Search Results

The rapidly growing amount of software in cars reshapes the automotive industry. The software has a significant influence on the production lines, due to the time required to flash it onto the vehicle and its capabilities to test vehicle functions during production. In this paper we identify the main pain points regarding software in the manufacturing process by performing a structured analysis on the experiences made at a major car manufacturer over last two years. Consequently, the paper analyses the possible approaches to address the challenges.

The objective was to develop a modem engine to succeed the M 102; 2.6 million of these units were made between 1979 and today making it the most successful Mercedes-Benz four-cylinder petrol engine to date. The new M 111 coordinated production set-up together with the familiar M 104 six-cylinder four-valve engines and the 600 diesel series. Emphasis has been deliberately given to improved torque rather than very high volumetric efficiency. This has made it possible to apply four-valve technology, which was originally only to be found in motor racing, in such a way that ordinary customers can benefit form advantages such as high torque and raised power output, as well as reduced fuel consumption and emissions. Extensive noise-reducing measures in the engine ensure that, despite the higher power output and lower engine weight, noise levels have also been improved.

The settings of adaptive suspension elements may be switched from a comfortable “soft” characteristic to a safe and “firm” characteristic. Thus the possibility is given to not only improve the ride comfort, but the dynamic driving behavior as well, since no compromise must be made between these two criteria when tuning the suspensions. Such systems seem to be very promising for commercial vehicles, as - because of their changing loading conditions - it is very difficult to design an optimal suspension system using conventional springs and dampers. This paper describes the influence of shock absorbers and air springs with variable characteristics on the ride comfort and the dynamic behavior of a 15-t-truck by investigations done with a simulation system. A series production vehicle without adaptive suspension elements serves as basis. At first the results of measurements and simulations are compared and show a very good concurrence.

In this paper, the differences between a production car of the 2018 A-class and an early stage vehicle model with a mostly similar outer skin are examined experimentally and numerically. The aerodynamic development of vehicles at Mercedes-Benz is divided into several phases. When comparing force coefficients differences can be observed between these distinct hardware stages as well as when comparing steady state simulations to wind tunnel measurements. In early phases when prototype vehicles are not yet available, so-called aero foam models are used. These are well-defined full-sized vehicle models, as the outer skin is milled from Polyurethane. Important aerodynamic characteristics such as a motor compartment with a cooling module, deflecting axles with rotatable wheels and underbody covers are represented.

Over the last 40 years it has been possible to lengthen recommended passenger car engine oil drain intervals by up to five times, despite the substantial increases in oil stress through continously rising demands on performance and environmental acceptability. Behind this considerable progress lie improvements in engine design and production technology and the development of suitable advanced engine oil formulations. With increasing oil drain intervals comes a growing uncertainty as to exactly when the oil change should best be made: a fixed mileage applicable to all vehicles is preferred for its practicality but the optimum depends on the driving history of individual vehicles. In Europe a 15000 km oil drain interval is now normal. A further extension based on a fixed interval would give an advantage to a minority of customers but could seriously compromise the durability of engines in the overall vehicle population.

Car manufacturers spend steadily increasing efforts to design cars in such a way that material selection, production steps, use and recycling, respectively disposal, fulfill environmental expectations and requirements to an optimal, best known extent. The additional application of Life Cycle Assessment (LCA) for car design supports a better and virtually “objective” understanding about resource consumption and environmental impacts during the complete life cycle of cars. Thus, LCA opens a high potential to contribute for future cars to improve them in terms of ecology as well as with regard to technological and even economic aspects. Holistic Life Cycle Costing (LCC) can hereby serve in a useful complementary manner. Co-operating with experienced partners and taking part in the development of LCA standards, Mercedes-Benz is developing LCA as a supporting tool for vehicle design.

Meta material has been known for many years and the physics are well known since decades. But the challenge has always been to put the know how into (mass) production. This was the reason why no meta material has found its way into the automotive industry so far. But now things have changed: meta material became Meta Design and is going into serial production in 2024. Meta Design is a tunable spring mass system with foam acting as the spring and heavy layer as the mass. Meta Design is characterized by cavities in the foam and concentrated masses of the heavy layer as functionalized mass pins. By tuning the size of the cavities and the weight of the mass pins the acoustic performance can be adjusted to the requirements of each individual car line. After preliminary simulations, flat samples were tested in the lab. The next step was launched: the production and testing of a handmade prototype part of a firewall insulation for a Mercedes-Benz A-Class.