Search Results

Pressure-time variations are recorded in the intake pipe and crankcase of a motored, crankcase compression, piston ported, loop scavenged two stroke cycle engine over a range of engine speeds from 2000-7000 rpm, for several intake pipe lengths and different inlet port timings. These pressure-time histories are presented together with the results of theoretical calculations, which include unsteady flow in the induction tract. Predicted delivery ratio trends are compared with measured values over the range of engine speeds and inlet tract lengths for different inlet port timings.

This paper attempts to illustrate some of the reflection characteristics of exhaust systems, suitable for piston ported, crankcase compression, naturally aspirated two-cycle engines. In particular, the application is even narrower, being concerned principally with those engines of the spark ignition, gasoline burning type where a high bmep is desirable. The two principal exhaust systems considered are the diffuser and the expansion chamber. Both are analyzed experimentally and theoretically and presented as measured and digitally computed pressure-time diagrams in simulated and actual engine exhaust systems. These are compared and discussed.

The theoretical modelling of the scavenge process for a naturally aspirated two-cycle engine is described and employed in conjunction with an unsteady gas dynamic analysis of flow in the engine ducting. Programmed for a digital computer, the results of this theoretical study are shown in relation to a 250 cm3 engine with values of predicted charging efficiency, scavenging efficiency, and delivery ratio given as a function of engine speed. These are compared with measured values of scavenging efficiency and the usual performance characteristics of power, mean effective pressure, delivery ratio, and specific fuel consumption. Also compared are the measured and predicted pressure diagrams taken in the cylinder, the crankcase, and the exhaust and inlet ducts. The design of a somewhat unique cylinder gas sampling valve of the mechanical type is described and its usage discussed both theoretically and practically.

Measurement of pressure-time histories in the exhaust system of a naturally aspirated internal combustion engine poses some difficult instrumentation problems. This paper describes an experimental and theoretical approach in tackling this research. The exhaust system is simulated by pulses of compressed air at a frequency of up to 4000 pulses/minute, that is, a 1 cyl 4 stroke cycle engine running at 8000 rpm. The pressure-time histories are calculated by digital computer in terms of the cylinder, exhaust valve, and pipe friction characteristics and compared with the experimental pressure-transducer records at various positions in the exhaust system.

Modern turbocharged diesel engines employ exhaust driven turboblowers operating at high speeds up to 100,000 rpm. The performance assessment of such units demands precise and controllable power absorption and torque measurements at these very high rotational speeds. Additionally the parameters, speed, mass flow, static and dynamic pressures and temperatures must be measured. The turbine power absorption and torque measutement present unique problems. The remaining parameters may present some difficulties but generally the problems are not so great. The design of a high speed dynamometer and the development problems encountered are described. The dynamometer has been used to establihs the performance characteristics of a C. A. V. 01 turbocharger and these are reported.

Engine cycle simulation is an essential tool in the development of modern internal combustion engines. As engines evolve to meet tougher environmental and consumer demands, so must the analysis tools that the engineer employs. This paper reviews the application of such a tool, VIRTUAL 4-STROKE [1], in the modelling of a benchmark 1.9 Litre TDI engine. In an earlier paper presented to the Society [2] the authors presented results of a validation study on the same engine under full load operation. This paper expands on that work with validation of the simulation model against measured data over a full range of part load operation.

The emissions produced from a simple carburetted crankcase scavenged two-stroke cycle engine primarily arise due to losses of fresh charge from the exhaust port during the scavenging process. These losses lead to inferior fuel consumption and a negative impact on the environment. Pressure on exhaust emissions and fuel consumption has reduced the number of applications of the two-stroke cycle engine over the years, however the attributes of simplicity, high power density and potential low manufacturing costs have ensured its continuing use for mopeds and motorcycles, small outboard engines and small utility engines. Even these last bastions of the simple two-stroke engine are being challenged by the four stroke alternative as emissions legislation becomes tighter and is newly formulated for many categories of engines. A simple solution is described which reduces short circuit and scavenge losses in a cost effective way.

An experimental and theoretical investigation to minimise the hydrocarbon emissions from a 25 cm3 two-stroke engine with finger transfer ports is described. Finger ports have the side of each passage closest to the cylinder axis open to the cylinder bore making it possible to produce high-pressure die castings with the simplest of dies. Cylinders utilising this type of porting are believed to have inferior scavenging characteristics compared to those using closed or cup-handle porting. The effects of cylinder scavenging characteristics and port optimisation on engine performance were examined using a computer simulation. It is concluded that there is potential for a 70% reduction in exhaust hydrocarbon emissions through scavenging efficiency improvements and port optimisation, provided the cylinder scavenging can be developed to match that of the best existing unconventional crossflow scavenged designs.

Previous papers published by the author have described unsteady gas flow through a naturally aspirated two-cycle engine and the most recent of these publications details a theoretical modelling of the gas exchange or scavenge process for the cylinder of this type of power unit. This results in the ability to predict the trapped charge state, mass, and purity characteristics. With such information it becomes sensible to apply a closed cycle thermodynamic analysis to it and to further predict directly power, torque, and fuel consumption characteristics. This paper describes such a simple closed cycle analysis and compares the theoretical results of power, mean effective pressure, specific fuel consumption, and cylinder pressure diagrams with corresponding measured data from two engines.

Earlier papers by the principal author in conjunction with others have described the prediction of noise and performance characteristics of two-cycle spark-ignition crankcase compression engines. These calculations are performed on a digital computer and are shown to simulate accurately the unsteady gas flow and thermodynamic processes in such power units. The engines described previously had induction control by the piston or with a disc valve. In this paper the work is extended to engines fitted with reed valves controlling intake air flow and examples illustrating the effectiveness of such calculations are presented. In particular, a single-cylinder industrial engine is employed to show clearly the effects of changing such parameters as reed petal thickness, stop-plate radii and numbers of reed petals on the performance characteristics.

In two previous papers to this Society (1, 2)* an ‘alternative’ method was presented for the prediction of the unsteady gas flow behaviour through a reciprocating internal combustion engine. The computational procedures led further to the prediction of the overall performance characteristics of the power unit, be it operating on a two- or a four-stroke cycle. Correlation with measurements was given to illustrate its effectiveness and accuracy. In the ducts of such engines there are inevitably sectional changes of area which are either gradual or sudden. A tapered pipe is typical of a gradual area change whereas a throttle or a turbocharger nozzle represents a sudden area change. In those previous papers it was indicated that a fuller explanation, of the theoretical procedures required to predict accurately the unsteady gas flow in such duct sections would be given in a later paper to this Society; this is that necessary publication.

The application of in-cylinder multi-dimensional modelling to the scavenging process within the cylinder of a two-stroke cycle engine requires a prior knowledge of the flow entering that cylinder. Without this information, assumptions must be made which limit the accuracy of the theoretical simulation. This paper describes laser doppler anemometry measurements of transfer port efflux flow for a two-port loop scavenged test cylinder motored at 200 rev/min. The cylinder was externally blown to ensure scavenge flow into the cylinder over the entire transfer port open period. The test results indicate that the flow does not enter the cylinder in the port design direction, but varies as a function of port height during both port opening and closing. Comparison of motoring results with those obtained under steady flow testing of the same cylinder, shows adequate correlation, thereby justifying the use of steady flow information for dynamic simulation.

The paper discusses the application of maps of measured discharge coefficients for poppet valves, cylinder ports, and in-pipe throttles within a theoretical simulation of the unsteady gas flow through an internal combustion engine. The maps provided cover both inflow and outflow at the discontinuity being discussed and are displayed as contour maps of the discharge coefficient as some function of the geometrical flow area of that discontinuity and of the pressure ratio across it up to a maximum value of 2.0. An engine simulation package is used for both a four-stroke and a two-stroke engine to determine the typical pressure ratio and area ratio characteristics which pertain at all such discontinuities at representative engine speed and load conditions.

A three cylinder two-stroke cycle diesel engine is proposed for automotive use. The engine is of the simple loop or cross-scavenging type with a crosshead seal and under piston scavenging pump. This paper records the initial investigations of this concept using a purpose built single cylinder engine. Results from different combustion systems are presented together with tests with the same engine when using an external air supply. Measurements from a parallel investigation using a laser doppler anemometer to measure air swirl motion within one of the chambers are also presented.

In 1968 Professor Alfred Jante published an SAE paper detailing a method of assessing the scavenging behaviour of a two-cycle engine. It was a simple technique involving motoring the engine and measuring the (cylinder head removed) velocity contours at the cylinder head level using pitot tubes. It attracted wide attention in industry, but with varying degrees of acceptance and results. This paper attempts to establish in a logical manner and with a considerable’ volume of experimental data that the method proposed by Jante has real relevance, but to obtain acceptable accuracy in terms of predicting good and bad scavenging for particular engine cylinders the results have to be analysed rather more carefully and completely than the approach adopted by Jante.

This paper reports on the experimental evaluation of certain aspects of the mathematical modelling by the GPB method of pressure wave propagation through finite systems, of unsteady gas flow in engine ducting. The aspects under examination are the propagation of pressure waves through a pipe which contains gases of dissimilar properties. In this case the gases are carbon dioxide and air. The experimentation is conducted using the QUB SP (single pulse) pressure wave generator consisting of a cylinder, connected via a sliding valve to a long duct. The pressure waves it creates closely mimic those to be found in i.e. engines. The initial cylinder pressure may be set to simulate either an induction or an exhaust process, but the experiments reported here are of compression waves only. The duct attached to the pressure wave generator is a straight pipe. The cylinder and part of the pipe are filled with carbon dioxide and air.

This paper reports on the first phase of an experimental evaluation of four different methods for the mathematical modelling of unsteady gas flow in a pipe system containing an area discontinuity. The four methods under investigation are the non-homentropic method of characteristics, the two-step Lax-Wendroff method with flux corrected transport, the Harten-Lax-Leer upstream difference method and the GPB finite system method. The experimentation is conducted using the QUB SP (single-pulse) pressure wave generator consisting of a cylinder, connected via a sliding valve to a long duct. The pressure waves it creates closely mimic those to be found in i.c. engines. The initial cylinder pressure may be set to simulate either an induction or an exhaust process. Various ducts are attached to the pressure wave generator to simulate both sudden and gradual area changes. Each duct is sufficiently long as to permit pressure wave observation without superposition effects.

This paper reports on the first phase of an experimental evaluation of five different methods for the mathematical modelling of unsteady gas flow in engine ducting. The five methods under investigation are the homentropic method of characteristics, the non-homentropic method of characteristics, the two-step Lax-Wendroff method with flux corrected transport, the Harten-Lax-Leer upstream difference method and the Blair method of pressure wave propagation through finite spaces. A single cycle pressure wave generator consisting of a cylinder, connected via a sliding valve to a long duct, has been designed and built. The pressure waves it creates closely mimic those to be found in i.e. engines. The cylinder and the ducts of the device can be filled with any gas and at elevated temperatures. A perfect seal exists between the cylinder and the valve thus enabling mass- flow correlation. The initial cylinder pressure may be set to simulate an induction or an exhaust process.

This paper reports on the use of mathematical modelling by the GPB method of pressure wave propagation through finite systems, for the design of prototype exhaust systems and silencers for a Harley-Davidson motorcycle. The motorcycle engine is the classic 1340 cm3 45° V-twin power unit. The design objectives were to gain mid-range power and torque without loss of performance at either end of the speed range and to design silencers which would enhance the performance and the noise image of the machine. The Queen's University of Belfast (QUB) (3)* employed their unsteady gas flow modelling techniques to the design of the system and its silencers to complement a new camshaft design from Crane Cams. The results of the use of these computer based design techniques are reported as performance characteristics of power and torque for the new design by comparison with the stock system.

This paper describes the initial investigation and design of a lightweight racing motorcycle with a single-cylinder 2-stroke engine, capable of producing 60 bhp. The data discussed here pertain to the gas dynamic and mechanical parts and functions of the cycle. Designs of the various components are described and reports of tests on road and test beds verify the viability of this concept of a high specific output and large displacement cylinder for a lightweight, air-cooled motorcycle engine.