Criteria

Text:
Display:

Results

Viewing 1 to 30 of 52570
2011-05-17
Journal Article
2011-01-1649
Andrew J. Morello, Jason R. Blough, Jeffrey Naber, Libin Jia
Research into the estimation of diesel engine combustion metrics via non-intrusive means, typically referred to as “remote combustion sensing” has become an increasingly active area of combustion research. Success in accurately estimating combustion metrics with low-cost non-intrusive transducers has been proven and documented by multiple sources on small scale diesel engines (2-4 cylinders, maximum outputs of 67 Kw, 210 N-m). This paper investigates the application of remote combustion sensing technology to a larger displacement inline 6-cylinder diesel with substantially higher power output (280 kW, 1645 N-m) than previously explored. An in-depth frequency analysis has been performed with the goal of optimizing the estimated combustion signature which has been computed based upon the direct relationship between the combustion event measured via a pressure transducer, and block vibration measured via accelerometers.
2011-05-17
Technical Paper
2011-01-1644
Greg Uhlenhake, Ahmet Selamet, Kevin Fogarty, Kevin Tallio, Philip Keller
A cold turbocharger test facility was designed and developed at The Ohio State University to measure the performance characteristics under steady state operating conditions, investigate unsteady surge, and acquire acoustic data. A specific turbocharger is used for a thermodynamic analysis to determine the capabilities and limitations of the facility, as well as for the design and construction of the screw compressor, flow control, oil, and compression systems. Two different compression system geometries were incorporated. One system allows compressor performance measurements left of the surge line, while the other incorporates a variable-volume plenum. At the full plenum volume and a specific impeller tip speed, the temporal variation of the compressor inlet and outlet and the plenum pressures as well as the turbocharger speed is presented for stable, mild surge, and deep surge operating points.
2011-05-17
Technical Paper
2011-01-1660
Ienkaran Arasaratnam, Saeid Habibi, Christopher Kelly, Tony J. Fountaine, Jimi Tjong
Advanced engine test methods incorporate several different sensing and signal processing techniques for identifying and locating manufacturing or assembly defects of an engine. A successful engine test method therefore, requires advanced signal processing techniques. This paper introduces a novel signal processing technique to successfully detect a faulty internal combustion engine in a quantitative manner. Accelerometers are mounted on the cylinder head and lug surfaces while vibration signals are recorded during engine operation. Using the engine's cam angular position, the vibration signals are transformed from the time domain to the crank-angle domain. At the heart of the transformation lies interpolation. In this paper, linear, cubic spline and sinc interpolation methods are demonstrated for reconstructing vibration signals in the crank-angle domain.
2011-05-17
Technical Paper
2011-01-1636
Chiharu Togashi PhD, Mitsuo Nakano PhD, Masao Nagai PhD
A lot of countermeasures have been developed in order to reduce interior noise. For example, improvements of rubber mount characteristics and other measures have been implemented. Recently electromagnetic active engine mounts based on a hydraulic engine mount have been developed. They are significantly effective for the reduction of the booming noise which is unpleasant for passengers. Although the LMS algorithm has been generally used for the active control, it has been used only for reducing booming noise. The authors developed a new control method in order to reduce not only the booming noise but also the noise and the vibration over wide frequency band for comfortable vehicle interior space. The authors studied the method which determines the feedback gain according to various conditions by modifying LMS algorithm. In this modified LMS algorithm, only an error signal was used as an input signal.
2011-05-17
Technical Paper
2011-01-1565
Jennifer Durfy, Sang-Bum Hong, Bibhu Mahanta
As fuel prices continue to be unstable the drive towards more fuel efficient powertrains is increasing. For engine original equipment manufacturers (OEMs) this means engine downsizing coupled with alternative forms of power to create hybrid systems. Understanding the effect of engine downsizing on vehicle interior NVH is critical in the development of such systems. The objective of this work was to develop a vehicle model that could be used with analytical engine mount force data to predict the vehicle interior noise and vibration response. The approach used was based on the assumption that the largest contributor to interior noise and vibration below 200 Hz is dominated by engine mount forces. An experimental transfer path analysis on a Dodge Ram 2500 equipped with a Cummins ISB 6.7L engine was used to create the vehicle model. The vehicle model consisted of the engine mount forces and vehicle paths that define the interior noise and vibration.
2011-05-17
Technical Paper
2011-01-1563
Ki-Hwa Lee, Chung-Guen Nam, Hyung-Shin KIm, Dong-Kyu Yoo, Koo-Tae Kang
A comprehensive investigation was carried out in order to develop the idle sound quality for diesel V6 engine when the engine development process is applied to power-train system, which included new 8-speed automatic transmission for breaking down the noise contribution between the mechanical excitation and the combustion excitation. First of all, the improvement of dynamic characteristic can be achieved during the early stages of the engine development process using experimental modal analysis (EMA) & the robust design of each engine functional system. In addition, the engine structural attenuation (SA) is enhanced such that the radiated combustion noise of the engine can be maintained at a target level even with an increased combustion excitation. It was found that the engine system has better parts and worse parts in frequency range throughout the SA analysis. It is important that weak points in the system should be optimized.
2011-05-17
Journal Article
2011-01-1562
Tamer Elnady, Sara Elsaadany, D. W. Herrin
Diesel engines produce harmful exhaust emissions and high exhaust noise levels. One way of mitigating both exhaust emissions and noise is via the use of after treatment devices such as Catalytic Converters (CC), Selective Catalytic Reducers (SCR), Diesel Oxidation Catalysts (DOC), and Diesel Particulate Filters (DPF). The objective of this investigation is to characterize and simulate the acoustic performance of different types of filters so that maximum benefit can be achieved. A number of after treatment device configurations for trucks were selected and measured. A measurement campaign was conducted to characterize the two-port transfer matrix of these devices. The simulation was performed using the two-port theory where the two-port models are limited to the plane wave range in the filter cavity.
2011-05-17
Technical Paper
2011-01-1571
Myung-Gyu Kim
The expectation of customers on ride comfort is very high and vehicle engineers also have keen interesting to improve ride vibration and road noise. As the conventional tuning parameters for the ride vibration and road noise, vibration characteristics of tire, body structure, bushing, suspension members etc. are mainly considered. But these conventional tuning parameters are sometimes not enough due to the side effects such like handling performances and durability. Therefore, instead of these conventional design and tuning parameters, suspension geometry and alignment characteristics of suspension system are selected as the alternative parameters to compromise ride vibration, road noise and vehicle dynamic performance. In this research, multi-link type rear suspension is selected for the integrated analysis of ride vibration, road impact noise and handling performance.
2011-05-17
Journal Article
2011-01-1568
Christian Fernholz, Ronald Perri, David Watts, David Willmer, Jeff Williams
This paper discusses the optimization of an automotive hydraulic steering pump pulley design for improved in-vehicle pump NVH performance. Levels of steering pump whine noise heard inside a vehicle were deemed objectionable. Vehicle and component transfer path analyses indicated that the dominant noise path for the whine noise was airborne in nature. Subsequent experimental modal analysis indicated that the steering pump pulley was a major contributor to the amount of radiated noise produced by the pump/pulley system. CAE analysis was used to further analyze the dynamic behavior of the pulley and develop an optimized design with decreased noise radiation efficiency. The results predicted with the CAE analysis were verified in-vehicle, resulting in a vehicle with acceptable steering pump whine noise performance.
2011-05-17
Technical Paper
2011-01-1566
Thomas Reinhart, Mitchel Smolik
Several new or significantly upgraded heavy duty truck engines are being introduced in the North American market. One important aspect of these new or revised engines is their noise characteristics. This paper describes the noise related characteristics of the new DD15 engine, and compares them to other competitive heavy truck engines. DD15 engine features relevant to noise include a rear gear train, isolated oil pan and valve cover, and an amplified high pressure common rail fuel system. The transition between non-amplified and amplified common rail operation is shown to have a significant noise impact, not unlike the transition between pilot injection and single shot injection in some other engines.
2011-05-17
Technical Paper
2011-01-1576
Stefan Bernsteiner, Daniel Wallner
Experimental researches on brake squeal have been performed since many years in order to get an insight into friction-excited vibrations and squeal triggering mechanisms. There are many different possibilities to analyse brake squeal. The different operating deflection shapes can be detected using e.g. laser vibrometer systems or acceleration sensors. Piezoelectric load cells can be used for the measurement of the normal contact force of the brake pad. The presented test setup measures not only the mean value of the friction force between brake pad and disc at a certain brake pressure, but also the superposed vibration of this force, which only occurs during a squeal event. Therefore the guide pins of the brake caliper are replaced by modified ones. The brake pads are held in position by these pins and the resulting force of the brake torque, hence the friction force, acts on these pins. The shape of the pins is optimized for measuring these forces.
2011-05-17
Journal Article
2011-01-1575
John David Fieldhouse, David Bryant, Chris John Talbot
Thermo-elastic and thermo-plastic behaviour takes place with a disc brake during heavy braking and it is this aspect of braking that this paper considers. The work is concerned with working towards developing design advice that provides uniform heating of the disc, and equally important, even dissipation of heat from the disc blade. The material presented emanates from a combination of modeling, on-vehicle testing but mainly laboratory observations and subsequent investigations. The experimental work makes use of a purpose built high speed brake dynamometer which incorporates the full vehicle suspension for controlled simulation of the brake and vehicle operating conditions. Advanced instrumentation allows dynamic measurement of brake pressure fluctuations, disc surface temperature and discrete vibration measurements.
2011-05-17
Technical Paper
2011-01-1574
Eric Denys
The development and validation of a brake pad insulator damping measurement procedure by the SAE Brake NVH Standards Committee was presented at the 2010 SAE Brake Colloquium (Paper 2010-01-1685). In Europe, in 2010, the EKB Working Group identified the need to develop a similar procedure, and started some activities which lead to the release of a standard similar but different than the SAE J3001. The SAE and EKB working groups agreed that having a global standard was of paramount importance, so the 2 groups decided to meet in November of 2010 to flush out the details of the J3001 global procedure. The details of the new test procedure, test setup and recommendation for proper test practices are described in this paper. This description provides an excellent foundation for evaluating the insulator damping properties over a range of temperatures and frequencies.
2011-05-17
Technical Paper
2011-01-1581
Z. C. Feng, Perry Gu
Tire cavity noise refers to the vehicle noise due to the excitation of the acoustic modes of a tire air cavity. Although two lowest acoustic modes are found to be sufficient to characterize the cavity dynamics, the dynamical response of these two modes is complicated by two major factors. First, the tire cavity geometry is affected by the static load applied to the tire due to vehicle weight. Second, the excitation force from the tire-road contact changes position as the tire rotates. In this paper, we first develop dynamic equations for the lowest cavity modes of a rotating tire under the static load. Based on the model, we obtain the forces transmitted to the wheel from the tire resulting from the random contact force between the tire and the road surface. The transmitted forces along the fore/aft direction and the vertical direction show two peaks at frequencies that are dependent both on the tire static load and on the vehicle speed.
2011-05-17
Technical Paper
2011-01-1579
Takashi Nakae, Takahiro Ryu, Atsuo Sueoka
This paper deals with low-frequency squeal phenomena generated in floating type of car disc brake units. First, the vibration characteristics of low-frequency squeal (about 2 kHz) were investigated. Here, in order to reproduce the squeal, a bench-test apparatus consisting of an actual automotive disc brake unit was utilized, itself comprising a disc, pad, and caliper. With this, the associated frequency characteristics were experimentally determined. It was found that the squeal is caused by coupled out-of-plane vibration modes among the disc and caliper due to Coulomb friction. As an experimental countermeasure, a dynamic absorber was applied to the leading side or the trailing side of the inner caliper. It was found that squeal can be suppressed when the natural frequency of the dynamic absorber is tuned so as to be near the frequency of the squeal, and that squeal can be suppressed even without viscous damping of the dynamic absorber.
2011-05-17
Technical Paper
2011-01-1580
Mohamad S. Qatu, Roger King, Omar Shubailat, Rachel Wheeler
Variability in design (e.g. tolerance), material, manufacturing, or other sources of variation causes significant variation in vehicle noise, vibration and harshness (NVH) response. This leads to a higher percentage of produced vehicles with higher levels of NVH leading to higher number of warranty claims and loss of customer satisfaction, which are proven costly to the original equipment manufacturers (OEM). Measures must be taken to insure less warranty claims and higher levels of customer satisfaction. As a result, original equipment manufacturers have implemented design for variation in the design process to secure an acceptable (or within specification) response. We will focus on some aspects of design variations in a tire/wheel assembly that should be considered in the design process. In particular, certain materials (e.g. rubber) are known to have variation in stiffness that is either unavoidable or proven costly if tighter control is desired.
2011-05-17
Technical Paper
2011-01-1584
Christian M. Fernholz
The present work discusses an objective test and analysis method developed to quickly quantify steering gear rattle noise heard in a vehicle. Utilizing envelope analysis on the time history data of the rattle signal, the resulting method is simple, fast, practical and yields a single-valued metric which correlates well to subjective measures of rattle noise. In contrast to many other rattle analysis methods, the approach discussed here is completed in the time domain. As applied to rattle noise produced by automotive electric steering systems, the metric produced with this analysis method correlates well with subjective appraisals of vehicle-level rattle noise performance. Lastly, this method can also be extended to rattle measurements at the component and subcomponent level.
2011-05-17
Technical Paper
2011-01-1577
John David Fieldhouse, David Bryant, Chris John Talbot
The paper overviews the modes of vibration of the principal component parts of a brake and their contribution to system instability during noise generation. It is shown that both in-plane and out-of-plane vibration are present and that both can be related to the vibration of the pad. It is further shown that the pad and its region often provide a solution or “fix” towards noise prevention and it is this area that forms the focus of this investigation. The collective evidence, proposals and associated theory are applied to real brake case studies when it is demonstrated that disc/pad interface “spragging” may be the source of brake noise. Measurements of the position of the dynamic centre of pressure (CoP) support the theoretical predictions that a leading CoP induces brake noise. Design proposals are suggested that may be applied early in the design phase as a means to reduce the propensity of a brake to generate noise.
2011-05-17
Journal Article
2011-01-1582
Paul R. Donavan, Alan Parrett, Dave Nielubowicz, Jinshuo Zhu
Developing common methods of noise evaluation and facilities can present a number of challenges in the area of tire/pavement noise. Some of the issues involved include the design and construction of pavements globally, the change in pavement over time, and variation in the noise produced with standard test tires used as references. To help understand and address these issues for airborne tire/pavement noise, acoustic intensity measurement methods based on the On-board Sound Intensity (OBSI) technique have been used. Initial evaluations have included measurements conducted at several different proving grounds. Also included were measurements taken on a 3m diameter tire noise dynamometer with surfaces replicating test track pavements. Variation between facilities appears to be a function of both design/construction and pavement age. Consistent with trends in the literature, for smooth asphalt surfaces, the newest surface produced levels lower than older surfaces.
2011-05-17
Technical Paper
2011-01-1591
Kumbhar S. Mansinh, Atul Miskin, Vishal Vasantrao Chaudhari, Ashish Rajput
The noise and vibration performance of diesel fueled automotives is critical for overall customer comfort. The stationary vehicle with engine running idle (Vehicle Idle) is a very common operating condition in city driving cycle. Hence it is most common comfort assessment criteria for diesel vehicles. Simulations and optimization of it in an early stage of product development cycle is priority for all OEMs. In vehicle idle condition, powertrain is the only major source of Noise and Vibrations. The key to First Time Right Idle NVH simulations and optimization remains being able to optimize all Transfer paths, from powertrain mounts to Driver Ear. This Paper talks about the approach established for simulations and optimization of powertrain forces entering in to frame by optimizing powertrain mount hard points and stiffness. Powertrain forces optimized through set process are further used to predict the vehicle passenger compartment noise and steering vibrations.
2011-05-17
Technical Paper
2011-01-1600
Theo Geluk, Peter Van der Linden, Davide Vige', Massimo Caudano, Simone Gottardi, Fabio Ciraolo, Hamid Mir
Road-tire induced vibrations are in many vehicles determining the interior noise levels in (semi-) constant speed driving. The understanding of the noise contributions of different connections of the suspension systems to the vehicle is essential in improvement of the isolation capabilities of the suspension- and body-structure. To identify these noise contributions, both the forces acting at the suspension-to-body connections points and the vibro-acoustic transfers from the connection points to the interior microphones are required. In this paper different approaches to identify the forces are compared for their applicability to road noise analysis. First step for the force identification is the full vehicle operational measurement in which target responses (interior noise) and indicator responses (accelerations or other) are measured.
2011-05-17
Journal Article
2011-01-1527
Rick Dehner, Ahmet Selamet, Philip Keller, Michael Becker
The unsteady surge behavior of a turbocharger compression system is studied computationally by employing a one-dimensional engine simulation code. The system modeled represents a new turbocharger test stand consisting of a compressor inlet duct breathing from ambient, a centrifugal compressor, an exit duct connected to an adjustable-volume plenum, followed by another duct which incorporates a control valve and an orifice flow meter before exhausting to ambient. Characteristics of mild and deep surge are captured as the mass flow rate is reduced below the stability limit, including discrete sound peaks at low frequencies along with their amplitudes in the compressor (downstream) duct and plenum. The predictions are then compared with the experimental results obtained from the cold stand placed in a hemi-anechoic room.
2011-05-17
Technical Paper
2011-01-1530
Uday Senapati, Graham Evans, Aaron Hankinson
The drive for lower CO₂ emissions places ever greater demand on cooling dissipation for a multi-cylinder internal combustion engine. This challenge has increased the requirements of the engine cooling system, particularly in countries where high ambient temperatures prevail and HVAC usage is high. Environmental necessity coupled with market demands have resulted in cars which emit a higher level of cooling fan noise which is intrusive in an urban environment and objectionable to customers. Conventional quantification of noise using traditional units and metrics was found to be insufficient for effective Sound Quality analysis. To assist Bentley Motors, a high performance luxury vehicle manufacturer, with its brand cachet and its commitment to the environment and customer, a new sound metric analysis has been devised to help the business deliver an ever-quieter exterior power unit cooling system.
2011-05-17
Technical Paper
2011-01-1532
Charlie Teng, Fumin Pan, Jemai Missaoui, Scott Deraad
Turbocharged gasoline engines are typically equipped with a compressor anti-surge valve or CBV (compressor by-pass valve). The purpose of this valve is to release pressurized air between the throttle and the compressor outlet during tip-out maneuvers. At normal operating conditions, the CBV is closed. There are two major CBV mounting configurations. One is to mount the CBV on the AIS system. The other is to mount the CBV directly on the compressor housing, which is called an integrated CBV. For an integrated CBV, at normal operating conditions, it is closed and the enclosed passageway between high pressure side and low pressure side forms a “side-branch” in the compressor inlet side (Figure 12). The cavity modes associated with this “side-branch” could be excited by shear layer flow and result in narrow band flow noises.
2011-05-17
Technical Paper
2011-01-1536
Mohammad Kazem Baghi Abadi, Ali Hajnayeb, Ali Hosseingholizadeh, Ahmad Ghasemloonia
This paper presents an algorithm for the detection of single and multiple misfires in internal combustion engines, using only the signal of the knock sensor. Several experiments were conducted on a four-cylinder engine to obtain the necessary signals in the healthy and faulty conditions. The faulty conditions were created by disconnecting the wires of the spark-plugs. The signal of the knock sensor is analyzed and the time-domain signals of different orders of engine vibrations are extracted using a Vold-Kalman filter (VKF). A set of statistical features were then extracted from the time-domain signals of each order. These features are representative of the engine condition. In the next step, the computed features were plotted for different states and are analyzed. Consequently, a criterion for identifying the engine misfire is obtained based on the extracted features.
2011-05-17
Technical Paper
2011-01-1535
Christopher Edward Baker, Homer Rahnejat, Ramin Rahmani PhD, Stephanos Theodossiades
Piston compression rings are thin, incomplete circular structures which are subject to complex motions during a typical 4-stroke internal combustion engine cycle. Ring dynamics comprises its inertial motion relative to the piston, within the confine of its seating groove. There are also elastodynamic modes, such as the ring in-plane motions. A number of modes can be excited, dependent on the net applied force. The latter includes the ring tension and cylinder pressure loading, both of which act outwards on the ring and conform it to the cylinder bore. There is also the radial inward force as the result of ring-bore conjunctional pressure (i.e. contact force). Under transient conditions, the inward and outward forces do not equilibrate, resulting in the small inertial radial motion of the ring.
2011-05-17
Technical Paper
2011-01-1545
Chi La, Marco Poggi, Patrick Murphy, Ondrej Zitko
In response to environmental and fossil fuel usage concerns, the automotive industry will gradually move from Hybrid Electric Vehicles (HEV) which includes a shift of internal combustion engines toward Zero Emissions Vehicles (ZEV). Refinement is an important aspect in the successful adoption of any new technology and ZEV brings its own NVH challenges owing to the unique dynamic characteristics of the powertrain and driveline system. This paper presents considerations for addressing dynamic driveline NVH issues that are common to 100% electric vehicles; issues that manifest themselves as groans, rattles and clunks. A dynamic torsional analytical model of the powertrain & driveline will be presented. The analytical model served as the baseline for an extensive parametric study using the Genetic Algorithm (GA) technique, whereby the effectiveness of practical countermeasures was investigated.
2011-05-17
Journal Article
2011-01-1550
Wei Sun, Yinong Li, Jingying Huang
Dual Mass Flywheel (DMF) has better damping capacity than the conventional Clutch Torsional Damper (CTD), and is more suitable for diesel engine, Dual Clutch Transmission (DCT) and hybrid vehicles. Dual Mass Flywheel-Radial Spring (DMF-RS) is a DMF that has a specific structure. In the light of working principal and static analysis, the hard nonlinear torsional stiffness of DMF-RS is derived in this paper, which is very important to a driveline damper. On this basis, a simulation model is developed to analyze the dynamic response of DMF and CTD excited by idle engine; the comparison of the two dampers reveals that the DMF has better damping capacity, high-frequency filter ability and can reduce crankshaft load.
2011-05-17
Technical Paper
2011-01-1559
X. Hua, J. Liu, D. W. Herrin, T. Elnady
This paper documents a finite element approach to predict the attenuation of muffler and silencer systems that incorporate diesel particulate filters (DPF). Two finite element models were developed. The first is a micro FEM model, where a subset of channels is modeled and transmission matrices are determined in a manner consistent with prior published work by Allam and Åbom. Flow effects are considered at the inlet and outlet to the DPF as well as viscous effects in the channels themselves. The results are then used in a macro FEM model of the exhaust system where the transmission relationship from the micro-model is used to simulate the DPF. The modeling approach was validated experimentally on an example in which the plane wave cutoff frequency was exceeded in the chambers upstream and downstream to the DPF.
2011-05-17
Technical Paper
2011-01-1560
Giancarlo Chiatti, Erasmo Recco, Ornella Chiavola
The optimization of the combustion process in diesel engines is one of the challenges to improve performance, emissions, fuel consumption and NVH characteristics. This work constitutes one of the last steps of a comprehensive research program in which vibration sensors are used with the purpose of developing and setting up a methodology that is able to monitor and optimize the combustion process by means of non-intrusive measurements. Previously published results have demonstrated the direct relationship that exists between in-cylinder pressure and engine block vibration signals, as well as the sensitivity of the engine surface vibration to variation of injection parameters when the accelerometer is placed in a sensitive location of the engine block.
Viewing 1 to 30 of 52570

Filter

  • Range:
    to:
  • Year: