Search Results

Handling performance of a vehicle is a key characteristic determining the response of vehicle under different operating scenarios. An insight into these vehicle-handling characteristics at early stage can be extremely useful in the design and development process. Tire characterization and tuning is important and mandatory to scrutinize each functional and individual parameter of tire. Tire force and moment data is having a significant effect in vehicle handling. Segregation of tire parameter, which is contributing vehicle-handling performance, helps to identify and perform optimization for improvisation. The main objective of this study is development and integration optimized 1D tire model into multibody dynamics model of the vehicle to observe various vehicle compliances towards its handling performance target.

The automotive engineering fraternity is facing tremendous challenges to improve fuel economy and emissions of the internal combustion engine. The stringent CAFÉ standards for CO2 emissions are expected to become further demanding as time progresses. Indian OEM engineering experts have been considering various technology options to improve vehicle fuel economy. However, the time and costs associated with the development of these strategies and technologies remains a point of major concern and challenge. The potential of a technology to reduce fuel consumption can be estimated in three basic ways. One approach involves developing an actual prototype engine and vehicle with the technologies under evaluation, performing the actual measurements. Some variability from test to test is although expected, this method is the most accurate but time consuming and very expensive.

Vehicles have a wide range of resonance band due to design nature & characteristics of its aggregates. First order, vehicle speed dependent, wheel disturbance due to wheel imbalances can result in excitation of different vehicle aggregates. Steering wobble refers specifically to first order road wheel excitation effects, in frequency range of 10-16 Hz, that manifest themselves as significant steering wheel torsional vibrations at highway speeds i.e. at the range of 80 km/h to 120 km/h on smooth roads. The tire, being an elastic body analogous to an array of radial springs, may exhibit variations in stiffness about its circumference; hence, it may vibrate at different frequencies due to wheel imbalance. This paper introduces dynamic steering wobble analysis methodology either using vehicle speed at Discrete (individual speeds) or by Sweep (low to high speed) method to investigate steering wobble in the virtual environment using the full vehicle MBD model.

With India achieving the BSVI milestone, the diesel particulate filter (DPF) has become an imperative component of a modern diesel engine. A DPF system is a device designed to trap soot from exhaust gas of the diesel engine and demands periodic regeneration events to oxidize the accumulated soot particles. The regeneration event is triggered either based on the soot mass limit of the filter or the delta pressure across it. For a Heavy Duty Diesel Engine (HDDE), pressure difference across the DPF is not usually reliable as the size of the DPF is large enough compared to the DPF used ina passenger vehicle diesel engine. Also, the pressure difference across DPF is a function of exhaust mass flow and thus it makes it difficult to make an accurate call for active regeneration. This demands for a very accurate soot estimation model and it plays a vital role in a successful regeneration event.

Electric vehicles are fast expanding in market size, and there are increasing customer expectations on all aspects of the vehicle, including its noise and vibrational characteristics. Irritable noise from traction motors account for around 15% of the overall noise in an electric vehicle, and thus, has a need to be analysed and studied. This study focuses on identifying the critical vibro - acoustic orders for an 8 pole PMSM (Permanent Magnet Synchronous Motor) for three cases - healthy, with static eccentricity and with dynamic eccentricity. PMSM motors are widely used for traction and other applications due to their higher power density along with compact size. A coupled approach between electromagnetic and vibro - acoustic simulation is deployed to characterise the NVH behaviour of the motor.

Spot-weld joinery plays a major role in maintaining structural integrity of vehicle during an accident scenario. Robust failure definitions are important for accurate prediction of spot-weld failure in crash safety simulations. Spot welds have a complex metallurgical structure, consisting of fusion and heat affected zones. Identifying material failure definitions for huge number of spot-weld joint combinations in a typical Body in White (BIW) of a vehicle is highly challenging. In conventional LS-DYNA-MAT100 material model, spot-weld failure prediction accuracy is limited under complex crash loading scenarios, especially angular and bending load conditions. In order to enhance the failure predictions, a novel mathematical failure model is developed by considering instantaneous resultant loading along with bending moment as a key failure parameter to determine spot weld joint failure.

Nowadays, E- commerce and logistics business model is booming in India with road transport as a major mode of delivery system using containers. As competition in such business are on rise, different ways of improving profit margins are being continuously evolved. One such scenario is to look at reducing transportation cost while reducing fuel consumption. Traditionally, aero dynamics of commercial vehicles have never been in focus during their product development although literature shows major part of total fuel energy is consumed in overcoming aerodynamic drag at and above 60 kmph in case of large commercial vehicle. Hence improving vehicle exterior aerodynamic performance gives opportunity to reduce fuel consumption and thereby business profitability. Also byproduct of this improvement is reduced emissions and meeting regulatory requirements.

To cope up with the market requirements, OEMs need to react fast and develop advanced and highly refined vehicles keeping in mind multiple factors and Perceived Quality is one of the most important amongst those. Annoying squeak and rattle noises from the vehicle, whether it is new or used car, is the most customer irritant factor; which needs to be addressed in the vehicle development program. BSR (Buzz, Squeak and Rattle) and NVH (Noise, Vibrations and Harshness) performance is the critical in providing quieter experience to the customer and it is becoming more and more important due to transformation from ICE (Internal Combustion Engine) to Hybrid and Electric Powertrains. Among BSR noises, body squeak and creak is the most annoying and difficult to detect and correct, if reported on the prototype test or customer cars. Whereas, squeak and rattles from body fitment and underbody aggregates are relatively easy to address and correct.

Vehicles subjected to Indian duty cycles have to undergo extreme environments & road terrains, stone chipping. Underbody wear from this is one of the most significant forms of deleterious corrosion. Automobile companies deal with this by going for exotic & expensive underbody coating, which compositionally are "Polyvinyl Plastisol also popularly known as Poly Vinyl Chloride (PVC)". Across automotive industry, the stone chipping is prevented via applying PVC-coating to the extent of 800-1000 microns. The application of PVC-material throughout the vehicle underbody will add approximately 8-12 Kgs of weight. Our objective was to reduce the weight of applied PVC-material.

In previous work, AC Compressor Cycling (ACC) was modeled by incorporating evaporator thermal inertia in Mobile Air Conditioning (MAC) performance simulation. Prediction accuracy of >95% in average cabin air temperature has been achieved at moderate ambient condition, however the number of ACC events in 1D CAE simulation were higher as compared to physical test [1]. This paper documents the systematic approach followed to address the challenges in simulation model in order to bridge the gap between physical and digital. In physical phenomenon, during cabin cooldown, after meeting the set/ target cooling of a cabin, the ACC takes place. During ACC, gradual heat transfer takes place between cold evaporator surface and air flowing over it because of evaporator thermal inertia.

This paper documents the approach followed to simulate the physical phenomenon of thermistor based AC compressor Cut-OFF/Cut-IN (AC compressor cycling) in 1-Dimensional Computer Aided Engineering (1D CAE) to enable Mobile Air Conditioning (MAC) performance prediction at different ambient conditions. Thermistor based AC compressor cycling logic is incorporated in MAC systems to prevent ice formation at evaporator core and liquid refrigerant flow to AC compressor. Currently, during MAC system performance simulation over a transient drive cycle, the 1D models are able to predict cabin cooldown performance for severe ambient conditions (>40°C, high solar load) with >95% accuracy, as in these cases AC compressor cycling due to thermistor doesn’t occur at higher ambient.

Self-soiling or surface contamination is usual phenomenon observed during rainy season wherein dirt on road are picked by rotating wheel and later released in air as fine particles. These released dirt particles are further carried by airflow around vehicle and as a result stick on vehicle exterior surfaces leading to surface contamination. Surface dirt contamination is one of critical issues that need consideration during early phase of vehicle development as vehicle styling plays a critical role for airflow around vehicle and therefore settling of dirt on vehicle exterior surfaces. Non consideration of such aspects in design can lead to safety issues with likely non-functioning of parking sensors, camera and visibility issues through ORVM, tailgate glass etc. Hence it is important to understand physical as well as digital techniques for assessment of vehicle for surface dirt contamination.

The future of bus transit in new millennium is promising. This optimism is based on an anticipated long-term slowdown in growth of suburbs and revitalization of central cities. It reflects and escalates the public concern with traffic congestion, sprawl and pollution. This calls for double the use of public transport to address above issues. It calls for changing the mind-set of society towards public transports like buses, coaches etc. This could happen if bus design ensures right comfort, safety and TCO by ensuring refined bus transport. Hence, it is responsibility of OEMs to provide the new generation buses and coaches, which will ensure the public demands of comforts in terms of NVH refinement. This paper covers the unique approach used to convert the existing bus NVH refinement to next level as a short-term solution and with the intention of articulating NVH strategies for new generation bus development.

In recent years, there has been a rapid growing demand for laser brazing in the transportation industry for automotive-Body in White (BIW), steel sheet assembly. Implementation of laser brazing is aimed primarily to improve productivity, quality of joints and cost. Laser brazing works by filling the opening amongst two substrates by melting the filler wire with the help of laser beam (used as a heat source), whereas in conventional resistance spot welding, contacting metal surface points are joined by the heat obtained from resistance to electric current. BIW is essentially a welded metal structure which is meant to provide durability and crashworthiness to the vehicle and is conventionally assembled using resistance spot welding process. The BIW structure comprises of various steel grades having varying thicknesses, compositions, microstructures and mechanical properties.

Leaf springs are used for vehicle suspension to support the load. These springs are made of flat sections of spring steel in single or in stack of multiple layers, held together in bracketed assembly. The key characteristics of leaf spring are defined as ability to distribute stresses along its length and transmit a load over the width of the chassis structures. The most common leaf spring steels are carbon steels alloyed with Cr and micro-alloyed with Ti, V and Nb. The specific thermomechanical process and alloying elements result in specific strength and fatigue properties for spring steels. The unique properties which facilitate use of spring steel in leaf spring suspensions are ability to withstand considerable twisting or bending forces without any distortion. The microstructure of these steel determines the performance and reflects the process of steel manufacturing. The performance is mainly determined by evaluating fatigue life durability.

This paper is an application of ISO 26262 functional safety standards for fail-safe design, development and validation of Electric Power Assisted Steering (EPAS) System. As part of safety feature to save lives, prevent injuries and reduce economic loss due to accidents, many research institutes are working to ensure the safety and reliability of emerging safety-critical Electronic Control Systems in automobile applications. As, Advanced Driver Assistance Systems (ADAS) and other emerging technologies are introduced in the automobile application, the overall safety of these advanced electronic systems relies on the vehicle safety systems, such as steering systems. This paper outlines the approach of performing the Hazard Analysis & Risk Assessment (HARA) and developing a Functional Safety Concept. This approach incorporates several analysis methods, including Hazard and Operability study, Functional Failure Modes and Effects Analysis.

With the introduction of Connected Vehicles, it is possible to extend the limited horizon of vehicles on the road by collective perceptions, where vehicles periodically share their information with other vehicles and servers using cloud. Nevertheless, by the time the connected vehicle spread expands, it is critical to understand the validation techniques which can be used to ensure a flawless transfer of data and connectivity. Connected vehicles are mainly characterized by the smartphone application which is provided to the end customers to access the connectivity features in the vehicle. The end result which is delivered to the customer is through the integrated telematics unit in the vehicle which communicates through a communication layer with the cloud platform. The cloud server in turn interacts with the final application layer of the mobile application given to the customer.

The small commercial vehicle business is driven by demand in logistic, last mile transportation and white goods market. And to cater these businesses operational and safety needs, they require closed container on vehicle. As of now, very few OEM’s provide regulatory certified container vehicle because of constrains to meet inertia class of the vehicle. This paper focuses on design of a durable and extremely reliable container, made of the low-cost economy class glass fibre & core material. The present work provides the means to design the composite container for the N1 category of the vehicle. The weight of after-market metal container ranges between 300-350 Kg for this category of vehicle, which affects the overall fuel economy and emission of the vehicle. A detailed CAE analysis is done to design composite container suitable to meet inertia class targets and to achieve weight reduction of 30-40% as compared to metal container.

Hybridization with engine downsizing is a regular trend to achieve fuel economy benefits. However this leads to a development of new downsized engine which is very costly and time consuming process, also engine downsizing demands for expensive higher power electric system to meet performance targets. Various techniques like gear ratio optimization, reducing number of gears, battery size and control functionalities optimization have been evaluated for maximum fuel economy keeping system cost very low and improving vehicle performance. With optimized gear ratios and reduced number of gears for parallel hybrid, it is possible to operate the engine in the best efficiency zones without downsizing. Motor is selected based on power to weight ratio, gradient requirements, improved acceleration performance and top speed requirement of vehicle in EV mode.

Brake system design is intended to reduce vehicle speed in a very short time by ensuring vehicle safety. In the event of successive braking, brake system absorbs most of vehicle’s kinetic energy in the form of heat energy, at the same time it dissipates heat energy to the surrounding. During this short span of time, brake disc surface and rotor attains the highest temperatures which may cross their material allowable temperature limit or functional requirement. High temperatures on rotor disc affects durability & thermal reliability of the brake rotor. Excessive temperature on brake rotors can induce brake fade, disc coning which may result in reduced braking efficiency. To address the complex heat transfer and highly transient phenomenon during successive braking, numerical simulations can give more advantage than physical trials which helps to analyze complex 3D flow physics and heat dissipation from rotors in the vicinity of brake system.