Search Results

The open jet wind tunnel is a widespread test section configuration for developing full scale passenger cars in the automotive industry. However, using a realizable nozzle cross section for cost effective aerodynamic development is always connected to the presence of wind tunnel effects. Wind tunnel wall interferences which are not present under open road conditions, can affect the measurement of aerodynamic forces. Thus, wind tunnel corrections may be required. This work contains the results of a CFD (Computational Fluid Dynamics) approach using unsteady Delayed Detached Eddy Simulations (DDES) to evaluate wind tunnel interferences for open jet test sections. The Full Scale DrivAer reference geometry of the Technical University of Munich (TUM) using different rear end shapes has been selected for these investigations.

In open jet wind tunnels with high blockage ratios a sharp rise in drag is observed for models approaching the nozzle exit plane. The physical background for this rise in drag will be analyzed in the paper. Starting with a basic analysis of the dependencies of the effect on model and wind tunnel properties, the key parameters of the problem will be identified. It will be shown using a momentum balance and potential flow theory that interaction between model and nozzle exit can result in significant tunnel-induced gradients at the model position. In a second step, a CFD-based investigation is used to show the interaction between nozzle exit and a bluff body. The results cover the whole range between open jet and closed wall test section interaction. The model starts at a large distance from the nozzle, then moves towards the nozzle, enters the nozzle and is finally completely inside the nozzle.

In this work we extended the findings from a previous study by the authors on the mechanisms and influence factors of deposit formation in urea-based selective catalytic reduction systems (SCR) [1]. A broader range of operating conditions was investigated in detail. In order to quantify the boundary conditions of deposition, a representative set of deposits was studied during formation and decomposition. A box of heat resisting glass was equipped with a surrogate mixing element to monitor solidification timescales, temperatures and deposit growth. A chemical analysis of the deposits was performed using thermogravimetry. The depletion timescales of individual deposit components were systematically investigated. A moderate temperature increase to 350 °C was deemed sufficient to trigger fast decomposition of deposits formed below 250 °C.

A region with floor boundary-layer suction upstream of the vehicle to remove the oncoming boundary layer is often used in automotive wind tunnels. These suction systems inevitably change the empty-tunnel pressure gradient. In this paper, the empty-tunnel pressure gradient created by the use of boundary layer suction and its effect on measured drag are investigated. By using excess suction - more suction than necessary to remove the floor boundary layer – it was possible to show experimentally that the major part of the drag increase due to boundary layer suction is created by unintended gradient effects. Only a minor part of the drag increase is due to the increased flow velocities at the lower parts of the vehicle, or in other words, due to the improved ground simulation. A theoretical model, using the concept of horizontal buoyancy to predict the gradient effect, is proposed. The model is compared to the experimental results as well as to CFD calculations.

Today's car designers ask for compact and light-weighted headlamps with several new functional features and special stylistic elements. This yields in new lighting technology such as modern free form and ellipsoid module reflectors with small dimensions and the need to use highly sophisticated materials. Both of this is sensitive to the amount of temperature and at a critical level may cause irreversible damage. Therefore, it is necessary to predict temperature loads at an early development stage in order to ensure new headlamp concepts and to shorten development time. An approach to calculate and analyze temperatures in headlamps by continuum fluid dynamic methods (CFD) is presented which can be compared and correlated to measurements carried out with infrared thermography and demonstrates the benefit of this method.

Minimizing the lap time for a given race track is the main target in racecar development. In order to achieve the highest possible performance of the vehicle configuration the mutual interaction at the level of assemblies and components requires a balance between the advantages and disadvantages for each design decision. Especially the major shift in the focus of racecar powerunit development to high efficiency powertrains is driving a development of lean boosted and rightsized engines. In terms of dynamic engine behavior the time delay from requested to provided torque could influence the lap time performance. Therefore, solely maximizing the full load behavior objective is insufficient to achieve minimal lap time. By means of continuous predictive virtual methods throughout the whole development process, the influence on lap time by dynamic power lags, e.g. caused by the boost system, can be recognized efficiently even in the early concept phase.