Search Results

During the course of a fire and subsequent exposure to the environment, iron and low-carbon steels oxidize by two mechanisms: high temperature oxidation and atmospheric corrosion. Of particular interest to fire investigators are oxide properties and distribution that could be of use to better understand important characteristics of the fire such as the location the fire originated, the direction the fire traveled or even temperature versus time characteristics. This could be particularly valuable in cases where burn damage to combustible material, which is known to be an important indicator of fire origin, is so extensive that little if any material remains after the fire. However, there is little data in the literature that specifically addresses the utility of oxide properties in the context of fire investigations.

In some automotive electrical systems, it is advantageous to use power supplies and loads at two or more voltages. Often it is desirable to retain the single wire power architecture, with the car body providing the return circuit. A major difficulty in achieving this end is the matter of dealing with the possibility of a short circuit between feed wires at different voltages. It can be shown that source-side fuses cannot be relied upon to return the system to a safe state in all cases. Substantial effort was applied to this problem in the early years of the 21st century, but the results were less than completely satisfactory. Using entirely separate cable harnesses for each voltage, with physically separated routing, minimizes the risk of such a short occurring in the harness.

There is a limited amount of data currently available on the acceleration and braking performances of school buses. This paper analyzes the braking performance of various Type A and Type C school buses with hydraulic and air brakes. The effect of ABS and Non-ABS systems as well as driver experience is discussed. A comparison with passenger car braking performance is presented. The acceleration of a school bus is also presented. Evaluations of “normal” and “rapid” accelerations are presented for Type A and Type B buses. A comparison with commonly used acceleration values for various vehicles is presented.

Unintended acceleration events due to pedal misapplication have been shown to occur more frequently in older vs. younger drivers. While such occurrences are well documented, the nature of these movement errors is not well-characterized in common pedal error scenarios: namely, on-road, non-emergency stopping or slowing maneuvers. It is commonly assumed that drivers move in a ballistic or “direct hit” trajectory from the accelerator to the brake pedal. However, recent simulator studies show that drivers do not always move directly between pedals, with older drivers displaying more variable foot trajectories than younger drivers. Our study investigated pedal movement trajectories in older drivers ages 67.9 ± 5.2 years (7 males, 8 females) during on-road driving in response to variable traffic light conditions. Three different sedans and a pick-up truck were utilized.

The National Automotive Sampling System (NASS) Crashworthiness Data System (CDS) contains an abundance of field crash data. As technology advances and the database continues to grow over the years, the statistical significance of the data increases and trends can be observed. The purpose of this paper is to provide a broad-based, up-to-date, reference resource with respect to commonly sought-after crash statistics. Charts include up-to-date crash distributions by Delta-V and impact direction with corresponding injury severity rates. Rollover data is also analyzed, as well as historical trends for injury severity, belt usage, air bag availability, and the availability of vehicle safety technology.

Spine degeneration can lower injury tolerance and influence injury outcomes in vehicle crashes. To date, limited information exists on the effect of age and sex on thoracic spine 3-dimensional geometry. The purpose of this study is to quantify thoracic spinal column and canal geometry using selected geometrical measurement from a large sample of CT scans. More than 33,488 scans were obtained from the International Center for Automotive Medicine database at the University of Michigan under Institutional Review Board approval (HUM00041441). The sample consisted of CT scans obtained from 31,537 adult and 1,951 pediatric patients between the ages of 0 to 99 years old. Each scan was processed semi-automatically using custom algorithms written in MATLAB (The Math Works, Natick, MA). Five geometrical measurements were collected including: 1) maximum spinal curvature depth (D), 2) T1-to-T12 vertical height (H), 3) Kyphosis Index (KI), 4) kyphosis angle, and 5) spinal canal radius.

Advanced Driver Assistive System (ADAS) technologies have been introduced as the automotive industry moves towards autonomous driving. One ADAS technology with the potential for substantial safety benefits is forward collision warning and mitigation (FCWM), which is designed to warn drivers of imminent front-end collisions, potentiate driver braking responses, and apply the vehicle's brakes autonomously. Although the proliferation of FCWM technologies can, in many ways, mitigate the necessity of a timely braking response by a driver in an emergency situation, how these systems affect a driver's overall ability to safely, efficiently, and comfortably operate a motor vehicle remains unclear. Exponent conducted a closed-course evaluation of drivers' reactions to an imminent forward collision event while driving an FCWM-equipped vehicle, either with or without a secondary task administered through a hands-free cell phone.

Seat strength has increased over the past four decades which includes a transition to dual recliners. There are seat collision performance issues with stiff ABTS and very strong seats in rear impacts with different occupant sizes, seating positions and physical conditions. In this study, eight rear sled tests were conducted in four series: 1) ABTS in a 56 km/h (35 mph) test with a 50th Hybrid III ATD at MGA, 2) dual-recliner ABTS and F-150 in a 56 km/h (35 mph) test with a 5th female Hybrid III ATD at Ford, 3) dual-recliner ABTS in a 48 km/h (30 mph) test with a 95th Hybrid III ATD leaning inboard at CAPE and 4) dual-recliner ABTS and Escape in 40 km/h (25 mph) in-position and out-of-position tests with a 50th Hybrid III ATD at Ford. The sled tests showed that single-recliner ABTS seats twist in severe rear impacts with the pivot side deformed more rearward than the stanchion side.

Safety-critical systems in most modern applications are designed in a way such that they provide a fail-safe operation when a fault occurs, to pose minimum risk to the user. As these systems become more sophisticated with increased functionality, it is important that their design incorporates functional safety concepts which entail detection of a potential harmful condition that prompts a corrective action to prevent hazardous events. In this paper, we discuss the significance of safety-critical systems along with the implementation of fail-safe designs in these systems. We also aim to provide an overview of functional safety as addressed in some of the industry standards and through a case study demonstrate how the concepts can be used when developing a safety-critical system.

Lane Departure Warning (LDW) systems, along with other types of Advanced Driver Assistance Systems (ADAS), are becoming more common in passenger vehicles, with the general aim of improving driver safety through automation of various aspects of the driving task. Drivers have generally reported satisfaction with ADAS with the exception of LDW systems, which are often rated poorly or even deactivated by drivers. One potential contributor to this negative response may be an increase in the cognitive load associated with lane-keeping when LDW is in use. The present study sought to examine the relationship between LDW, lane-keeping behavior, and concurrent cognitive load, as measured by performance on a secondary task. Participants drove a vehicle equipped with LDW in a demarcated lane on a closed-course test track with and without the LDW system in use over multiple sessions.

The purpose of this research is to document representative examples of control inputs and body positioning experienced riders use to control a motorcycle through maneuvers representative of those encountered during real-world operation. There is limited publicly available data that tracks the magnitude or direction of steering head rotation, steering torque input, etc. used by a rider to initiate and exit a turn as well as maintaining directional control during maneuvers ranging from slow parking lot turns to high speed lane changes. Using Exponent’s Test and Engineering Center (TEC) track and skid pad, a course was defined that included several maneuvers at various speeds and radii. A previous paper [1] investigated the influence of rider kinematics (weight shift) on motorcycle control.

Through testing conducted by multiple facilities, it has been observed that the class of compact two-person vehicles designed exclusively for off-road operation known as Recreational Off-Highway Vehicles (ROVs) exhibit a range of steady-state handling characteristics - including both understeer and understeer transitioning to oversteer as measured in circle-turn tests similar to those set forth in SAEJ266. This handling characteristic is different from on-road passenger cars and light trucks which, under all but heavy loading conditions, exhibit linear range and limit understeer steady-state cornering behavior. Limit understeer is considered desirable for on-road vehicles because it provides a directionally stable and generally predictable control response. In the research presented in this paper, the handling qualities, including controllability, of a ROV which was modified to have different steady-state handling characteristics ranging from understeer to oversteer is examined.

The Society of Automotive Engineers Light Vehicle Exterior Sound Committee recognizes the value of preserving historical knowledge regarding the standards developed and reviewed by the committee. To memorialize the knowledge gained and lessons learned over the years, the current committee reached out to the chair of the committee during its formative years, Mr. Richard Schumacher, to discuss the rationale and reasoning for many of the early decisions made regarding vehicle sound standards. This work preserves those discussions and relates the history of some of the most commonly used sound level standards. In this paper and presentation, the formation of the committee is discussed, particularly in relation to EPA’s original concern with vehicle noise, as well as the alignment between SAE standards and ISO standards for vehicle noise measurements. The role of the committee is examined, and the review process for SAE vehicle sound standards is explained.

This study assesses vehicle and occupant responses in six vehicle-to-vehicle high-speed rear impact crash tests conducted at the Exponent Test and Engineering Center. The struck vehicle delta Vs ranged from 32 to 76 km/h and the vehicle centerline offsets varied from 5.7 to 114 cm. Five of the six tests were conducted with Hybrid III ATDs (Anthropometric Test Device) with two tests using the 50th male belted in the driver seat, one test with an unbelted 50th male in the driver seat, one test with a 95th male belted in the driver seat, and one with the 5th female lap belted in the left rear seat. All tests included vehicle instrumentation and three tests included ATD instrumentation. The ATD responses were analyzed and compared to corresponding IARVs (injury assessment reference values). Ground-based and onboard vehicle videos were synchronized with the vehicle kinematic data and biomechanical responses.

The energy dissipated by the fracture of wooden utility poles during vehicle impacts is not currently well documented, is dependent upon non-homogenous timber characteristics, and can therefore be difficult to quantify. While there is significant literature regarding the static and quasi-static properties of wood as a building material, there is a narrow body of literature regarding the viscoelastic properties of timber used for utility poles. Although some theoretical and small-scale testing research has been published, full-scale testing has not been conducted for the purpose of studying the vehicle-pole interaction during impacts. The parameters that define the severity of the impact include the acceleration profile, vehicle velocity change, and energy dissipation. Seven full-scale crash tests were conducted at Exponent's Arizona test facility utilizing both moving deformable and non-deformable barriers into new wooden utility poles.

Low-speed collisions between tractor-semitrailers and passenger vehicles may result in large areas of visible damage to the passenger vehicle, but often produce limited damage to the tractor-semitrailer. Despite this, such accidents may lead to assertions of serious injury to the tractor driver and/or sleeper compartment occupant. Research regarding the impact environment and resulting injury potential of the occupants during these types of impacts is limited. This research investigated driver and sleeper compartment occupant responses to relatively low-speed and low-acceleration impact events. Five crash tests involving impact between a tractor-semitrailer and a passenger car were conducted. The test vehicles were a van semitrailer pulled by a tractor and three identical mid-sized sedans. The occupants of the tractor included a human driver and an un-instrumented Hybrid III 50th-percentile-male anthropomorphic test device (ATD).