Search Results

Clutch judder phenomenon is known as a vehicle vibration caused by the drive torque fluctuation from the clutch unit at takeoff. In this paper, a novel strategy for improving clutch judder phenomenon caused by the movement/tolerance between mechanical parts comprising the clutch system is introduced. In order to simulate the movements of the clutch system and of the vehicle drivelines precisely, we used numerical analysis software and have achieved high-grade prediction of the clutch torque fluctuation and the vehicle vibration. Using this method, we have developed a high-quality clutch system that enables smoother clutch engagement, and at the same time, development efficiency has been improved.

Brazing using arc-sprayed coatings was investigated for application to non-oxidation copper brazing. It was found that the more porous sprayed coatings have an excellent brazeability. This newly developed joining method is more suitable than conventional methods for brazing complicated parts. We have applied this method to fabricate a torque converter for practical use.

Recently, for the protection of the environment, the regulation of automobile fuel consumption and exhaust gas emission has been strengthened. To improve fuel economy, it is demanded that each engine part contributes to reducing the workload of the engine, even the engine lubrication oil pump. In response to this, a new variable discharge oil pump was developed. It is the world's first internal gear type oil pump that has electronically controlled continuously variable discharge. The work performed by the pump chiefly takes two forms: sliding friction of the rotor and pumping work which moves the oil. First, in developing a variable discharge oil pump, a new tooth profile of the rotor was developed to reduce its sliding friction. As a result, the sliding friction of the rotor was reduced by 34% while maintaining the same theoretical oil discharge rate. Next, a variable discharge mechanism using an internal gear was developed.

Over the past decades, the automotive industry has made significant efforts to improve engine fuel economy by reducing mechanical friction. Reducing friction under cold conditions is becoming more important in hybrid vehicle (HV) and plug-in hybrid vehicle (PHV) systems due to the lower oil temperatures of these systems, which results in higher friction loss. To help resolve this issue, a new internal gear fully variable discharge oil pump (F-VDOP) was developed. This new oil pump can control the oil pressure freely over a temperature range from -10°C to hot conditions. At 20°C, this pump lowers the minimum main gallery pressure to 100 kPa, thereby achieving a friction reduction effect of 1.4 Nm. The developed oil pump achieves a pressure response time constant of 0.17 seconds when changing the oil pressure from 120 kPa to 200 kPa at a temperature of 20°C and an engine speed of 1,600 rpm.

We have developed a Hall effect device based height sensor of a smaller size, and with higher temperature operation durability, as compared to conventional devices. Downsizing of the sensor is realized by decreasing a number of parts, and by employing a short bearing. Improvement in heat resistance is achieved by adopting an IC with sufficient heat resistance and a SmCo magnet with high coercive force. In addition, a sensor of a high degree of accuracy is accomplished by improvements in linearity and robustness of magnetic characteristics. Development of a small, heat-resistant and accurate height sensor will promote the spread of systems using a height sensor, such as a High Intensity Discharge (HID) headlamp.

One of the problems concerning T/M is conventionally how “Improving the input torque as the engine gets higher power” and “Making product lighter in weight and more compact to improve the fuel consumption” can be realized at the same time. To realize these things at the same time, it is needless to say that the gears must be stronger. For the “pitting fatigue strength” which is quoted as a problem lately, the fatigue mechanism has not been clarified, yet. Therefore, it is now a big problem how to achieve high strength. In the meantime, we tried to develop the production engineering for “finer crystal grains” and “fine-dispersion precipitation of carbo-nitrides,” and succeeded in improving “pitting fatigue strength” remarkably. Such results will be reported in the following sections:

AISIN SEIKI CO., Ltd. Started the production of electronically controlled hydraulic automatic transmissions for medium-duty trucks and buses in 1989. The number of vehicles on the Japanese market in which this system is adopted is increasing steadily. After re-examining market needs, AISIN SEIKI CO., Ltd. has newly developed an electronically controlled hydraulic automatic transmission A580 which focuses on improved input capacity, driving performance and fuel economy for medium-duty trucks and buses and lessens learnt from experience.

We have developed a power sliding door (PSD) system driven by a push-pull cable. The door closure and slide are operated by different actuators to limit the force required for a compact, light-weight drive unit. This paper introduces the concept of the PSD system using a push-pull cable drive. Two new technologies to achieve the PSD system are also described. One is the door position control for increasing the push-pull cable reliability. The other is a compact position sensor to accurately detect the sliding door's position.

As a process that enables the high-speed and continuous forming of lengthy materials with a constant cross-sectional configuration, roll forming offers much higher productivity than the stamping process. However, in case a change must be made to the shape of the cross section, the material must normally be stamped or joined with a part containing a separate shape. This affects productivity, increases the number of pieces, and degrades the material's appearance. This report describes the roll-forming technology that we developed, in which the cross section of the material can be changed gradually. This method adopts a system which uses a movable and rotatable roll-stand that enables high-speed, continuous roll-forming processes.

The conventional hydraulic valve lifters, which eliminate the valve clearance adjustment, normally use the pressurized engine lubricant for the working fluid. We have developed a quite new type lifter, named “self-contained hydraulic valve lifter”, which possesses the working fluid in itself. Because the new type lifter is independent of the pressurized engine lubricant, it has some advantages, especially that it can be applied to the existing engine using the mechanical valve gear without almost any engine modifications. And we have confirmed that the self-contained hydraulic valve lifter has good characteristics and reliability and have applied it to the mass production engine (i.e. Toyota 1.3L gasoline engine) for the first time in the world. This paper describes the construction, the characteristics and the reliability of this lifter.

Drive train components (transmission, differential gears, etc.) can be made smaller and lighter if the excessive torque exerted on them can be reduced during the quick start of a vehicle. An orifice put in the hydraulic clutch piping path is an effective method. However, increased oil viscosity at low temperatures (0°C or below) makes the “pedal feel” worse. In order to increase the orifice diameter for better “pedal feel”, a shape memory alloy spring, for operation at low temperatures, was developed by adding cobalt to the nickel-titanium alloy. Consequently, a Variable-Orifice valve, using the shape memory alloy spring, is practical.

There are such outside door handles called smart handles which have a transmitting antenna, a lock/unlock sensor, and a sensor detection circuit, with which operation of door lock is possible just by "touching" the electrostatic-capacitance type sensor of the handles.As the design of the outside handles, body color painting and Cr plating are adopted. However, if plating is applied over the entire surface of a smart handle, electromagnetic waves transmitted from the antenna will be blocked since plating material is electrically conductive. In addition to this, touching a part other than the sensor may change the electrostatic-capacitance of the sensor, which results in unwanted functioning of the lock/unlock sensor. Because of this, only part of the handle, which does not hinder the transmission of electromagnetic waves and does not cause unwanted functioning, is covered by plating, that is called, "Partially plated specifications" (Figure 1).

Automating the inspection of the piston combustion chamber volume is difficult and prevents establishing an unmanned machining process of the piston in the future. So, we developed an inspection technique which uses a Range Finder, non-contact visual sensor, and calculate the chamber volume by integrating 3D position data. We applied this real-time measurement technique which enables 100 % inspection to our production lines. Then, we developed the “Defect Free Production Line”, which calibrates itself by feeding back the measured volume data to the machining process. Our paper will explain this inspection technique and our “Defect Free Production Line”.

Responsiveness is one of the main characteristics of a brake booster. The design of a tandem booster, with its two boosting chambers, has a negative influence on high responsiveness. This report, using the CFD method for the air flow analysis, shows the way we found the most suitable air passage within the space of the given design of the current production tandem booster.

As a part of our process engineering (planning) steps and in order to shorten the initial flow control after the implementation of a production system, we have been adopting countermeasures for defects that have been forecasted by the application of FMEA. However, due to this having to be done with limited information (which is dependent upon the skill level of the operator) and due to the fact that the effects of each particular countermeasure are not fully understood, we cannot be certain that the measures implemented during the planning stages are thorough enough. The current situation is that countermeasures for most issues are being handled during the initial flow control stages based on the trial-and-error method. Given this situation, normally, it would take us more than three months from the time of line-off (start of production) to achieve our target rate of capacity utilization.

When a clutch pedal is operated, the clutch pedal vibration and interior noise are mostly affected by the dynamic characteristics of the clutch cover assembly. We achieved a high correlation between vehicle test data and results using this method when exciting not only clutch system but also the engine system. Finally, we developed an excitation method to evaluate the dynamic characteristics of the clutch cover assembly.

A newly developed parking assist system, which is based on rear view camera, is disclosed. System features include ‘parallel parking aid’ with voice guidance message along with several guidelines superimposed onto the rear view camera image. Voice guide message helps driver understand appropriate timing for each procedure of parallel parking. The system was designed to let driver follow the system by voice message rather than visual guide information through the screen for safety reason. The guide algorism is designed under ‘two turns’ parking maneuvers so that required longitudinal parking space becomes minimal. A key development of this system, which is to design the guide algorism to avoid collision to adjacent vehicle during parallel parking operation, is also discussed in this paper. User can select either ‘parallel guide’ or ‘normal (such as garage parking)’ mode through touch screen switch on display surface.

Recycling SMC molded parts has become one of the most important and urgent subjects. This paper discusses a system to recover SMC molded parts and recycle them to original automotive products. “Sandwich structure” in the core layer of which regrinded filler is concentrically involved, is very useful for increasing the volume of involved regrinded filler. This structure provides more weight reduction of recycled parts.

1 There are two design challenges of the flow path switching valve in a three-stage variable discharge oil pump. The first is to obtain the required discharge pressure characteristics and the other is to prevent hydraulic vibration. Therefore, we established technologies to determine the shape of the valve and the valve housing that resolve these two challenges. The technology to obtain the required discharge pressure characteristics solves equations that are statically true, such as the equations for the equilibrium of forces and hydraulic orifice. The hydraulic vibration control technology derives a differential equation that takes transient behavior, including oil elasticity and inertia, into account first. Then, the derived equations are converted to a transfer function that indicates the valve behavior according to the input of oil pressure changes. And then the stability criterion is applied to judge whether hydraulic vibration occurs or not.

As automotive electronic systems advance, the wire harness is the mainstream for necessary wiring in resin-made motor-driven actuators with wire connection labor and purchased-parts accounting for the majority of costs. As a means to eliminating the harness, there is a method of forming the conductive material on the inside, but this method leads to cost increases when there is a comparatively large number of wires because the required die insertion time becomes longer and automatic insertion equipment becomes necessary. The following paper reports on an integrated high-speed process that combines stamping and injection molding into a single process.