Search Results

Car Periphery Supervision (CPS) systems comprise a family of automotive systems that are based on sensors installed around the vehicle to monitor its environment. The measurement and evaluation of sensor data enables the realization of several kinds of higher level applications such as parking assistance or blind spot detection. Although a lot of similarity can be identified among CPS applications, these systems are traditionally built separately. Usually, each single system is built with its own electronic control unit, and it is likely that the application software is bound to the controller's hardware. Current systems engineering therefore often leads to a large number of inflexible, dedicated systems in the automobile that together consume a large amount of power, weight, and installation space and produce high manufacturing and maintenance costs.

A new combustion pressure sensor (CPS) for advanced engine management is presented, which is designed to carry out the functions: misfire detection, knock control, ignition control, camshaft phase detection and engine roughness control. For small size and high accuracy at a reasonable cost the piezoresistive effect, which is realized within an integrated circuit device and delivers low impedance output signals, has been chosen. Due to the optimized sensor housing, membrane and force transfer design, the sensor shows little offset drift when affected by flame front and environmental thermal stress. This paper describes the CPS and its performance in comparison with a well-known highly accurate reference sensor.

Increasingly stringent tailpipe emissions regulations have prompted renewed interest in catalyst heating technology – where an integrated device supplies supplemental heat to accelerate catalyst ‘light-off’. Bosch and Boysen, following a collaborative multi-year effort, have developed a Rapid Catalyst Heating System (RCH) for gasoline-fueled applications. The RCH system provides upwards of 25 kW of thermal power, greatly enhancing catalyst performance and robustness. Additional benefits include reduction of precious metal loading (versus a ‘PGM-only’ approach) and avoidance of near-engine catalyst placement (limiting the need for enrichment strategies). The following paper provides a technical overview of the Bosch/Boysen (BOB) Rapid Catalyst Heating system – including a detailed review of the system’s architecture, key performance characteristics, and the associated impact on vehicle-level emissions.

The first generation of radar-sensor-based ACC-Systems will be available in 1998/1999 in Europe. As a first step high end car manufacturers will sell ACC as optional equipment in their top models for a significant add-on price. For this generation good performance was the most important development goal. For the future, however, small, highly integrated systems are needed which easily can be fitted into the body of small cars. High performance and low cost are essential to allow the car manufacturers to sell ACC as standard equipment. A first step in that direction is the “Sensor and Control Unit” developed by Bosch which integrates a FMCW-radar sensor and the ACC-controller in one housing. It is designed for easy manufacturing on existing equipment with standard processes. The design meets the requirements of an early phase with low production figures as well as a phase characterized by increasing numbers and decreasing prices.

In recognition of safety considerations, modern fuel tanks are frequently extremely irregular in shape. This places limits on the application of conventional potentiometric sensors. Required are more universal sensors without mechanically-moving parts. These sensors should also be characterized by especially good resolution and precision in the residual-quantity range, that is, the zero point precision should be of a high order. One type of metal rod can be bent into any of a variety of shapes to provide an effective means of monitoring the fuel level. In this metal rod, the propagation characteristics of a certain type of sound wave, known as bending waves, display major variations according to the level of the surrounding medium: The waves spread more rapidly through the exposed section of the rod than through the area which remains submerged. Thus the rod's characteristic oscillation frequency varies as a function of immersion depth.

Employing novel surface micromachining techniques, a highly miniaturized, robust device has been fabricated. The accelerometer fulfills all requirements of state-of-the-art airbag systems. The present paper reports on the manufacturing and assembly process as well as the performance of the sensor. The capacitive sensing element consists of a moveable proof mass of polysilicon on a single crystalline silicon substrate. A lateral acceleration displaces the proof mass and a capacitive signal is generated at a comb electrode configuration. An external IC circuit provides the signal evaluation and conditioning in a closed loop mode, resulting in low temperature dependency of sensor characteristics and a wide frequency response. The sensor is fabricated by standard IC processing steps combined with additional surface micromachining techniques. A special deposition process in an epitaxial reactor allows the fabrication of moveable masses of more than 10 µm thickness.

Pedestrian protection is an upcoming field for research and development. Active pedestrian protection is described from a system perspective. In this view, the development of an active pedestrian protection system is shown. First an overview on statistics and legal requirements is given and the system requirements are discussed. Sensor concepts and realizations are shown, also different test methods and results are explained. FE-simulations to complete and later replace additional tests are developed, after cross check with the experimental results. In combination with the shown actuator concept this leads to a full functioning active pedestrian protection system.

This paper is based on the experiences with Adaptive Cruise Control (ACC) systems at BOSCH. Necessary components (especially range sensor, curve sensors, actuators and display) are described, roughly specified, and their respective strength and weaknesses are addressed. The system overview contains the basic structure, the main control strategy and the concept for driver-ACC interaction. Afterwards the principal as well as the current technical limits of ACC systems are discussed. The consequences on traffic flow, safety and driver behavior are emphasized. As an outlook, development trends for extended functionality are given for the next generation of driver assistance systems.

This paper presents advanced planar ZrO2 oxygen sensors being developed at Robert Bosch using a modified tetragonal partially stabilized zirconia (TZP) with high ionic conductivity, high phase stability and high thermo-mechanical strength. Green tape technology combined with highly automated thickfilm techniques allows robust and cost effective manufacturing of those novel sensing elements. Standardization of assembling parts reduces the complexity of the assembly line even in the case of different sensing principles. The sensor family meets the new requirements of modern ULEV strategies like fast light off below 10 s and linear control capability as well as high quality assurance standards. High volume production will start in 1997 for European customers.

In conventional sensor systems, mechanical and electronic components are generally operating at separated locations. Smart sensors integrate mechanical and electronic elements to a single system, thus offering new facilities for a common error compensation. In this concept, a unit-specific temperature dependence and a non-linear characteristic curve of the mechanical sensor element can be tolerated, thus saving a lot of costs in the manufacturing process of the mechanical components. The behaviour of the mechanical sensor element is described by a two-dimensional sensor correction function: Given the output of the mechanical sensor element and a measured value for the temperature, the true measurement value can be calculated by an error correction unit. In this paper, different error correction methods are examined and evaluated which can be used for a wide range of sensor types. They are applied to the example of a short-circuit ring displacement sensor.

The present paper concentrates on the option of catalytic autothermal reforming of gasoline for fuel cell applications. Major parameters of this process are the “Steam to Carbon Ratio” S/C and the air to fuel ratio λ. Computations assuming thermodynamic equilibrium in the autothermal reactor outlet (ATR) were carried out to attain information about their proper choice, as failure in adjusting the parameters within narrow limits has severe consequences on the reforming process. In order to quantify velocity distribution just ahead the catalyst and to evaluate mixing uniformity we designed an ATR featuring an optical access: Thus flow visualization using PIV (Particle Image Velocimetry) and LIF (Laser Induced Fluorescence) technique is possible. Preliminary PIV-results are presented and compared with CFD computations (Computational Fluid D ynamics).

The selective catalytic reduction (SCR) based on urea-water-solution is an effective technique to reduce nitrogen oxides (NOx) emitted from diesel engines. A 3D numerical computer model of the injection of urea-water-solution and their interaction with the exhaust gas flow and exhaust tubing is developed to evaluate different configurations during the development process of such a DeNOx-system. The model accounts for all relevant processes appearing from the injection point to the entrance of the SCR-catalyst: momentum interaction between gas phase and droplets evaporation and thermolysis of droplets hydrolysis of isocyanic acid in gas phase heat transfer between wall and droplets spray/wall-interaction two-component wall film including interaction with gas phase and exhaust tube The single modeling steps are verified with visualizations, patternator measurements, phase-doppler-anemometer results and temperature measurements.

Current vehicle concepts necessitate the multiple measurement of several variables required by separate electronic systems in the motor vehicle. There is the need to make sensors bus capable by the incorporation of electronic components in new definition concepts, in other words to make them multiply usable. Such bus concepts are at the present time taking concrete shape. The step of introducing electronics - especially digital - to the measuring point may simultaneously be used to considerably improve utilization of the information content of sensor structures using means of indivdual, digital correction to a greater level than has until now been technically possible. There remains the demand for high stability and reproducibility of the sensor properties over time. These signal preprocessing and information condensation processes on the spot also satisfy the need to relieve the central control units.

Until now, the use of biometric systems has not been in the public eye. The high cost of sensors and processing has meant that biometrics was previously restricted to high security access, financial transaction and law enforcement applications. However, as a result of improvements in technology, biometric sensor price and reliability have achieved levels where biometrics is being seriously considered for automotive systems. This paper introduces the field of biometrics, the key terms and processes. Fingerprint Technology and Identification by Fingerprint are discussed, as are the use and applicability of biometrics in automotive applications, including Personal Profiling, Keyless Engine Start and vehicle access authorization. The key findings of investigations over the last years are discussed.

If a sensor shall be applied in motor vehicles, all the components of the sensor must fulfil special requirements. Particular attention must be paid to the installation of the sensitive element and to the adaptation to which the sensor is to be put. The objective of this paper is to illustrate these demands more closely using three different types of sensors as examples: a displacement sensor, a pressure sensor and an acceleration sensor.

A new mass air flow meter, using a sensor element based on micro silicon technology, is presented. The sensor is able to detect the amount and direction of air flow. It is located in an aerodynamic bypass, which acts as a nonlinear filter. This enables the mass air flow meter to correctly determine the air mass aspirated by a four cylinder engine, even in the case where, due to strong oscillations of the flow, timewise backflow occurs near the measuring position. Results of laboratory and engine tests will be presented.

The continuing increase in the performance of restraint systems has led to a drastic increase in the number of actuator devices. The individual wiring of the igniters becomes more and more problematic through the accompanied large number of plug connections and cables. Along with demands for weight and volume reduction, there are requirements for EMI and short circuit protection to eliminate erroneous deployment and misuse. As a solution, a new multi-protocol dual wire bus system is described that has the capability to supply energy and address multiple peripheral output stages to simultaneously fire any combination of actuators.

The continuously increasing performance of modern automotive microelectronics is leading to ever more complex open and closed-loop control functions. Rigid mechanical connections a broken down and electronics applied to make them controllable. Among the examples are camshaft control, or future systems for variable valve-lift control. In addition, the individual systems in the vehicle, such as engine management, transmission-shift control, and ABSR will be networked with one another. The result is a system alliance which communicates through a car-wide web. The major challenge posed by this development in the future, lies in still being able to reliably control the complexity of the system alliance from the point of view of reliability and safety. This means that the suitable sensor and actuator basis, together with an architecture having fixed configuration rulings and matching development methods, are indispensable.

A new air quality sensor for climate control in automobiles has been developed. The sensor is designed for use in air conditioning systems with an air intake flap and a charcoal filter. The main indicators for the detection of air pollution are CO and NOx. The sensor elements consist of a SnO2 layer made in thick film technology resulting in small sensor size and high sensitivity at reasonable cost. The sensor elements are packaged together with an evaluation circuit in a water resistant sensor housing for underhood installation. By means of specific dopants the sensor elements have been optimized in order to detect CO and NOx with very low cross-sensitivity. This paper describes the design and production of the sensor. The performance of the complete unit under typical field conditions is presented. The sensor is in serial production.

Passenger car DI Diesel engines need a flexible fuel injection system. Bosch develops a common rail system for this purpose. Besides variation of fuel quantity and start of injection, it permits to choosing freely injection pressure inthe rangeof 150 to 1400 barand injecting fuel in several portions. These new means will contribute to further improvements of DI engines concerning noise, exhaust emissions and engine torque.