Search Results

This paper presents results and discussions of two hundred hours endurance test carried on single cylinder four-stroke cycle LPG cargo pickup van engine. Engine was run in cycle as suggested by manufacturer. Engine was run for one hour at speed corresponding to maximum torque and then it was run for one hour at speed corresponding to maximum power. This cycle was repeated for two hundred hours. Effects of endurance test on components of engine were studied. Engine was tested before endurance test at full throttle position and same engine was tested after endurance test at full throttle position. Performance of engine before and after endurance test has been compared and discussed. Objective of this experimental work was to study effect of endurance test on different components of engine and analyze and compare performance of engine before and after endurance test. Graphs of important engine parameters have been plotted and curve fitting has been done.

As competent and low-pollution alternative fuel, CNG has revealed its excellence over engine performance and emissions. In recent years, CNG is considered as the diesel engine alternative fuel for heavy-duty engine applications due to its lower emissions and cost effective after-treatment systems. Due to the implementation of stricter emission norms over the years, the evolution of the fuel supply system has become more robust and electronically controlled. In the case of CNG engines, most of the engines were equipped with MPFI fuel system, for its precise fuel control abilities and controlling emission parameters. However, this MPFI system encompasses severe design changes in the intake manifold and is cost worthy to OEMs over the SPFI fuel system. MPFI system adds on the overall cost of the engine unit and its maintenance when compared to SPFI system.

Particulate matter is one of the major pollutant responsible for deteriorating air quality, particularly in urban centers. Information on contributing sources with the share from different sources is a first and one of the important steps in controlling pollution. Diverse sources, anthropogenic as well as natural, like industries, transport, domestic burning, construction, wind-blown dust, road dust contribute to particulate matter pollution. Receptor modeling is a scientific method which is utilized for assessment of the contribution of various sources based on chemical characteristics of particulate matter sources and ambient air particulate matter. Representative data of fractions of various chemical species in the particulate matter from the different sources i.e. source fingerprint is an essential input for the receptor modeling approach.

In this experimental study four stroke, four cylinder, MPFI, SI engines were tested as per IS 14599. A group of six bifuel engines with different specifications was tested in gasoline mode and LPG mode. Engines were converted by using modification system to operate in LPG mode. Objective of this experimental study was to compare performance and emissions of PFI passenger car engines in gasoline mode and LPG mode and to establish generic performance trend for LPG/Gasoline bifuel engines by defining and computing normalized figure of merit, power per unit displacement. From experimental results, generic performance trend for passenger car engines was established. A unit parameter KW/lit was calculated for each engine for comparison in relation to rated torque, maximum exhaust gas temperature and speeds corresponding to maximum torque and maximum power.

The ever-increasing energy demand is a prime concern of entire world. As gasoline prices soar and concern over harmful emissions mount, vehicles which run on alternate fuel sources like LPG and CNG are becoming increasingly important. In this experimental study single cylinder pickup van engine was tested as per IS 14599 by using LPG and CNG as fuel. Ordinary fuel for vehicle is gasoline. Full throttle performance was tested at different speeds on computerized engine test set up with data acquisition system and AVL eddy current dynamometer. Important performance characteristic curves have been investigated and compared in CNG mode and LPG mode. Curve fitting has been done and equations with regression coefficient have been derived. Statistical analysis for different engine parameters has been done in LPG and CNG mode by using matlab software. It was observed that maximum power and maximum torque in LPG mode was more than that in CNG mode.

The objective of this project is to design of gas mixer venturi as per IS4477 and simulation of dual fuel (Diesel-CNG) engine for performances parameters to examine the BSFC using GT-suite. In present work; a 59 kW diesel engine of 18.5 compression ratio has been converted to operate on dual fuel (Diesel-CNG) keeping same compression ratio with improved fuel economy. Natural gas is an excellent fuel. Its combustion and emission characteristics are superior to any other realistic competing fuel. There are advanced technologies like closed loop lambda control system and lean combustion are incorporated in the engine to achieve the performance targets. In the initial stage; experimental testing is conducted for base diesel engine on engine dynamo for performance parameters. Experimental testing data and design data's of base diesel engine are used as input in GT-Suite to predict the performance of the base diesel engine.

The evolution of engine technology has so far seen the most beneficial side of progress in the fields of transportation, agriculture, and mobility. With the advent of innovation, there is also an impact on our environment that needs to be balanced. This is where fuels like CNG, LPG, LNG, etc. outperform conventional fossil fuels in terms of pollution & operational cost. This paper enlightens on the use of innovative dual-fuel technology where diesel & CNG fuels are used for combustion simultaneously inside the combustion chamber. Dual fuel system adaptation for farm application ensures self-reliance of the farmer where he can generate Bio-CNG to use the renewable fuel for farming making him less dependent on conventional fossil fuel thus promoting a green economy. The dual-fuel system is adapted to the existing in-use diesel engine with minimum modifications. This makes it feasible to retrofit a CNG fuel system on an existing diesel engine to operate it on dual fuel mode.

Towards the effort of reducing pollutant emissions, especially soot and nitrogen oxides, from direct injection Diesel engines, engineers have proposed various solutions, one of which is the use of a gaseous fuel as a partial supplement for liquid Diesel fuel. These engines are known as dual fuel combustion engines. A dual fuel (Diesel-CNG) engine is a base diesel engine fitted with a dual fuel conversion kit to enable use of clean burning alternative fuel like compressed natural gas. In this engine diesel and natural gas are burned simultaneously. Natural gas is fed into the cylinder along with intake air; the amount of diesel injection is reduced accordingly. Dual fuel engines have number of potential advantages like fuel flexibility, higher compression ratio, and better efficiency and less modifications on existing diesel engines. It is an ecological friendly technology due to lower PM and smoke emissions and retains the efficiency of diesel combustion.

CNG has proven to be a concrete alternative to gasoline and diesel fuel for sustained mobility. Due to stringent emission norms and sanctions being imposed on diesel fuel vehicles, OEMs have shifted their attention towards natural gas as an efficient and green fuel. Newly implemented BS VI emission norms in India have stressed on the reduction of Nitrogen Oxides (NOx) from the exhaust by almost 85% as compared to BS IV emission norms. Also, Indian Automotive market is fuel economy cautious. This challenges to focus on improving fuel economy but without increase in NOx emissions. Exhaust Gas Recirculation (EGR) has the potential to reduce the NOx emissions by decreasing the in-cylinder temperature. The objective of the paper is to model a CNG TCIC engine using 1D simulation in order to optimize the NOx emissions and maintain exhaust temperatures under failsafe limits.

Due to increasing pollution and climatic cries, newly implemented BS-VI emission norms in India have stressed the reduction of emission. For which many automobiles have been shifted to alternate fuels like CNG. Also, the Indian Automotive market is fuel economy cautious. This challenges to focus on improving fuel economy but without an increase in emissions. Crankcase blow-by gases can be an important source of particulate emission as well as other regulated and unregulated emissions. They can also contribute to the loss of lubricating oil and fouling of surface and engine components. Closed Crankcase Ventilation (CCV) or Open Crankcase Ventilation (OCV) is capable to reduce particulate emissions by removing the oil mist that is caused mainly due to blow-by in the combustion chamber. This paperwork is focused, to measure the effectiveness of the CCV and OCV systems on the engine-out emissions, primarily on the particulate emissions.

This paper discusses experimental outcome of port fuel injected engines operated on gasoline mode and LPG mode. Eight Passenger car PFI engines were tested by using computerized engine data acquisition and control system on gasoline mode and LPG mode. Objectives of this experimental study were 1) To establish generic performance trend for group of newly introduced gasoline/LPG passenger car bi-fuel engines in Indian market. This trend has been established. 2) To compare performance of one sample engine in gasoline and LPG mode. This performance has been compared from performance characteristics curves in both modes. 3) To establish methodology to compare and contrast the performance of various types of Gasoline/LPG passenger car engines. This methodology has been established for a group of engines. 4) To define new normalized figure of merit suitable for the performance comparison of passenger car engines. A parameter power per unit displacement has been defined.

Biodiesel is an alternative fuel for diesel which is made through a chemical process which converts vegetable oils and fats of natural origin into fatty acid methyl esters (FAME). The most usual method to transform Bio-oil into biodiesel is Transesterification that can be carried out using different catalyst systems. Jatropha is second generation, non-edible oil and can be used for producing biodiesel. The Transesterification reaction consists of heating jatropha oil with proper concentration of methanol at appropriate temperature in the presence of catalyst. After reaction, the mixture is allowed to settle down for 8-10 hrs. Two separate layers, top layer of biodiesel and lower layer of glycerol will form, which can be separated. Reaction temperature, amount of methanol, catalyst and reaction time are important parameters which decide yield and quality of biodiesel.

Environmental pollution has proven to be a big threat to our eco-system and pollution from automobiles using conventional fuels is a major contributor to this. Alternative fuels are the only immediate option that can help us counter the ever rising environmental pollution. In today’s date we cannot directly replace an IC engine, so the most efficient option available is using a fuel that can work with the IC engines other than gasoline and diesel. CNG proves to be the most promising fuel. A diesel engine converted to stoichiometric CNG engine was used for optimization. The paper deals with the improvement of engine power from 50HP to 60HP and up-gradation of the emission from BS-III to BS-IV norms of a multi-cylinder naturally aspirated engine. This was achieved by varying the compression ratio, valve-lift profile, intake plenum volume, runner length, spark-advance timing, fuel injection location, exhaust pipe length and catalytic converter selection.

Automotive engine emissions are disturbing the ecological system and it has caused major impact on flora & fauna and environment. The major motive force behind this research is to find the alter-native fuel for the future sustainable mobility and less dependence on the fossil fuels. Biodiesel fuel produced from non-edible oil (like castor) could be used to replace a considerable portion of the conventional fuel consumed worldwide. Castor oil is selected for this study considering a fact that India is a major contributor in global castor oil seed production and also it, being a non-edible oil, avoids the cold-war between food vs fuel. The present study has been conducted in three phases.