Search Results

The Nexus vehicle was designed and built for Transport Canada at the University of Saskatchewan to demonstrate that a safety compliant single passenger commuter vehicle could attain extremely low fuel consumption rates at modest highway speeds. Experimentally determined steady state fuel consumption rates of the Nexus prototype ranged from 1.6 L/100 km at 61 km/hr up to 2.8 L/100 km at 121 km/hr. Fuel consumption rates for the Society of Automotive Engineers (SAE) driving cycle tests were 4.5 L/100 km for the SAE Urban cycle and 2.0 L/100 km for the SAE Interstate 55 cycle. The efficiency of the power train was determined using a laboratory dynamometer, enabling the road test results to be compared to the results from an energy and performance simulation program. Predicted fuel economy was in good agreement with that determined experimentally. Widespread use of single passenger commuter vehicles would substantially reduce current transportation energy consumption.

A feedback controller bas been developed using robust control techniques to control the sound radiated from turbulent flow driven plates. The control design methodology uses frequency domain loop shaping techniques. System uncertainty, sound pressure level reductions, and actuator constraints are included in the design process. For the wind noise problem, weighting factors have been included to distinguish between the importance of modes that radiate sound and those that do not radiate. The wind noise controller has been implemented in the quiet wind tunnel facility at the Ray W. Herrick Laboratories at Purdue University. A multiple-input, multiple-output controller using accelerometer feedback and shaker control was able to achieve control up to 1000 Hz. Sound pressure level reductions of as much as 15 dB were achieved at the frequencies of the plates modes. Overall reductions over the 100-1000 Hz band were approximately 5 dB.

An experimental program was conducted to verify the reduction in fuel consumption achievable with aerodynamic improvements to intercity buses. Wind tunnel model tests were used to develop effective aerodynamic improvements and full-scale road tests to validate the results. Greyhound Lines coach models MC-7 and MC-8 were tested with head- and crosswinds. Aerodynamic drag of the MC-7 was reduced 17 percent at zero yaw. Drag of the MC-8 initially was higher; it was reduced 27 percent at zero yaw by the best fairing. Both low-drag configurations were less sensitive to crosswinds than the original models; significant drag reduction was maintained to 15 degrees yaw angle. Fuel consumption measurements made with aerodynamic fairings installed on an MC-7 showed that the low-drag bus used 11.7 percent less fuel at a steady 55 mph. The cost of the full-scale modifications was estimated at $ 1,500 each for a retrofit kit and no added cost to produce on new vehicles.

The mobility modeling technique is applied to the structure-borne noise path through a vehicle suspension. The model is developed using measured FRF data taken on the isolated components of the suspension and body structure of a midsize sedan. Several important modeling issues of suspensions are resolved. It was determined that multiple degrees of freedom are required to model the coupling at joints between the suspension and body structure. The investigation also demonstrated that bushings should not be included in the measurements used to develop these models and should be added later using simplified bushing parameters. The importance of transfer mobility information between the various suspension attachments was also investigated. The agreement between the mobility model predictions and the measured FRF data for the overall system is better than similar data published in the literature to date.

A unique concept for a multi-body test rig enabling the simulation of longitudinal, steering and vertical dynamics was developed at the Institute for Mechatronic Systems (IMS) at TU Darmstadt. A prototype of this IMS test rig is currently being built. In conjunction with the IMS test rig, the Vehicle Terrain Performance Laboratory (VTPL) at Virginia Tech further developed a full car, seven degree of freedom (7 DOF) simulation model capable of accurately reproducing measured displacement, pitch, and roll of the vehicle body due to terrain excitation. The results of the 7 DOF car model were used as the reference input to the multi-body IMS test rig model. The goal of the IMS/VTPL joint effort was to determine whether or not a controller for the IMS test rig vertical actuator could accurately reproduce wheel displacements due to different measured terrain constraints.

It is a time and cost consuming way to physically develop Hybrid Electric Vehicle (HEV) supervisor controller due to the increasing complexity of powertrain system. This study aims to investigate the HEV supervisor controller development process using dSPACE midsize Hardware in the Loop simulation system (HIL) for HEV powertrain control. The prototyping controller was developed on basis of MircoAutoBox II, and an HIL test bench was built on midsize HIL machine for the purpose of verification. The feasibility and capability of HIL were attested by the prototyping control strategy and fault modes simulation. The proposed approach was demonstrated its effectiveness and applicability to HEV supervisor controller development.

Two structure-borne and two airborne paths were measured on 99 “identical” Isuzu RODEOs and 57 “identical” Isuzu pickup trucks. Significant effort was made to control measurement variability but not environmental (climate) variations. A record was kept of the tests of a reference vehicle over the variation of environmental factors. The frequency response functions (FRFs) of the reference vehicle varied by approximately 2-4 dB over the frequency range 0-500 Hz for the structure-borne paths and over 0-1000 Hz for the airborne paths due to measurement and environmental variations. The FRFs of the fleet varied by as much as 5-10 dB over the same frequency range. In this paper, the vehicle tests are described. The reference and the fleet data are shown in raw form. Reduced data and implications of the results are also discussed.

The lack of effective and efficient communication between pilots and maintenance technicians has been recognized as a problem in general aviation by both members of the industry and academia. The goal of this paper is to provide an accounting of the impact that communication between maintenance technicians and pilots, or the lack thereof, can have upon both the bottom line and the experience of those who operate within the general aviation arena. The researchers interviewed and observed maintenance technicians and pilots in general aviation operations to identify what members on both sides of the communication process identified as being problematic and troubling. Several of the major barriers to communication, as well as several strategies to overcome those barriers, are discussed.

The relationship of slip resistance (or coefficient of friction) to safe climbing system maneuvers on high profile vehicles has become an issue because of its possible connection to falls of drivers. To partially address this issue, coefficients of friction were measured for seven of the more popular fabricated metal step materials. Evaluated on these steps were four types of shoe materials (crepe, leather, ribbed-rubber, and oil-resistant-rubber) and three types of contaminant conditions (dry, wet-water, and diesel fuel). The final factor evaluated was the direction of sole force application. Results showed that COF varied primarily as a function of sole material and the presence of contaminants. Unexpectedly, few effects were attributible to the metal step materials. Numerous statistical interactions suggested that adequate levels of COF are more likely to be attained by targeting control on shoe soles and contaminants rather than the choice of a particular step material.

Structural sound transmission through primary bulb (PB) sealing systems was investigated. A two-degrees-of-freedom analytical model was developed to predict the sound transmission characteristics of a PB seal assembly. Detailed sound transmission measurements were made for two different random excitations: acoustic and aerodynamic. A reverberation room method was first used, whereby a seal sample installed within a test fixture was excited by a diffuse sound field. A quiet flow facility was then used to create aerodynamic pressure fluctuations which acted as the excitation. The space-averaged input pressure within the pseudo door gap cavity and the sound pressure transmitted on the quiescent side of the seal were obtained in each case for different cavity dimensions, seal compression, and seal designs. The sound transmission predictions obtained from the lumped element model were found to be in reasonable agreement with measured values.

It is generally agreed that adequate resolution is required to reproduce the structure of spray and gas jets in numerical computations. It has not been clarified what this resolution should be although it would appear reasonable to assume that it should be such that the physical scales of the problem are resolved. In the case of a jet, this implies that near the orifice, the jet diameter has to be resolved since this is the appropriate length scale. It is shown in this work that if such a resolution is not used in computing transient jets, the structure of the jet is not reproduced with adequate accuracy. In fact, unexpected, erroneous and misleading dependence on ambient turbulence length and time scales will be predicted when the initial ambient turbulence diffusivity is small relative to the jet diffusivity. When the ambient turbulence diffusivity is of the same order as the jet diffusivity or greater, entrainment rates are significantly underpredicted.