Kumbhar S. Mansinh, Atul Miskin, Vishal Vasantrao Chaudhari, Ashish Rajput
The noise and vibration performance of diesel fueled automotives is critical for overall customer comfort. The stationary vehicle with engine running idle (Vehicle Idle) is a very common operating condition in city driving cycle. Hence it is most common comfort assessment criteria for diesel vehicles. Simulations and optimization of it in an early stage of product development cycle is priority for all OEMs. In vehicle idle condition, powertrain is the only major source of Noise and Vibrations. The key to First Time Right Idle NVH simulations and optimization remains being able to optimize all Transfer paths, from powertrain mounts to Driver Ear. This Paper talks about the approach established for simulations and optimization of powertrain forces entering in to frame by optimizing powertrain mount hard points and stiffness. Powertrain forces optimized through set process are further used to predict the vehicle passenger compartment noise and steering vibrations.
2011-05-17
Technical Paper
2011-01-1600
Theo Geluk, Peter Van der Linden, Davide Vige', Massimo Caudano, Simone Gottardi, Fabio Ciraolo, Hamid Mir
Road-tire induced vibrations are in many vehicles determining the interior noise levels in (semi-) constant speed driving. The understanding of the noise contributions of different connections of the suspension systems to the vehicle is essential in improvement of the isolation capabilities of the suspension- and body-structure. To identify these noise contributions, both the forces acting at the suspension-to-body connections points and the vibro-acoustic transfers from the connection points to the interior microphones are required. In this paper different approaches to identify the forces are compared for their applicability to road noise analysis. First step for the force identification is the full vehicle operational measurement in which target responses (interior noise) and indicator responses (accelerations or other) are measured.
2011-05-17
Technical Paper
2011-01-1601
Abolfazl Eskandari, Mostafa haghroosta, Kia Valefi
One of the most important factors that must be taken into account during vehicle design is the quality of noise and vibration produced by the vehicle. This is evident from manufacturer's attempt to produce quieter product. On the other hand, some of the vehicles have not good NVH properties and must be modified in order to be successful in the market. In this type of vehicles, no basic changes can be made, and focus must be on restricted improvements. In this research, a vehicle of this kind is selected and measures have been taken to improve its noise and vibration behavior. By implementing suspension techniques, some of the vibration characteristics of drive train and its influence on the interior noise at different engine speeds and under road load have been investigated. In addition, the effect of double layer instead of single layer muffler skin on the cabin noise has been probed.
2011-05-17
Technical Paper
2011-01-1528
Deepak Rana, Felix Regin, Mohan Makana
A muffler or silencer is an integral part of the exhaust system and is a device used to prevent sound from reaching the openings of the exhaust duct and radiating as far field noise. Different acoustical design and analysis techniques are used to predict the acoustical performance of exhaust systems. Flow noise from exhaust tail pipe is one of the major noise sources in a vehicle. Flow noise is generated mainly during fast acceleration operating condition due to complex flow behavior. In this paper, we have studied the detailed flow field and tried to establish an analyses procedure for flow noise prediction. The flow analysis is carried out in commercial CFD solver Star CCM+. The transient engine boundary conditions are obtained from the experimental testing. The flow noise generated from the muffler was calculated by acoustic analogy of Lighthill using the above boundary conditions.
Viewing 1 to 30 of 67740

Filter

  • Range:
    to:
  • Year: