Search Results

In this paper, we have analyzed the problem of the engine noise propagation and have classified that there is a fundamental relationship between exterior noise and structural design. In the case of light vehicles, we have isolated the following 2 factors in structural design which have a direct bearing on exterior noise. (1) The layout and the area of exposed openings in the engine room. (2) The ability of the engine room to absorb noise. In conclusion we suggest comprehensive approach to the problem of automotive noise reduction.

Research is under way on an engine system [1] that achieves a variable compression ratio using a multiple-link mechanism between the crankshaft and pistons for the dual purpose of improving fuel economy and power output. At present, there is no database that allows direct judgment of the feasibility of the specific sliding parts in this mechanism. In this paper, the feasibility was examined by making a comparison with the sliding characteristics and material properties of conventional engine parts, for which databases exist, and using evaluation parameters based on mixed elasto-hydrodynamic (EHD) lubrication calculations. In addition, the innovations made to the mixed EHD calculation method used in this study to facilitate calculations under various lubrication conditions are also explained, including the treatment of surface roughness, wear progress and stiffness around the bearings.

Maintaining reliability of the connecting rod bearing is a very important subject, and the following is a problem that needs to be overcome. Predicting reliability has generally depended on minimum oil film thickness (M.O.F.T), but recently, the engines of passenger cars which have greater power and speed potential than conventional ones are sometimes run beyond their M.O.F.T. limit (a degree of roughness around the crank shaft's axis.) In such a case, it is so difficult to predict reliability according to M.O.F.T., that we need a new index which directly shows seizure and wear. For this purpose, we found that the crank shaft pin temperature can be a key cause of seizure and wear according to an analysis of the relationship between its temperature and the seizure and wear caused intentionally. Using this method, we confirmed that the combination of bearing and crank shaft materials is very important for preventing seizure and wear.

There has been a growing need to develop more compact automatic transmissions with a greater number of speeds for better fuel economy and better driveability. This study investigated a method for determining suitable planetary gear trains for today's transmissions. A computer program has been developed for application to five-speed transmissions consisting of two planetary gearsets. By analyzing various gear train possibilities, the program can identify which gearsets are suitable for different conditions, including the number of speeds, the number of binding elements, topological suitability and other factors.

Sophisticated product designs enrich people's lives and social demands for creation of good designs are quite strong. In the automobile industry, good design quality is one of the principal factors for determining market competitiveness. In this situation where good design quality is required of every product, the authors have developed a CAD/CAM system which makes it possible to create good and accurate designs by translating designers' ideas directly and quickly into high quality CAD models, a capability that has long been desired. With this high performance system, freely formed curves and surfaces can be easily manipulated with a man-machine interface familiar to industrial designers accutomed to the conventional design process. The system also integrates photo-realistic rendering, stereography and NC milling machines for verifying differences between the realized shape and the image in the designer's mind.

Gasoline engines employ various mechanisms for improvement of fuel consumption and reduction of exhaust emissions to deal with environmental problems. Direct fuel injection is one such technology. This paper presents a new quasi-dimensional combustion model applicable to direct injection gasoline engine. The Model consists of author's original in-cylinder turbulence and mixture homogeneity sub model suitable for direct fuel injection conditions. Model validation results exhibit good agreement with experimental and 3D CFD data at steady state and transient operating conditions.

A robotic driver has been designed on the basis of an analysis of a human driver's action in following a given driving schedule. The self-learning algorithm enables the robot to learn the vehicle characteristics without human intervention. Based on learned relationships, the robotic driver can determine an appropriate accelerator position and execute other operations through sophisticated calculations using the future scheduled vehicle speed and vehicle characteristics data. Compensation is also provided to minimize vehicle speed error. The robotic driver can reproduce the same types of exhaust emission and fuel economy data obtained with human drivers with good repeatability. It doesn't require long preparation time. Thereby making it possible to reduce experimentation work in the vehicle development process while providing good accuracy and reliability.

This paper describes a study of drag reduction devices for production pick-up trucks with a body-on-frame structure using full-scale wind tunnel testing and Computational Fluid Dynamics (CFD) simulations. First, the flow structure around a pick-up truck was investigated and studied, focusing in particular on the flow structure between the cabin and tailgate. It was found that the flow structure around the tailgate was closely related to aerodynamic drag. A low drag flow structure was found by flow analysis, and the separation angle at the roof end was identified as being important to achieve the flow structure. While proceeding with the development of a new production model, a technical issue of the flow structure involving sensitivity to the vehicle velocity was identified in connection with optimization of the roof end shape. (1)A tailgate spoiler was examined for solving this issue.

The ways in which vehicles are used in the field are continually becoming more diverse. In order to provide the optimum solution with respect to performance and weight, it is necessary to be able to assure vehicle endurance reliability with a high degree of accuracy in relation to the manner of use in each market. This situation has increased the importance of accurately quantifying the ways in which vehicles are used in the field and of designing vehicles with sufficient endurance reliability to match the usage requirements. This report presents a “market model” by which the manner of usage in the field can be treated quantitatively using combinations of environmental factors that influence the road load, drive load and corrosion load, representing typical loads vehicles must withstand.

It is important to understand the influence of housing stiffness on bearing performance, particularly for the connecting rod bearings of automotive engines. It is known that the engine lubricant shows a piezoviscous characteristic whereby its viscosity changes under the influence of pressure. Engine bearings under a heavy load are apt to be influenced in this way. In this study, the effects of connecting rod stiffness and lubricant piezoviscosity on bearing performance were examined by elastohydrodynamic lubrication (EHL) analysis under conditions corresponding to the high-speed operation of an actual engine. The results indicated that under such heavy load conditions housing stiffness greatly affects friction loss because of lubricant piezoviscosity. It was also found that the piezoviscosity of the lubricant has a large effect on bearing performance, as does its viscosity under atmospheric pressure.

The possibility of predicting engine bearing durability by elastohydrodynamic lubrication (EHL) calculations was investigated with the aim of being able to improve durability efficiently without conducting numerous confirmation tests. This study focused on the connecting rod big-end bearing of an automotive engine. The mechanisms of wear and fatigue, which determine bearing durability, were estimated by comparing the results of EHL analysis and experimental data. This comparison showed the possibility of predicting the wear amount and the occurrence of fatigue by calculation.

There has been a growing need in recent years to further improve vehicle fuel efficiency and reduce CO2 emissions. JATCO began mass production of a transmission for rear-wheel-drive (RWD) hybrid vehicle with Nissan in 2010, which was followed by the development of a front-wheel-drive (FWD) hybrid system (JATCO CVT8 HYBRID) for use on a midsize SUV in the U.S. market. While various types of hybrid systems have been proposed, the FWD system adopts a one-motor two-clutch parallel hybrid topology which is also used on the RWD hybrid. This high-efficiency system incorporates a clutch for decoupling the transmission of power between the engine and the motor. The hybrid system was substantially downsized from that used on the RWD vehicle in order to mount it on the FWD vehicle. This paper describes various seal technologies developed for housing the dry multi-plate clutch inside the motor, which was a key packaging technology for achieving the FWD hybrid system.

This paper explains the specific measures taken to develop the body and underfloor of the newly developed Electric Vehicle for the purpose of reducing drag. Additionally, the headlamps and fenders were designed with innovative shapes to reduce wind noise that occurs near the outside mirrors. As a result of utilizing the aerodynamic advantages of an electric vehicle to maximum effect, The newly developed Electric Vehicle achieves a class-leading drag coefficient and interior quietness.

It is well known that the wheels and tires account for approximately 25% of the overall aerodynamic drag of a vehicle. This is because the contribution of the tires to aerodynamic drag stems from not only aerodynamic drag itself directly caused by exposure to the main flow (tire CD), but also from aerodynamic drag indirectly caused by the interference between tire wakes and the upper body flow (body CD). In the literature, as far as the authors are aware, there have been no reports that have included the following all four aspects at once: (1) CD sensitivity to detailed tire shape factors; (2) CD sensitivity differences due to different vehicle body types; (3) CD sensitivity for each aerodynamic drag component, i.e., tire CD and body CD; (4) Flow structure and mechanism contributing to each aerodynamic drag component. The purpose of this study was to clarify CD sensitivity to tire shape factors for tire CD and body CD considering two different vehicle body types, sedan and SUV.

Wheels play an important role in determining the aerodynamic drag of passenger vehicles. This is because the contribution of wheels to aerodynamic drag comes from not only the wheels themselves, but also from the interference effect between wheel wakes and the base wake. As far as the authors are aware, there have been no reports about aerodynamic drag sensitivity to wheel shape factors for different vehicle types and different exterior body shapes. The purpose of this study was to clarify CD sensitivity to wheel shape factors for a sedan and an SUV, including different rear fender shapes. Many different wheel configurations were investigated in terms of the CD, base pressure and flow fields in wind tunnel tests. Multiple regression analyses were conducted to clarify CD sensitivity to each wheel shape factor based on the test data. This study revealed high CD sensitivity factors for both the sedan and SUV.

An electric vehicle (EV) has less powertrain energy loss than an internal combustion engine vehicle (ICE), so its aerodynamic accounts have a larger portion of drag contribution of the total energy loss. This means that EV aerodynamic performance has a larger impact on the all-electric range (AER). Therefore, the target set for the aerodynamics development for a new EV hatchback was to improving AER for the customer’s benefit. To achieve lower aerodynamic drag than the previous model’s good aerodynamic performance, an ideal airflow wake structure was initially defined for the new EV hatchback that has a flat underbody with no exhaust system. Several important parameters were specified and proper numerical values for the ideal airflow were defined for them. As a result, the new EV hatchback achieves a 4% reduction in drag coefficient (CD) from the previous model.

A two-channel LDV system is used to obtain accurate airflow measurements around scale models of passenger cars in wind tunnel tests at the Nissan Research Center. A 2-watt argon-ion laser is employed as the light source. The main optical unit and probe head are connected by optical fibers. The probe head consists of a compact LDV probe with a beam expander and focusing lens with a long focal length can be easily traversed. A new type of signal processor, performing a digital autocorrelation function, is employed to process the Doppler signals. Mean airflow velocities and turbulence intensities are calculated by a micro computer to evaluate the flow fields. The results of preliminary experiments conducted with this system indicate that the system is not only capable of measuring the mean velocity components, including reverse flow, it can also provide accurate estimation of turbulence components.

Reduction of interior noise is an important factor in vehicle design and many experimental and theoretical studies have been carried out to find effective noise reduction techniques. Previously, we developed a Structural-Acoustic Uncoupled Program, ACOUST3, as a technique for estimating low-frequency noise in the vehicle interior. In the present work, ACOUST3 has been extended to construct an acoustic coupling analysis system, ASCA, which is used to calculate low-frequency noise, such as boom noise. In order to calculate low-frequency noise accurately, it is necessary to represent the vibration characteristics of the trimmed body as closely as possible. To do this, we built a trimmed body model, incorporating 22 trim parts, based on vibration test results, and found that the calculated results obtained with the model correlated well with experimental data.

Car rust has been a big problem. To improve the effectiveness of rustproofing, car materials and some methods are being developed. Sealing the seams of body panels is one important method. But the sealing operation is a difficult process and it is not easy to maintain quality standards for workmen and automatized systems. To overcome this problem, we developed an automatic robot sealing system with following features: 1. The system can be easily installed on an existing conveyor and follows the line conveyor in synchronization during sealing operation. 2. Small robots can cover wide area inside the vihecle. 3. New sealant supply controllers can regurate the supply rate in response to speed and motion of robots with a high accuracy. This system has already been installed in the Murayma plant and has proved successful in achieving a high quality sealing result.

An electronically controlled closed-loop carburetor system has been developed for production application in Datsun car models. Providing a means of complying with Japanese Emission Standards, this design features the electronic control of carburetor supplied fuel with significantly improved emission performance and fuel economy. Technological advances include the noteworthy compensation of oxygen sensor output variations and improved transient emission.