Search Results

This paper provides a method that corrects errors induced by the empty-tunnel pressure distribution in the aerodynamic forces and moments measured on an automobile in a wind tunnel. The errors are a result of wake distortion caused by the gradient in pressure over the wake. The method is applicable to open-jet and closed-wall wind tunnels. However, the primary focus is on the open tunnel because its short test-section length commonly results in this wake interference. The work is a continuation of a previous paper [4] that treated drag only at zero yaw angle. The current paper extends the correction to the remaining forces, moments and model surface pressures at all yaw angles. It is shown that the use of a second measurement in the wind tunnel, made with a perturbed pressure distribution, provides sufficient information for an accurate correction. The perturbation in pressure distribution can be achieved by extending flaps into the collector flow.

The aim is to develop a theory to describe the aerodynamic behavior of active grille shutters (AGS). The theory correlates the cooling air mass flow and drag of a vehicle with the angle and number of air flaps on the AGS. The relatively simple mathematical formulation of this theory provides an insight into the aerodynamic behavior and characteristic curve shape of AGS. It illustrates how the number of air flaps changes and influences the shape of the AGS characteristic curve. The theory is validated by experiments using wind tunnel measurements on real vehicles with AGS. The comparisons show good agreement between theory and experiment.

Brake system development and testing is spread over vehicle manufacturers, system and component suppliers. Test equipment from different sources, even resulting from different technology generations, different data analysis and report tools - comprising different and sometimes undocumented algorithms - lead to a difficult exchange and analysis of test results and, at the same time, contributes to unwanted test variability. Other studies regarding the test variability brought up that only a unified and unambiguous data format will allow a meaningful and comparative evaluation of these data and only standardization will reveal the actual reasons of test variability. The text at hand illustrates that a substantial part of test variability is caused by a misinterpretation of data and/or by the application of different algorithms.

Variation of the geometric compression ratio in gasoline combustion engines during engine operation enables potential for decreasing fuel consumption as well as emissions. One way to achieve a variable geometric compression ratio (VCR) is the application of a connecting rod with a variable effective length between its large end and its small end. Such a system consists of a connecting rod body with an eccentrically supported piston pin and a linkage which is supported hydraulically. Therefore, the connecting rod evolves from a solid part to a complex assembly of mechanical and hydraulic parts. In order to deploy this system in the most efficient way, an understanding of the physics and the dynamic behavior of the VCR connecting rod is necessary. This includes the mechanical subsystem as well as the hydraulic subsystem. This paper describes the experimental examination of a two stage variable connecting rod.

A new optical system to analyse 3D deformations crashed vehicles is in use at Porsche’s Crash Test Facility. This technology is based on the mathematical law that the spatial location of a point is clearly definable if it is represented by at least 2 images. With the help of an high resolution digital camera, highly developed image processing and photogrammetric algorithms, an automated deformation analysis system is realized. This new measurement technology has numerous advantages over conventional devices, such as coordinate measurement machines, multi section arms and analog photogrammetry. In one example of crash tests the application of this system is described. Comparisons with conventional measurement devices regarding accuracy, costs and process optimization are presented. An outlook to further innovations in analysis of safety tests, if photogrammetry is used as a basic technology, is given.

Although hydrogen ICE engines have existed in one sort or another for many years, the testing of fuel consumption by way of exhaust emissions is not yet a proven method. The current consumption method for gasoline- and diesel-fueled vehicles is called the Carbon-Balance method, and it works by testing the vehicle exhaust for all carbon-containing components. Through conservation of mass, the carbon that comes out as exhaust must have gone in as fuel. Just like the Carbon-Balance method for gas and diesel engines, the new Hydrogen-Balance equation works on the principle that what goes into the engine must come out as exhaust components. This allows for fuel consumption measurements without direct contact with the fuel. This means increased accuracy and simplicity. This new method requires some modifications to the testing procedures and CVS (Constant Volume Sampling) system.

In the present work we investigated experimentally and computationally the unsteady flow around a BMW car model including wheels*. This simulation yields mean flow and turbulence fields, enabling the study aerodynamic coefficients (drag and lift coefficients, three-dimensional/spatial wall-pressure distribution) as well as some unsteady flow phenomena in the car wake (analysis of the vortex shedding frequency). Comparisons with experimental findings are presented. The computational approach used is based on solving the complete transient Reynolds-Averaged Navier-Stokes (TRANS) equations. Special attention is devoted to turbulence modelling and the near-wall treatment of turbulence. The flow calculations were performed using a robust, eddy-viscosity-based ζ - ƒ turbulence model in the framework of the elliptic relaxation concept and in conjunction with the universal wall treatment, combining integration up to the wall and wall functions.

While race cars run in a highly dynamic environment, aerodynamic testing through state of the art wind tunnel tests, as well as CFD analyses, are mostly performed under static or stationary conditions. Therefore, other than track data, only very limited data are available on time resolved aerodynamic forces and pressures for a moving car. To investigate these effects a new model manipulator was developed which allows substantial pitch and heave movements up to 20Hz. Wind tunnel tests with a former LeMans type race car model have shown that the difference between a steady state and a true dynamic analysis is significant.

The increasing complexity of communication protocols for asynchronous multiplex systems requires the use of simulation during the optimisation of these protocols or the integration of other control units. Consideration of realistic communication behaviour of the connected control units is essential for performance analysis of multiplex systems. For a first pass, the use of simple statistical distributions (e.g. Poisson distribution) is suitable to get some simulation results. A better way to get realistic results is the approximation of empirical communication data through the use of more complex statistical distribution (e.g. mixed Erlang distributions). In this paper several approaches for the approximation of empirical data are presented. Beside simple statistical distributions (with one parameter), the use of more complex statistical distributions is discussed and methods for the identification of their parameters are presented.

The size of the room surrounding the wind tunnel test section, the so called wind tunnel plenum, is always seen as an important parameter of the wind tunnel building, but has rarely been the subject of systematic investigation regarding minimal requirements to meet quality objectives for aerodynamic testing. Experimental investigations of this object were made in a quarter-scale wind tunnel (nozzle area 1.4m2). The plenum dimensions were changeable by combinations of different side wall and ceiling positions. The results have shown, that the plenum can have a significant effect on the flow around the vehicle and therefore on the measured forces. Drag coefficient is under prediced if the wind tunnel plenum is too small. Recommendations are provided for the geometric dimensions of a wind tunnel plenum. The data obtained are a valuable tool for the layout of wind tunnel design concepts and for the evaluation of interference free wind tunnel simulation.

A detailed investigation of aerodynamic car testing in ¾-open-test-sections was made. Herein two main influencing variables (dimensionless length scales) could be identified: first, the relative length of the ¾-open-test-section influences the static pressure gradient along the x-axis and, second, the relative collector area has large effects on the wake of a car. The measured values (i.e. drag) are mainly determined by a combined effect of these two parameters. The basic investigation was made in the Porsche 1:4 model-wind-tunnel with two different types of vehicles {sportscar and van) and in two different scales (1:4, 1:5). The results are graphically summarized. This diagram can predict the differences between full size open-jet-wind-tunnels. These predictions were verified by measuring Porsche production cars and the Porsche calibration car in three other automotive wind-tunnels.

This paper presents an integrated numerical and experimental approach to take best possible advantage of the common development tools at hand (1D, CFD and wind tunnel) to determine the cooling air mass flow at the different vehicle development stages. 1D tools can be used early in development when neither 3D data nor wind tunnel models with detailed underhood flow are available. A problem that has to be resolved is the dependency on input data. In particular, the pressure coefficients on the outer surface (i.e. at the air inlet and outlet region) and the pressure loss data of single components are of great importance since the amount of cooling air flow is directly linked to these variables. The pressure coefficients at the air inlet and outlet are not only a function of vehicle configuration but also of driving velocity and fan operation. Both, static and total pressure coefficient, yield different advantages and disadvantages and can therefore both be used as boundary conditions.

In automotive open-jet wind tunnels reference velocity is usually measured in terms of a static pressure difference between two different cross-sectional areas of the tunnel. Most commonly used are two sections within the nozzle (Method 1: ΔP-Nozzle). Sometimes, the reference velocity is deduced from the static pressure difference between settling chamber and plenum (Method 2: ΔP-Plenum). Investigations in three full-scale open-jet automotive wind tunnels have clearly shown that determination of reference dynamic pressure according to ΔP-Plenum is physically incorrect. Basically, all aerodynamic coefficients, including drag coefficient, obtained by this method are too low. For test objects like cars and vans it was found that the error ΔcD depends on the test object's drag blockage in an open-jet wind tunnel.

This paper describes a novel approach for modeling an automotive HVAC unit. The model consists of black-box models trained with experimental data from a self-developed measurement setup. It is capable of predicting the temperature and mass flow of the air entering the vehicle cabin at the various air vents. A combination of temperature and velocity sensors is the basis of the measurement setup. A measurement fault analysis is conducted to validate the accuracy of the measurement system. As the data collection is done under fluctuating ambient conditions, a review of the impact of various ambient conditions on the HVAC unit is performed. Correction models that account for the different ambient conditions incorporate these results. Numerous types of black-box models are compared to identify the best-suited type for this approach. Moreover, the accuracy of the model is validated using test drive data.

The results of previous Life Cycle Assessments indicate the ecological dominance of the vehicle's use phase compared to its production and recycling phase. Particularly the so-called weight-induced fuel saving coefficients point out the great spectrum (0.15 to 1.0 l/(100 kg · 100 km)) that affects the total result of the LCA significantly. The objective of this article, therefore, is to derive a physical based, i.e. scientific chargeable and practical approved, concept to determine the significant parameters of a vehicle's use phase for the Life Cycle Inventory. It turns out that - besides the aerodynamic and rolling resistance parameters and the efficiencies of the power train - the vehicle's weight, the rear axle's transmission ratio and the driven velocity profile have an important influence on a vehicle's fuel consumption.

The Porsche 1:4-scale model wind tunnel was upgraded with a moving belt in combination with basic and distributed boundary layer suction devices. The belt is placed between the rotating wheels of the model with the external underfloor balance in operation. Special attention was given to providing a sufficient length of the belt with regard to road simulation for the aerodynamic optimization of race car models with their specific wake behavior. The boundary layer suction systems control the regions beyond the belt. Furthermore the balance was equipped with a pitch angle adjustment system in order to simulate the spring deflections of a moving vehicle. Results from a series of measurements taken from one race car model and one passenger car model are presented in order to investigate the influence of the boundary layer-, wheel rotation- and pitch adjustment-controls on the characteristic aerodynamic figures of the models.

BMW has introduced new test stands for noise measurements on passenger cars and motorcycles. Information is given on room conditions, machinery equipment, sound levels, frequency ranges and types of measurement. The semi-anechoic room is designed for measuring the sound distribution emitted by a single vehicle. Road influence is simulated by a reflecting floor and a roller-dynamometer. The free field sound distribution in terms of distance and direction is measured in the anechoic room. This room has high-precision installations for sound source identification and noise mapping. The reverberation room serves to measure sound power emitted by the test object. Its second purpose is to subject the bodywork to a high-power external sound source and to measure the sound-deadening effect of the passenger compartment. In conclusion, the presentation provides reports on the initial experience with these test facilities.

Current regulatory developments aim for stricter emission limits, increased environmental protection and purification of air on a local and global scale. In order to find solutions for a cleaner combustion process, it is necessary to identify the critical components and parameters responsible for the formation of emissions. This work provides an evaluation process for particle formation during combustion of a modern direct injection engine, which can help to create new aftertreatment techniques, such as a gasoline particle filter (GPF) system, that are fit for purpose. With the advent of “real driving emission” (RDE) regulations, which include market fuels for the particulate number testing procedure, the chemical composition and overall quality of the fuel cannot be neglected in order to yield a comparable emission test within the EU and worldwide.

The Hydrogen-Balance equation makes it possible to calculate the fuel economy or fuel consumption of hydrogen powered vehicles simply by analyzing exhaust emissions. While the benefits of such a method are apparent, it is important to discuss possible influencing factors that may decrease Hydrogen-Balance accuracy. Measuring vehicle exhaust emissions is done with a CVS (Constant Volume Sampling) system. While the CVS system has proven itself both robust and precise over the years, utilizing it for hydrogen applications requires extra caution to retain measurement accuracy. Consideration should be given to all testing equipment, as well as the vehicle being tested. Certain environmental factors may also play a role not just in Hydrogen-Balance accuracy, but as also in other low emission testing accuracy.

BMW - the driving force for progress As we approach the new millenium, to ensure the continuation of the progress into the future, BMW uses leading edge approaches in its materials research and processing. Overview production sites all over the world - Plant Dingolfing Quality requirements for automobile painting The complex and wide-ranging demands that the outer skin of an automobile has to meet offered us the chance to advance with a technological leap from liquid clear coat to the potentials of powder clear coat. The new clear coat technology The clear coat creates the ultimate gloss effect - and powder-based clear coat makes the surface of the car even more brilliant. To achieve this effect the body is covered by microscopically small paint particles. A pioneer achievement A lot of challenges in both material development and systems-engineering had to be made. The automotive world was watching, many experts said it could not be successfully used as an OEM clear coat.