Search Results

This paper introduces for the first time a fully connectorized passive optical star for use with plastic optical fiber that addresses all automotive application requirements. A unique mixing element is presented that offers linear expandability, uniformity of insertion loss, and packaging flexibility. The star is constructed of all plastic molded components to make it low cost and produceable in high volume and is single-ended to facilitate vehicle integration. The star is connectorized to facilitate assembly into the vehicle power and signal distribution system.

A wet multi-plate clutch, designated as the “starting clutch”, is used to replace the torque converter in the automatic transmission in order to improve vehicle fuel economy. The transmission ratio spread must be increased to compensate for the torque multiplication of the torque converter and avoid penalizing the 0-60 mph acceleration performance. The main challenge of this concept is the control of the starting clutch to ensure acceptable vehicle drivability. This paper describes the system of a five-speed starting clutch automatic transmission vehicle and shows vehicle test results. Vehicle test data show that (i) the fuel economy benefit of the starting clutch is significant, and (ii) a starting clutch transmission can be designed to equal or better the 0-60 mph acceleration performance of a torque converter transmission by proper selection of the gear ratios.

USING a high-speed motion picture camera, flame photographs were taken of the combustion process associated with the starting of hot gasoline engines. Compression ignition at isolated points followed by normal combustion caused peak cylinder pressures to occur prior to top dead-center under some low-speed engine conditions. In addition, an abnormal combustion phenomenon was observed in the last part of the charge to burn. The reaction rate was appreciably faster than normal for the engine speed and much slower than is usually observed in knocking combustion at normal engine speeds.

THIS description of the hydraulic control used with the hydra-matic transmission reveals how the control operates to change ratios under power without direction from the driver. The control's pattern of automatic shifting for ordinary, high-range driving has been selected as the best compromise between top performance and low ratio of engine noise to wind noise. The control's low range shifts gears according to performance dictates alone, furnishing greater power for extreme conditions at low speeds and enabling the driver to use his engine as a brake on steep descents. Heart of the control system is a double hydraulic governor, sensitive both to car speed and throttle opening. THIS paper, as well as the two that follow, one by Messrs. Nutt and Smirl and the other by Mr. Kimberly, make up a symposium on automatic transmission components presented at the 1947 SAE Summer Meeting.

This paper describes an absolute stability analysis of idle speed control systems. Current idle speed control systems make use of both spark advance and the idle air actuator to control engine speed for improved response relative to variations in the target idle speed due to load disturbances. The control system at idle can be presented by a multiple input multiple output (MIMO) model [1]. Control system design is usually done based on linear or linearized models [2,3,4]. However idle speed control systems are nonlinear because of the saturation of the actuators. This paper describes an application of the absolute stability theory to idle speed control systems with saturation of actuators.

The development and application of a traction control Kodiak and GMC TopKick are explained. Most traction systems use engine management to enable traction control, while the adaptive braking system can provide traction assist for either gas or Diesel powered vehicles from 14,000 lbs. to 33,000 lbs. GVW. The performance driven criteria that established the design requirements and the development of a new product to meet these objectives are discussed. Both the vehicle manufacturer and the traction controller supplier provided these criteria. The basic ABS and traction control hydraulic schematics will be described as they apply to the vehicles. The results of the development program will be compared to the criteria used to establish the goals, and the benefits of the traction control system will be discussed.

The Alliance of Automotive Manufacturers (Alliance) has produced a document in which Principle 1.4 gives criteria and methods for calculating downvision angles to navigation and telematics displays in vehicles. This paper describes the details of the criteria and methods for determining compliance. Visual displays placed high in the vehicle instrument panel help drivers to use their peripheral vision to monitor the roadway for major developments, even during brief glances to the display. The Alliance has developed two criteria to define the maximum allowable downward viewing angle for displayed information in North American vehicles. One criterion is for use in two-dimensional Computer Aided Design (CAD) analyses, and one is for use in three-dimensional CAD analyses. Alliance Principle 1.4 is consistent with known driver performance research data, and known facts about the peripheral sensitivity of the human visual system.

Architecture exploration could benefit from some early results of a safety analysis process. Typically, classical system safety analysis techniques such as Fault tree analysis (FTA) are performed after the design is completed. We propose an approach for an early safety assessment to improve the design and also shorten the design cycle time. A quick assessment to determine the safety figure of merit of the intended architecture expressed as a parametric expression can be used to determine the overall acceptability of the architecture. The result from a quick assessment of the system safety could be used as a means to explore system trade-offs in reliability and redundancy at the highest design levels.

By-wire systems have the potential of augmenting the normal capabilities of human drivers as well as serving as enablers for emerging safety technologies. To achieve these features, these systems must be carefully designed, analyzed, and verified for safety because they are new, complex, and potentially exhibit new and different failure modes and effects. Duplication may be required to ensure that safety margins are met in the presence of faults. Full duplication of every system may not lead to a cost effective implementation, especially if multiple independent by-wire systems are placed on a single vehicle. Other architectural approaches for the integration of by-wire systems need to be considered and analyzed. These architectures should meet if not exceed the safety requirements while providing a more cost effective implementation than a fully duplicated architecture.

We investigate and analyze the concept of “shared redundancy” and its application to the design of architectures that integrate multiple safety/mission critical functions or subsystems. The analysis is based on considering different design alternatives with varying levels of physical redundancy of the components constituting the functions or subsystems. Under a set of assumptions, we show that the overall system reliability and availability in a shared redundancy based architecture can be improved without increasing the levels of physical redundancy for the components employed at the subsystem level. However, such an improvement will be limited by the component(s) with the minimal level of redundancy.

This paper describes the recent efforts on developing an automotive climate control system throughout integrating an electrically-controlled variable capacity scroll compressor with a fuzzy logic control-based refrigerant flow management. Applying electrically-controlled variable capacity compressor technology to climate control systems has a significant impact on improving vehicle fuel economy, achieving higher passenger comfort level, and extending air and refrigerant temperature controllability as well. In this regard, it is very important for automotive climate control engineers to layout a system-level temperature control strategy so that the operation of variable capacity compressor can be optimized through integrating the component control schemes into the system-level temperature control. Electronically controlled expansion devices have become widely available in automotive air conditioning (A/C) systems for the future vehicle applications(1, 2, 3 and 4).

TURBOGLIDE is the deluxe automatic transmission of the General Motors Chevrolet. One of its most important features is that its performance ratio is available at any throttle position, enabling control of torque ratio and engine output by the throttle pedal. The system includes a five-element torque converter, pump, three turbines, and the dual stator. The entire installed unit weighs 148 lb, a result of the general arrangement and the use of aluminum in the case and bell housing. The authors discuss the basic operating principle of the transmission, the arrangement, performance, torque distribution, control system, and valve body.

The purpose of the Cadillac DeVille Night Vision System is to provide drivers with visual information beyond with the range of their headlamps. It can also help drivers see beyond the glare of oncoming vehicle’s headlamps. With increased visual range the driver may have more time to react to potentially dangerous situations. The system consists of a thermal imaging camera, a head-up display, and image controls. The camera senses temperature differences of objects in the road scene ahead and creates a thermal image of the scene. The head-up display projects this image onto the windshield creating a virtual image that appears at the front edge of the vehicle’s hood just below the driver’s line of sight. This paper will describe the system requirements and parameters of the 2000 Cadillac DeVille Night Vision system.

We investigate and analyze the concept of “missed detection” and its application to the design of architectures that integrate multiple safety/mission critical functions. The analysis is based on considering different design alternatives with varying levels of missed fault detection of the components constituting the functions or subsystems. The overall system reliability and availability in a fault tolerant architecture relies as heavily on the ability to detect a fault as it does on being able to prevent a fault as one would attempt by having multiple levels of redundancy and/or improved reliability of the components in such an architecture. In short, the safety of a particular architecture depends not only on component reliability, and fault tolerance, expressed as redundancy, but also on fault detectability.

Allison Gas Turbine Division of General Motors is performing the first phase of a multiphase development project aimed at demonstrating an electric vehicle based on a proton exchange membrane (PEM) fuel cell. This work is sponsored by the Office of Transportation Technologies of the U.S. Department of Energy (DoE) through the DoE's Chicago Field Office (Contract No. DE-AC02-90CH10435). This work complements major efforts under way to produce electric vehicles for reducing pollution in key urban areas. Battery powered vehicles will initially satisfy niche markets where limited range vehicles can meet commuter needs. The PEM fuel cell/battery hybrid using methanol as fuel potentially offers an extremely attractive option to increasing the range, payload, and/or performance of battery powered vehicles.

Electro-Motive Division of GM jointly with HRL Laboratories have developed a software tool, called TechPro, which assists in troubleshooting of diesel locomotives. The tool has been tested extensively in the field for the last two years. It has improved significantly the quality of diagnosis of locomotives. The tool is based on Graphical Probabilistic Models and Case Data Bases. We will discuss the design of the tool, its performance and will show its relevance to diagnosis of automobiles.

Passive star networks have been shown to be the best architecture for high speed vehicle networks. This paper attempts to describe how problems in passive star networks can be diagnosed in the field. The potential physical layer failure modes for passive star networks are detailed, and a network test tool is described which is capable of determining whether a media fault exists and locating the position of that fault. The application of the test tool to potential failure modes is discussed.

Commercially available software tools are widely used to assist in conducting life cycle inventory, life cycle assessment (LCA), life cycle impact analysis (LCIA), and design for the environment (DfE) studies. Five leading software tools, Boustead 4.2, GaBi 3.2, SimaPro 4.0, TEAM 3.0, and Toolkit, currently in use or under consideration by life cycle practitioners, were selected for testing, and a detailed evaluation scheme was used to evaluate the effectiveness of these tools for practical application in automotive life cycle studies. A consensus numerical score for each of 20 separate test criteria was assigned to each of the software packages under evaluation, and the total scores compared. On the basis of these scores, the authors chose GaBi version 3.2 as the LCA software package currently best suited for use by experienced life cycle practitioners in conducting environmental life cycle assessments in the automotive industry.

It is known that the formability of tailored welded blanks depends on the welding set-up conditions. Little information is available on the correlation between the formability of welded blanks and weld set-up conditions. In this investigation, effects of mash seam welding parameters of weld current, weld force, material overlap and planish on formability performance of welded blanks are studied. The systematic design of experiments approach is used to identify the key weld parameters influencing the formability performance of welded blanks. It is found that high weld force decreases formability of welded blanks and high weld force coupled with a small material overlap results in very low forming limit of the weld zone. Weld current has little effect on formability of welded blanks and planishing significantly reduces it. Overall, the mash seam welded blanks produced with appropriate weld set-up conditions are robust with respect to formability.

A wet multi-plate clutch, designated as the “starting clutch”, and a two-speed simple planetary gearset are used to replace the torque converter in the 4T60-E automatic transmission in order to study the potential improvement of vehicle fuel economy without sacrificing 0 - 60 mph acceleration performance. The starting clutch and the two-speed simple planetary gearset are designed to fit in the torque converter compartment. This paper describes the modified five-speed 4T60-E starting clutch automatic transmission system and provides vehicle test results to demonstrate its fuel economy and 0-60 mph performance potential.