Search Results

Wheel rim is one of the most critical safety parts in a vehicle. Strength in cornering loading is one of the most important durability test requirements for automotive steel wheel rim apart from other loading conditions like vertical and impact loads. Based on the category of vehicle and customer usage pattern, the accelerated cornering test is derived for testing steel wheel rims. The simulation and certification of steel wheel rim for the required dynamic durability testing requirement involves many steps ranging from acceptance criteria derivation to reliably addressing known potential failure zones in steel wheel rims. Nave radius and crown are sensitive to cornering loads, given the pitch circle diameter at the concept stage, the known effects of these key parameters are determined from DOE and used as reliable indicators to arrive at the shape and section of the steel wheel rim.

One of the most essential components of automotive HVAC system is compressor. In a vehicle it is directly mounted on the engine. It derives power from the engine feed system to keep refrigerant moving in the HVAC system of the vehicle. It is also essential to complete the vapor compression cycle. During the operation, it causes considerable load on the engine and thus results in lower fuel efficiency and higher pollution. There are several types of compressors available globally. According to construction it can be classified as reciprocating piston type, scroll type and rotary vane type. The reciprocating piston types of compressors are further classified as fixed displacement and variable displacement. Normally the fixed displacement compressors have good idling cooling performance, but it increases the load on the engine. To reduce the load on the engine and to have good idling cooling performance, generally a variable displacement compressor is used.

The life of a two-wheeler and its parts depend much on its usage during its years of running. The quality of its parts determine the life and efficiency; however the handling of the two-wheeler also plays a major role in estimating it's life and other performance parameters. Hence, it is beneficial to have an efficient system which enhances the life of a two-wheeler and also gives better mileage. This paper constitutes an efficient drive pattern system which addresses the above. This system consists of two main parts: the data collection system and an Android-based mobile application which runs on a mobile phone. The data collection system collects data from various sensors on the vehicle and then the data is processed and sent to the mobile phone of the rider during the run time of the two-wheeler. The application uses this data to depict useful information like drive pattern and various indicators.

This paper describes application of Design of Experiments (DOE) technique and optimization for mass reduction of a Sports utility vehicle (SUV) body in white (BIW). Thickness of the body panels is taken as design variable for the study. The BIW global torsion, bending and front end modes are key indicators of the stiffness and mass of the structure. By considering the global modes the structural strength of the vehicle also gets accounted, since the vehicle is subjected to bending and twisting moments during proving ground test. The DOE is setup in a virtual environment and the results for different configurations are obtained through simulations. The results obtained from the DOE exercise are used to check the sensitivity of the panels. The panels are selected for mass reduction based on the analysis of the results. This final configuration is further evaluated for determining the stiffness and strength of the BIW.

Aerodynamic simulation using commercial CFD (Computational Fluid Dynamics) codes is now an integral part of the vehicle design process. Aerodynamic prediction and vehicle development program runs in parallel. This requires a good agreement between experimental measurements and CFD prediction of aerodynamic behavior of a vehicle. The comparison between experimental and simulation results show differences, as it may not be possible to replicate effect of all the wind tunnel parameters in the simulation. This paper presents the details of aerodynamic simulation process of a Crossover and its validation with the experimental results available from the wind tunnel tests. The results are compared for different configurations such as- closing the grille openings, removing the rearview mirror, adding ski-rack and using different tyres. This study also includes the effect of different wind speeds and yaw angles on the coefficient of drag.

In vehicle Front End Flow (FEF) analysis, the basic objective is to predict the mass flow/velocity of air at radiator inlet with constant fan rotation. In general, the Multiple Reference Frame (MRF) model is used to model the fan. The flow velocity distribution at radiator inlet due to fan rotation should be uniform in circumferential direction whereas, it should vary in radial direction depending upon the blade geometry. However, the drawback with MRF model is that, it gives higher velocities near radiator inlet at regions corresponding to the fan blades and lower velocities at other regions, which is not realistic. This issue is more predominant when the vehicle is at low speeds or when radiator is placed at mid or back of the vehicle or the fan is having less number of blades. In order to nullify this uneven velocity distribution at radiator inlet, Mixing Plane (MP) approach was used in addition to the MRF model.

In today's automotive industry Benchmarking plays a vital role to improve performance, quality of critical functions and key areas of an organization by understanding and evaluating the products & processes in relation to Best Practices. Gear Reverse Engineering (here in after called as GRE) a part of Benchmarking is an activity which follows an analytical approach to calculate basic key parameters for an unknown gear pair. This paper propose a diagnostic tool/method, which determines basic gear parameters for an unknown gear pair, by simply measuring few dimensions as input followed by step wise analytical approach. This tool/method simplifies the gear designer job at initial stage by eliminating frequent trial & errors, iterations and complex measurements, which saves time & cost.

As the world rapidly moves from IC engine powered vehicles to the ‘more sustainable’ electrified vehicles, the Powertrain Mounting System needs to be re-engineered to meet refinement requirements of customer. Electric vehicles are quieter but due to lack of the “masking effect”, are sensitive to minor disturbances that are perceived to be objectionable by passengers. Also, E-powertrains are lighter, produce higher torque at low rpms & operate at higher rpms which calls for different countermeasures for mounting systems compared to conventional single isolation 3-point mounting system as used in IC engines. Double isolation mounting system, where powertrain is connected to an auxiliary mass (sub frame/cradle) via mounts, which is suspended to the vehicle body via subframe bushes results in 12 rigid body modes, 6 for each mass, is highly effective in lowering the transmission of vibration at high frequencies.

Multidisciplinary Design Optimization (MDO) of an automobile body structure is a challenging task as it involves multiple, often conflicting requirements of safety, durability & NVH. Conventionally MDO process requires running large number of design of experiments (DOE) to explore the full design space and to build response surface for optimization. As the safety simulations are highly nonlinear in nature, they typically require significant amount of computational time and resources. Hence the conventional MDO approach is too expensive if too many design variables are simultaneously considered. In this paper, an alternative approach using Equivalent Static Load (ESL) method has been suggested for MDO which is quicker & accurate. The basic idea of the Equivalent Static Load-Method (ESL) is to divide the original nonlinear dynamic optimization problem into an iterative linear optimization and nonlinear analysis process.

Electric vehicles (EV) are much quieter than IC engine powered vehicles due to less mechanical components and absence of combustion. The lower cabin noise in electric vehicles make customers sensitive to even small noise disturbances in vehicle. Road boom noise is one of such major concerns to which the customers are sensitive in electric vehicles. The test vehicle is a front wheel driven compact SUV powered by electric motor. On normal plain road, noise levels are acceptable but when the vehicle has been driven on coarse road, the boom noise is perceived, and the levels are objectionable. Multi reference Transfer Path Analysis (MTPA) is conducted to identify the path through which maximum forces are entering the body. Based on MTPA, modifications are proposed on the suspension bushes and the noise levels were assessed.

The customer of today is sensitive towards shift quality. The demand is for a crisp and precise gear shift with low shift effort. The impulses from synchronizers make shifts feel notchy. After synchronization the blocker ring releases the sleeve. The sleeve then hits the teeth of the clutch body ring. The second impulse causes a phenomenon called double bump. This can be felt at the hand and makes a shift feel notchy or sluggish. An ideal way to overcome this is to optimize the detent profile. This paper explains in detail the various factors that contribute to the perceived shift feel. Various methods to optimize the forces on the knob by changing the detent profile are discussed. Gear Shift Quality Assessment (referred as GSQA henceforth) is a tool to acquire the required shift feel data. Using this tool shift efforts and kinematics of a 5 speed manual transmission are plotted for illustration. The calculations required to optimize the detent profile are explained in detail.

This work discusses about the emission development of a 4 cylinder inline 3.3 liter CRDe to meet BS III emission norms applicable to 3.5 Ton and above category and upgradable to BS IV emission by suitable after treatment. This engine is developed from a 3.2l mechanical pump engine. During development the focus was on the usage of higher swept volume, selection of engine hardware like piston bowl, turbocharger, injectors and optimization of the injection parameters. A cost-effective solution for meeting the BS III norms in the LCV category without application of EGR and exhaust after treatment even though there is 15% increase of the power rating and 10% increase in Peak torque of the engine. Injection parameters like injection timing, injection quantity and pilot injection were optimized to meet the emission target.

The development of interior fittings of passenger car to minimize the injuries to the head of the occupants requires mandatory compliance to the regulations in Europe and USA. In European regulation ECE R21 and similarly in FMVSS 201 the test on the instrument panel area suffices. The FMVSS 201u requirements in USA require also a free motion headform to be impacted on additional areas of the A-Pillar trim, sun visors, grab handles, and seat belt upper anchorage points of the B-Pillar too. Free Motion Headform Impactors (FMHI) are costly equipment. The FMVSS 201u [1] test is not conducted by any test agency in India as yet. Paper deals with the development of the head form impactor to fire the headform at angular positions in the vehicle and the test results have enabled the development of the vehicle interiors to enhance the safety of vehicles in crash situations.

The Valve Train system is an integral part of any engine and the impact of its design is very crucial, particularly in high speed engines. Maintaining the required valve timing throught the engine operating speed and longer component life are the two important parameters which drive current valvetrain designs. An engine ValveTrain system designed for a valve lift of 7mm is to be modified for an increased valve lift of 8mm. A study was conducted to understand which design parameters are to be changed /modified to make this possible. For this study, the valvetrain of an air-cooled motorcycle engine is taken up. The valvetrain arrangement was an Over Head Camshaft (OHC) design with a Roller-Follower. A 1D commercially available numerical code was used to simulate the kinematics and dynamics of the system.

This paper takes a review of fretting phenomenon on splines of the engaging gears and corresponding splines on shaft of automotive transmission and how it leads to failure of other components in the gearbox. Fretting is a special wear process which occurs at the contact area of two mating metal surfaces when subject to minute relative oscillating motion under vibration. In automotive gearbox, which is subjected to torsional vibrations of the powertrain, the splines of engaging gears and corresponding shaft may experience fretting, especially when the subject gear pair is not engaged. The wear debris formed under fretting process when oxidizes becomes very hard and more abrasive than base metal. These oxidized wear particles when comes in mesh contact with nearby components like bearings, gears etc. may damage these parts during operation and eventually lead to failure.

Customer comfort has been at the core of any vehicle design. A segment of vehicle wherein the provision given for roof to be removed to enhance the customer experience. A similar vehicle is the subject matter for the evaluation here. The vehicle being off-roader, customer buying such vehicles are passionate about these lifestyle vehicle’s performance aspects. The roof components are plastic and are bolted with the BIW structure with sealing in place at the interface. The windshield angle being close to vertical, there is a tendency for flow separation at the front tip of roof, while vehicle driven at speed. This creates significant pressure difference across the roof surface, leading to vertical deformation of roof between the bolted mounts. In case the magnitude of deformations not controlled, the reduced sealing effectiveness lets air gushing in the cabin and make noise which can be audible to customer.

In current competitive environment automobile industry is under heavy pressure to reduce time to market. First time right design is an important aspect to achieve the time and cost targets. CAE is a tool which helps designer to come up with first time right design. This also calls for high degree of confidence in CAE simulation results which can only be achieved by undertaking correlation exercises. In automobiles most of the structures are subjected to vibration from dynamic loads. All the dynamic road loads are random in nature and can be very easily expressed in terms of power spectral density functions. In the current scenario structural durability of the parts subjected to vibration is done partially through modal performance and partially though frequency response analysis. The only question that arises is what amplitude to use at what frequency and how to map all the accelerated tests dynamic load frequency spectrum to simulation domain.

Continually increasing customer demands and legislative Requirements regarding fuel economy, emissions, Performance, drive ability and comfort need to be met by every OEM's developing vehicles worldwide. There is a serious pressure to reduce CO2 emission from automotive application which contributes to around 15.9% of the total CO2 production based on the Surveys done time to time. In a developing market like India, many foreign players are entering with lots of option for offering to this market. The parameters of prime importance here are fuel efficiency with good drive ability and at the same time affordable price. Diesel engines are finding these benefits and attracting the buyer over its counterpart (Gasoline). The road condition and the driving pattern in India compared with developed countries differ to a major extent. In India, the Low speed uses are predominating in Cities and in Ghats.

Increased popularity on SUV category in the market has led to high focus on performance attributes of SUVs. Considering high weight & CoG achieving target handling performance is always a challenge. Static Wheel Alignment parameters, especially Camber have shown significant contribution in Handling attributes of vehicle. This paper presents an experimental study on change in wheel camber under the influence of different vehicle loading conditions. In SUVs, generally wheel is subjected to large deflection from its high static loads which makes it quite difficult to maintain an ideal camber angle. Hence, it is important to analyze the camber angle variations under actual loading conditions. An in-house fixture is developed to emulate the actual vehicle loading conditions at rear wheel end. The multi-link rigid axle suspension with watt’s link assembly is mounted on the chassis-frame which is rigidly fixed to ground, and loads are achieved through hydraulic actuators at Wheels.

The customer perception about the door slam noise and its feel would indicate the brand image of the car. In this paper the authors have made an effort to improve the door slam noise quality of the vehicle, which is currently in production. This paper describes the probable areas in the door to improve the slam noise quality by attempting modifications in the door design factors, such as door alignments, door panel stiffness, door trims, window glass rattle, latch striker alignment, door seals, air extractor. Since the door closing event is a transient phenomenon, it requires special tools such as wavelet transforms, Zwicker loudness to understand the slam events precisely. Subjective jury evaluations have been conducted to understand the effect of these modifications and rank the modifications based on their contributions to the door slam quality.