Search Results

This paper describes the Nippondenso in-line pump system designed for U.S. 1991 emissions regulation for medium duty diesel engines. With the combined use of the further improved in-line pump, NB-S and the multi-hole nozzle with a smaller orifice diameter, the required injection pressure of 100 MPa to 120 MPa at the nozzle can be achieved. However, some problems to be resolved exist in the subject fuel injection system: (1) secondary injection, (2) cavitation erosion of injection pipe, (3) higher pressure sealing of fuel, (4) undesirable fuel delivery curve vs. pump speed (called “Trumpet Shape” fuel delivery curve) Thus technical measures to cope with those problems are explained in details.

In recent years, diesel engine exhaust gas regulations become more severe due to environmental concerns. Especially, particulate reduction is one of the biggest concern, and the reduction through high injection pressure has been studied.(1), (2) and (3) However, much is not yet known about the influence of changes in fuel flow inside the nozzle tip on atomization and engine performance, and there would exist a lot of room for exhaust gas reduction through the nozzle modification. In this research we found that changing the shape of the nozzle tip showed a remarkable difference in the smoke emission at low engine speed, analysis showed that difference in the flow rate at the nozzle orifice cause difference in the fuel spray droplet size and therefore the difference in the smoke emission.

This paper reports on research conducted at Nippondenso Co., Ltd. and Meiji University on nozzles for heavy duty diesel engines. It focuses on fuel flow analysis in the nozzle, a key component of Fuel Injection Systems (FIS). The optimum design nozzle improves fuel flow and spray characteristics. A newer and tougher emission regulation from the EPA for heavy duty diesel engines will be inevitable from 1998 onward. The goal of every company is to design new FIS in advance which meet the regulations of the future rather than paying for expensive developing costs after new laws have come into effect. To meet the regulation, requirements for FIS are higher injection pressure and injection rate control which create better fuel spray atomization and higher utilization of air. In particular, the nozzle must ensure that high injection pressure is effectively converted to fuel spray without pressure losses.

The purpose of this paper is to discuss spray control of nozzle for heavy duty diesel engines. This paper will focus on fuel flow analysis of nozzle, key component of FIE (Fuel Injection Equipment). The optimum designed nozzle controls fuel flow and improves flow efficiency. FIE is required to produce higher injection pressure which creates better atomization and higher utilization of air. But the higher injection pressure results in increased pump driving torque, larger pump size and higher cost. To improve the fuel flow characteristic of nozzle, we analyzed it and developed a theoretical analysis method with computer model simulation to the optimum design nozzle. We also confirmed its effect by experiments.

The purpose of this paper is to discuss injection rate control of the nozzle for direct injection engines. This paper will focus on fuel flow analysis of the nozzle, a key component of Fuel Injection Systems (FIS). The optimum designed nozzle improves fuel flow efficiency and controls injection rate. To meet emission regulations in 1990's, FIS are required to produce higher injection pressure and injection rate control which creates better fuel spray atomization and higher utilization of air. But the higher injection pressure makes injection rate control difficult. In particular, injection rate control by needle lift traveling control is difficult because fuel flow characteristics in the nozzle change with injection pressure and needle lift. Furthermore, the forced control of needle lift results in poor fuel spray atomization.

The purpose of this study is to make clear the relationship between flow characteristics in the nozzle and injected spray characteristics. In this paper, we discuss the effect of the sac volume in the standard hole type nozzle on fuel flow and spray. The main object of this paper is to analyze fuel flow characteristics in the nozzle by using the enlarged model nozzles. Spray investigations confirmed that reducing the sac volume causes changes in the fuel injection direction at the initial stage of injection and in the spray penetration over consecutive injection. Flow investigations in the injection hole clarified that meandering the flow in the hole causes changes in the fuel injection direction. Flow investigations in the sac chamber clarified that separating the flow from the sac wall causes meandering the flow in the hole. Furthermore, the methods to restrain the flow in the sac chamber from separating from the sac wall were discussed.