Criteria

Text:
Display:

Results

Viewing 1 to 30 of 46025
2011-05-17
Technical Paper
2011-01-1621
Frank Friedrich
While the microcellular urethane is widely known in the automotive industry for its use in jounce bumpers, its use in Noise Vibration Harshness (NVH) applications is often not as well recognized. Even though there are some NVH parts in the market, rubber still dominates it. The objective of this paper is to demonstrate the material properties of MCU and their relevance for NVH applications in chassis and suspension components. It will also demonstrate the importance of package design to suit the use of the MCU material. This is especially important to not only achieve the best performance but also keep overall cost and weight under control. Several application types will be introduced with general design suggestions. A detailed design guideline for these applications is not part of this paper. Each application has a large variety of parameters to be considered in the design. They need to be selectively applied based on customer performance targets.
2011-05-17
Technical Paper
2011-01-1623
Alan V. Parrett, Chong Wang, Xiandi Zeng, David Nielubowicz, Mark Snowden, Jonathon H. Alexander, Ronald Gerdes, Bill Leeder, Charles Zupan
In recent years several variants of lightweight multi-layered acoustic treatments have been used successfully in vehicles to replace conventional barrier-decoupler interior dash mats. The principle involved is to utilize increased acoustic absorption to offset the decrease in insertion loss from the reduced mass such that equivalent vehicle level performance can be achieved. Typical dual density fibrous constructions consist of a relatively dense cap layer on top of a lofted layer. The density and flow resistivity of these layers are tuned to optimize a balance of insertion loss and absorption performance. Generally these have been found to be very effective with the exception of dash mats with very high insertion loss requirements. This paper describes an alternative treatment which consists of a micro-perforated film top layer and fibrous decoupler layer.
2011-05-17
Technical Paper
2011-01-1628
Hejie Lin, Turgay Bengisu, Zissimos Mourelatos
Styrene-Butadiene Rubber (SBR), a copolymer of butadiene and styrene, is widely used in the automotive industry due to its high durability and resistance to abrasion, oils and oxidation. Some of the common applications include tires, vibration isolators, and gaskets, among others. This paper characterizes the dynamic behavior of SBR and discusses the suitability of a visco-elastic model of elastomers, known as the Kelvin model, from a mathematical and physical point of view. An optimization algorithm is used to estimate the parameters of the Kelvin model. The resulting model was shown to produce reasonable approximations of measured dynamic stiffness. The model was also used to calculate the self heating of the elastomer due to energy dissipation by the viscous damping components in the model. Developing such a predictive capability is essential in understanding the dynamic behavior of elastomers considering that their dynamic stiffness can in general depend on temperature.
2011-05-17
Technical Paper
2011-01-1629
Saurabh Suresh, Jeff Kastner, Teik Lim
Reduction of noise transmitted through laminated glass with interlayer is of interest to vehicle applications. Altering the structure of the interlayer can impact sound transmission loss particularly at the coincidence frequency. This study investigates the feasibility of including a porous layer within the laminated glass to act as an acoustic damper. To understand the underlying physics controlling transmission loss in laminated glass design, an approach utilizing transfer matrices is used for modeling each layer in the laminated glass. These transfer matrices are used to relate the acoustic characteristics of two points within a layer. For any two layers in contact, an interface matrix is defined that relates the acoustic fields of the layers depending on their individual characteristics. The solid layer is modeled as an elastic element and the sound propagation through the porous materials is described using the Biot theory.
2011-05-17
Technical Paper
2011-01-1632
Ion Pelinescu, Andrew Christie
One of the most effective NVH solutions used in the automotive industry to reduce structure-borne noise is to apply vibration damping treatments to the vehicle structure. These damping treatments need to meet increasing weight reduction targets, while offering the same or better damping properties. While Liquid Applied Structural Dampers (LASD) are now delivering high damping performance at lower densities, traditional damping measuring techniques are falling short in describing the performance of these extensional layers when applied onto more realistic test samples or real structures. This paper discusses the damping performance of LASD technology, in particular the newer generations of acrylic-based waterborne LASD materials, which through improvements in polymer architecture are achieving increased damping efficiencies together with reduced density.
2011-05-17
Technical Paper
2011-01-1624
Prasanth B, Sachin Wagh, David Hudson
Baffle plates with heat reactive expandable foam sealants have increasingly found their applications in automotives. They are used to separate body cavities and to impede noise, water and dust propagation inside of body cavities, thus control noise intrusion into the passenger compartment. Use of these sealant materials has grown significantly as the demands to improve vehicle acoustic performance has increased. Traditionally quantification of the acoustic performance of expandable baffle samples involved making separate vehicles with and without expandable baffles and measure the incab noise to know the effect. The absolute acoustic evaluation of the baffles is very difficult as number of other vehicle parameters is also responsible for vehicle incab noise. Also, it is a time consuming and a costly method to evaluate.
2011-05-17
Technical Paper
2011-01-1625
John G. Cherng, Qian Xi, Pravansu Mohanty, Gordon Ebbitt
Acoustical materials are widely used in automotive vehicles and other industrial applications. Two important parameters namely Sound Transmission Loss (STL) and absorption coefficient are commonly used to evaluate the acoustical performance of these materials. Other parameters, such as insertion loss, noise reduction, and loss factors are also used to judge their performance depending on the application of these materials. A systematic comparative study of STL and absorption coefficient was conducted on various porous acoustical materials. Several dozen materials including needled cotton fiber (shoddy) and foam materials with or without barrier/scrim were investigated. The results of STL and absorption coefficient are presented and compared. As expected, it was found that most of materials are either good in STL or good in absorption. However, some combinations can achieve a balance of performance in both categories.
2011-05-17
Technical Paper
2011-01-1626
Jonathan Alexander, David Reed, Ronald Gerdes
Flat, constant thickness composites that consisted of a microperforated top layer plus a fibrous decoupler layer were tested for random absorption and transmission loss (TL) performance. The top, microperforated layer consisted of a relatively thick film that contained small, precise micro-perforations. For reference, top layers that consisted of a resistive scrim and an impervious film were also included in this study. Two fibrous materials of constant thickness were used for the decoupler layer between a steel panel and the top microperforated film. The composites' absorption and TL performance were also modeled using the well-known transfer matrix method. This method has been implemented in a commercially available statistical energy analysis (SEA) software package. A comparison of testing and modeling results showed reasonable agreement for absorption results and even better agreement for transmission loss and insertion loss results.
2011-05-17
Journal Article
2011-01-1627
J. Liu, D. W. Herrin
Microperforated panel (MPP) absorbers are rugged, non-combustible, and do not deteriorate over time. That being the case, they are especially suitable for long term use in harsh environments. However, the acoustic performance is modified when contaminated by dust, dirt, or fluids (i.e. oil, water). This paper examines that effect experimentally and correlates the absorption performance with Maa's theory for micro-perforated panels. Transfer impedance and absorption coefficient are measured for different levels of aluminum oxide and carbon dust accumulation. The amount of dust contamination is quantified by measuring the luminance difference between clean and dirty panels with a light meter. The porosity and hole diameter in Maa's equation are modified to account for dust obstruction. The effect of coating the MPP with oil, water, and other appropriate viscous fluids was also measured. This effect was simulated by modifying the viscous factor in Maa's equation.
2011-05-17
Technical Paper
2011-01-1634
Michael Dinsmore, Richard Bliton, Scott Perz
Using advanced, multi-layer poro-elastic acoustical material modeling technologies, an example of acoustical performance optimization of an underhood sound absorber application is presented. In this case, a porous facing in combination with a fibrous sound absorber pad is optimized for maximum efficiency, which allows for dramatic reduction in pad density and weight. Overall sound absorption performance is shown to be equal or improved versus frequency relative to the incumbent design.
2011-05-17
Technical Paper
2011-01-1637
Ahad Khezerloo, Amin owhadi Esfahani PhD, Sina Jalily lng
One of important problems in railway transportation systems is control of noise and vibration. Metal foams are very good medias for absorbing noise. So in this paper, noise of motion of a train is simulated by MATLAB software and the reduction of noise level in a compartment of passenger car that is equipped by metal foam sheets is considered. Commonly, the sound absorption coefficients are obtained experimentally and they are available in datasheets and references. The different parameters that influence on the capability of this equipment were considered. For example the microstructure, thickness, magnitude of compaction, relative density and etc of metal foam is effective parameters. High porosity has good effect on the performance of absorber sheet. By increasing of compaction ratio, in frequency domain we will have enhancing of absorption of the noise. Compaction process is done by two different ways: one is direct and else is progressively.
2011-05-17
Journal Article
2011-01-1575
John David Fieldhouse, David Bryant, Chris John Talbot
Thermo-elastic and thermo-plastic behaviour takes place with a disc brake during heavy braking and it is this aspect of braking that this paper considers. The work is concerned with working towards developing design advice that provides uniform heating of the disc, and equally important, even dissipation of heat from the disc blade. The material presented emanates from a combination of modeling, on-vehicle testing but mainly laboratory observations and subsequent investigations. The experimental work makes use of a purpose built high speed brake dynamometer which incorporates the full vehicle suspension for controlled simulation of the brake and vehicle operating conditions. Advanced instrumentation allows dynamic measurement of brake pressure fluctuations, disc surface temperature and discrete vibration measurements.
2011-04-12
Technical Paper
2011-01-1397
Vladimir Marcov, Sergey Gladyshev, Sergey Devianin
Parameters of the fuel economy and the exhaust gases pollution of the high-speed diesel engines, with unshared and half-shared combustion chambers, are predetermined by processes of fuel spray and fuel-air mixture creation. The parameters of these processes (fuel spraying and development of flame structure dynamic) appreciably depend from design features of a flowing part of the injector tips. The major parameters of the injector tips design are the spraying nozzles length and the ratio of the length these nozzles to their diameters. The experimental research of the D-245.12C type diesel engine has been carried out. Fuel injectors of the diesel engine were equipped with injector tips of different spray nozzles lengths. The experimental data show improvement fuel efficiency, reduction of emissions and smoke due to optimization of geometries in the injector tip.
2011-04-12
Journal Article
2011-01-1401
Yoolkoo Kim, Hyundal Park, Jeong Uk An, Tae-Suek Kan, Joonsung Park
Various polymer-based coatings are applied on piston skirt to reduce friction loss between the piston skirt and cylinder bore which is one of main factors of energy loss in an automotive engine system. These coatings generally consist of polymer binder (PAI) and solid lubricants (graphite or MoS₂) for low friction property. On the other hand, the present study found that PTFE as a solid lubricant and nano diamond as hard particles can be used to improve the low friction and wear resistance simultaneously. In the process of producing coating material, diamond particles pulverized to a nano size tend to agglomerate. To prevent this, silane (silicon coupling agent) treatment was applied. The inorganic functional groups of silane are attached to the nano diamond surface, which keep the diamond particles are apart.
2011-05-17
Technical Paper
2011-01-1724
Juliette Florentin, Francois Durieux, Yukihisa Kuriyama, Toyoki Yamamoto
The present work attempts a complete noise and vibration analysis for an electric vehicle at concept stage. The candidate vehicle is the Future Steel Vehicle (FSV), a lightweight steel body with an electric motor developed by WorldAutoSteel [1,2,3]. Measurements were conducted on two small Mitsubishi vehicles that both share the same body, yet one is equipped with an internal combustion engine and the other with an electric motor. The outcome was used as a starting point to identify assets and pitfalls of electric motor noise and draw a set of Noise Vibration and Harshness (NVH) targets for FSV. Compared to a combustion engine, the electric motor shows significantly lower sound pressure levels, except for an isolated high frequency peak heard at high speeds (3500 Hz when the vehicle drives at top speed). The prominence of this peak is lowered by increased use of acoustic absorbent materials in the motor compartment.
2011-08-30
Technical Paper
2011-01-1763
Kevin Cedrone, Wai K. Cheng, Samir Chahine, John Williams, Brad VanDerWege
The fuel effects on HCCI operation in a spark assisted direct injection gasoline engine are assessed. The low load limit has been extended with a pilot fuel injection during the negative valve overlap (NVO) period. The fuel matrix consists of hydrocarbon fuels and various ethanol blends and a butanol blend, plus fuels with added ignition improvers. The hydrocarbon fuels and the butanol blend do not significantly alter the high or the low limits of operation. The HCCI operation appears to be controlled more by the thermal environment than by the fuel properties. For E85, the engine behavior depends on the extent that the heat release from the pilot injected fuel in the NVO period compensates for the evaporative cooling of the fuel.
2011-08-30
Technical Paper
2011-01-1769
Robert Kiplimo, Eiji Tomita, Nobuyuki Kawahara, Shiyu Zhou, Sumito Yokobe
Effects of injection parameters on combustion and emission characteristics of diesel PCCI engine operating on optical and test engine was investigated. PCCI combustion was achieved through slightly narrow included angle injector, low compression ratio coupled with exhaust gas recirculation. Analysis based on diesel spray evolution, combustion process visualization and analysis was carried out. Spray penetration was evaluated and related to the exhaust emissions. Advancing the injection timing and EGR extended the ignition delay, decreased NOx emissions and increased HC, smoke and CO emissions. Higher injection pressure led to low emissions of NOx, smoke, HC and comparable CO. Optimum spray targeting position for minimum emission was identified. Impingement on the piston surface led to deterioration of emissions and increased fuel consumption while spray targeting the upper edge of Derby hat wall showed improvement in emission and engine performance.
2011-08-30
Technical Paper
2011-01-1768
Yoshimitsu Kobashi, Daijiro Tanaka, Teppei Maruko, Satoshi Kato, Masato Kishiura, Jiro Senda
A dual fuel operation with different reactivity fuels has the possibility of optimizing performance and emissions in premixed charge compression ignition engines by controlling the spatial concentration and distribution of both fuels. In the present study, n-heptane and i-octane were independently injected through two different injectors. In-cylinder pressure analysis and emissions measurement were performed in a compression ignition engine. Injection timings, fuel quantity ratio between the injections were changed for the two cases, in which one fuel was injected using a port fuel injection system while the other was directly injected into the cylinder, in order to drastically vary mixture distributions and ignition timings. In addition, an optical diagnostic was performed in a rapid compression and expansion machine to develop an understanding of the ignition processes of the two mixtures.
2011-05-17
Journal Article
2011-01-1693
Luca Guj, Theophane Courtois, Claudio Bertolini
Typically, in the automotive industry, the design of the body damping treatment package with respect to NVH targets is carried out in such a way to achieve panel mobility targets, within given weight and cost constraints. Vibration mobility reduction can be efficiently achieved thanks to dedicated CAE FE tools, which can take into account the properties of damping composites, and also, which can provide their optimal location on the body structure, for a minimal added mass and a maximized efficiency. This need has led to the development of different numerical design and optimization strategies, all based on the modeling of the damping composites by mean of equivalent shell representations, which is a versatile solution for the full vehicle simulation with various damping layouts.
2011-08-30
Technical Paper
2011-01-2095
Georg Huthwohl, Sascha Dolenec
SCR technology is becoming more and more important for the segment of diesel-driven passenger cars. Due to space and functional demands the dependency of SCR performance on a uniform supply of ammonia into the catalytic substrates is highly increased. Both an even distribution of the AdBlue® spray and a completed evaporation and decomposition of the droplets are the key to achieve the desired ammonia spread. Evaluation of the influence of spray quality on the AdBlue® decomposition and catalyst performance are leading to a new approach in dosing, using a special nozzle and air-supply strategy. The resulting new technology is evaluated and compared to the state of the art.
2011-08-30
Journal Article
2011-01-2111
Nobuo Ushioda, Yasuhiro Ogasawara
Fuel economy is one of the most essential performance requirements for Passenger Car Motor Oil because of fuel economy regulations in many countries and increasing fuel prices. The ILSAC GF-5 specification was issued on December 22, 2009 and requires better fuel economy performance based on the Sequence VID (Seq. VID) Test and higher weighted piston deposit merits based on the Sequence IIIG Test, compared to the ILSAC GF-4 specification. Fuel economy performance is affected by viscosity, friction modification and the lubricant additive chemistries. However, fuel economy engine tests under combustion mode introduce high variability into a fuel economy measurement. Screening by bench testing is complicated by the difficulty to reproduce friction conditions of all of engine parts. A motored friction torque test using an engine is one of the better solutions for fuel economy screening.
2011-08-30
Technical Paper
2011-01-2113
Masataka Hashimoto, Tadanori Azuma, Morio Sumimoto, Kanji Mitsuda
A new type of lube oil cleaning system is successfully developed for semi-permanent use of oil by always keeping oil clean with the result of no oil change and no waste oil. It is in practical use in many marine diesel engines and in some other fields. In recent years, possibility of semi-permanent use of engines themselves has been expected based on the field data. A ship test for 7 years has verified the expected semi-permanent use of engines with almost no wear and constant thermal efficiency during the test. We present the characteristics of the oil cleaning system and the result of the test. Also, a new type of fuel oil cleaning system is presented which is useful for cleaning low quality fuel oil. As a whole, this test is the beginning of the new stage of our work following the semi-permanent use of lube oil, which has been verified and established in many diesel engines since the 1980s.
2011-08-30
Journal Article
2011-01-2114
Jai G. Bansal, Patrick Colby, Maryann Devine, Jack Emert, Kaustav Sinha
This paper is first in a series of papers designed to investigate wear processes in modern heavy duty diesel engines. The objective of the series is to discuss the effects that engine drive cycle, lubricant formulations and in-service ageing of lubricants have on wear of critical engine components. In this paper, the Radioactive Tracer Technology technique was used to study the steady state wear behavior of a number of contacting surfaces in a Caterpillar 1P engine, as a function of the drive cycle. A test protocol consisting of 7 modes or stages was used to simulate a variety of drive cycles. The results from this work provide useful insights into the wear behavior of these surfaces under a variety of speed and load conditions.
2011-08-30
Technical Paper
2011-01-2110
Farzan Parsinejad, Wilton Biggs
The delicate balance between global supply and demand for energy, in conjunction with environmental concerns related to burning fossil fuels, have resulted in vehicle designs that stress higher fuel economy. Among new engine designs is Direct Injection Spark Ignition, or DISI, which employs a more precise fuel metering system and is designed for combustion at higher compression ratios than Port Fuel Injection (PFI) engines. As a result, the performance of DISI engines can easily be altered by the presence of carbonaceous deposits on intake valves and in the combustion chamber. In this study, the characteristics of these deposits have been investigated using elemental and thermal analytical techniques. Deposits from intake valves and combustion chambers have been collected from various DISI engines (both older and more modern ones).
2011-08-30
Technical Paper
2011-01-2030
Takuji Murayama
The continuously variable transmission (CVT) with a rubber belt used in scooters is also regarded as a potential automatic transmission mechanism for conventional motorcycles. By making this system more compact and building it into the engine, a motorcycle CVT engine has been developed that is about the same size as a manual transmission (MT) engine. During driving with a CVT, heat is generated by friction at the sheaves, and therefore it was necessary to secure a certain length of belt to ensure that external air flows efficiently to the sheaves. However, making the CVT more compact restricted the belt length, which decreased cooling performance and increased the number of bends in the belt, making it difficult to maintain durability. To address this issue, a plastic resin drive belt and newly designed sheaves were adopted, and durability of more than that of a scooter was achieved.
2011-08-30
Journal Article
2011-01-2029
Atsushi Tanaka, Hiroki Shimada, Naoki Hiraiwa, Tsuyoshi Arai, Hideki Asano, Yasuhiro Nishikawa
The need to improve fuel consumption by saving the weights of automobile parts is growing from the viewpoint of global warming mitigation. In the case of a throttle body for controlling the air flow volume into an engine, it is important to achieve a high dimensional accuracy of the valve-bore gap in the state of closed valve. In fact, most throttle bodies are made of precision-machined metal. Therefore, resin throttle bodies are drawing attention as a lightweight alternate. However, in comparison with metal throttle bodies, resin throttle bodies have two potential disadvantages that should be solved prior to productization. The first one is greater air leakage in the state of closed valve, and the second one is smaller heat conduction for unfreezing the valve in a frigid climate. We have developed an electronic resin throttle body that has overcome the above-mentioned disadvantages.
2011-08-30
Technical Paper
2011-01-2052
Rei Ishida, Tomohiro Nakayama, Makoto Kaneko, Koji Morikawa
This paper details the air-fuel mixing process in a gasoline direct injection (DI) engine. Laser measurement techniques such as particle image velocimetry (PIV) and laser induced fluorescence (LIF) were employed on the optical engine with a transparent cylinder to analyze the in-cylinder flow and fuel vapor concentration. In addition, firing tests were conducted using an actual engine. Test results showed that the multi-stage injection is effective for air-fuel mixing and improvement of combustion stability.
2011-08-30
Technical Paper
2011-01-2046
Jean-Guillaume Nerva, Teruo Yamaguchi, Hiroki Iguma, Hiroki Nishigai, Katsufumi Kondo, Satoshi Takano, Tetsuya Aizawa, Caroline L. Genzale, Lyle M. Pickett
For better understanding of soot formation and oxidation processes in a biodiesel spray flame, the morphology, microstructure and sizes of soot particles directly sampled in a spray flame fuelled with soy-methyl ester were investigated using transmission electron microscopy (TEM). The soot samples were taken at different axial locations in the spray flame, 40, 50 and 70 mm from injector nozzle, which correspond to soot formation, peak, and oxidation zones, respectively. The biodiesel spray flame was generated in a constant-volume combustion chamber under a diesel-like high pressure and temperature condition (6.7 MPa, 1000K). Density, diameter of primary particles and radius of gyration of soot aggregates reached a peak at 50 mm from the injector nozzle and was lower or smaller in the formation or oxidation zones of the spray.
2011-08-30
Technical Paper
2011-01-2002
Masakuni Oikawa, Yusuke Ogasawara, Yoshikazu Kondo, Kanan Sekine, Kaname Naganuma, Yasuo Takagi, Yoshio Sato
A new ignition-combustion concept named PCC (Plume Ignition Combustion Concept), which ignite rich mixture plume in the middle of injection period or right after injection of hydrogen is completed, is proposed by the authors in order to reduce NOx emissions in high engine load conditions with minimizing trade-offs on thermal efficiency. In this study fundamental requirements of hydrogen jet to optimize PCC are investigated by using single and multi-hole nozzle with a combination of high speed laser shadowgraphy to visualize propagating flame. As a result, it was infered that igniting the mixture plume in the middle of injection period with minimizing jet penetration to chamber wall is effective reducing NOx formation even further.
2011-08-30
Journal Article
2011-01-2001
Thomas Wallner, Nicholas S. Matthias, Riccardo Scarcelli
Energy security and climate change are two of the main drivers for development of sustainable and renewable transportation solutions. Entities around the globe have been working on strategic plans to reduce energy consumption and curb greenhouse gas emissions. In this context hydrogen is frequently mentioned as the fuel and energy carrier of the future. The U.S. Department of Energy's (DOE's) FreedomCAR and Vehicle Technologies (FCVT) Program has identified hydrogen-powered internal combustion engine (ICE) vehicles as an important mid-term technology on the path to a large-scale hydrogen economy. DOE has set challenging goals for hydrogen internal combustion engines including 45% peak brake thermal efficiency (BTE). This paper summarizes recent research engine test results employing hydrogen direct injection with different injection strategies.
Viewing 1 to 30 of 46025

Filter

  • Range:
    to:
  • Year: