Search Results

Fuel cells plays significant role in the automotive sector to substitute the fossil fuels and complement to electric vehicles. In the fuel cell vehicles fuel cell stack is major component. It is important to have a robust fuel cell model that can simulate the behaviour of the fuel cell stack under various operating conditions in order to study the functioning of a fuel cell and optimize its operating parameters and achieve the best efficiency in operation. The operating voltage of the fuel cell at different current densities depends upon thermodynamic parameters like temperature and pressure of the reactants as well factors like the state of humidification of the electrolyte membrane. A 1D model is developed to capture the variation in voltage at different current densities due to internal losses and changes to operating conditions like temperature and pressure.

In recent years due to significant increased cost of raw material, fuel and energy, vehicle cost is increased. As vehicle cost is one of the major factors that attracts prospective buyers, it has created specific demand for low weight and low-cost components than traditional components with better performance to meet customer expectations. Suspension is one of the critical aggregates where lot of material is used and reduction in weight tends to give lot of cost benefit. As suspension system derives vehicle’s handling performance, it has to be ensured that handling performance of vehicle is maintained the same or made better while reducing weight of the suspension. Advancements in simulation capabilities coupled with manufacturing technology has enabled development non-traditional leaf springs. One of such springs is mono-leaf spring without shackle. This type of leaf spring provides advantages such as low weight and nonlinear stiffness.

Electric vehicles are fast expanding in market size, and there are increasing customer expectations on all aspects of the vehicle, including its noise and vibrational characteristics. Irritable noise from traction motors account for around 15% of the overall noise in an electric vehicle, and thus, has a need to be analysed and studied. This study focuses on identifying the critical vibro - acoustic orders for an 8 pole PMSM (Permanent Magnet Synchronous Motor) for three cases - healthy, with static eccentricity and with dynamic eccentricity. PMSM motors are widely used for traction and other applications due to their higher power density along with compact size. A coupled approach between electromagnetic and vibro - acoustic simulation is deployed to characterise the NVH behaviour of the motor.

Nowadays, E- commerce and logistics business model is booming in India with road transport as a major mode of delivery system using containers. As competition in such business are on rise, different ways of improving profit margins are being continuously evolved. One such scenario is to look at reducing transportation cost while reducing fuel consumption. Traditionally, aero dynamics of commercial vehicles have never been in focus during their product development although literature shows major part of total fuel energy is consumed in overcoming aerodynamic drag at and above 60 kmph in case of large commercial vehicle. Hence improving vehicle exterior aerodynamic performance gives opportunity to reduce fuel consumption and thereby business profitability. Also byproduct of this improvement is reduced emissions and meeting regulatory requirements.

In regions like Indian Subcontinent, Gulf or Saharan & Sub-Saharan Africa, where the sunshine is abundant almost all year round, air-conditioning is an important aspect of vehicles (passenger cars, buses etc.). Higher heat means higher cooling demand which in turn means bigger AC system. Like other auxiliaries, AC compressor is a parasitic load on the engine. The best way to beat heat and reduce cabin heat load is to stop heat build-up itself. The present paper explores one such means of reducing cabin heat build-up by leveraging latent heat properties of phase change materials and thus improving the air condition performance. With the help of a case study this paper aims at detailing comprehensive effect of phase change material (PCM) and its application on the heat build-up inside the cabin of a vehicle, the air conditioning cooling performance, the time required to achieve comfort temperature, work of compression performed by AC compressor and COP.

The future of bus transit in new millennium is promising. This optimism is based on an anticipated long-term slowdown in growth of suburbs and revitalization of central cities. It reflects and escalates the public concern with traffic congestion, sprawl and pollution. This calls for double the use of public transport to address above issues. It calls for changing the mind-set of society towards public transports like buses, coaches etc. This could happen if bus design ensures right comfort, safety and TCO by ensuring refined bus transport. Hence, it is responsibility of OEMs to provide the new generation buses and coaches, which will ensure the public demands of comforts in terms of NVH refinement. This paper covers the unique approach used to convert the existing bus NVH refinement to next level as a short-term solution and with the intention of articulating NVH strategies for new generation bus development.

Methane (CH4) is main constituent of compressed natural gas (CNG). CNG is compressed to less than 1% of the volume, which it occupies at atmospheric pressure. CNG contains almost 70% to 90% methane, one of the most significant greenhouse gas contributing directly into climate change. The effects caused due to gas leakages that results in fire and bursting of cylinder can be prevented by continuous monitoring of gas leakage in the Gas transmission pipeline of the commercial vehicles. In order to detect the methane leaks and resolve as early as possible, effective sensors need to be researched, analyzed and developed. This paper discusses about the usage of sensor with digital output replacing the previous gas leak detection sensor module, which gives analog output. The previously used Gas leakage detection module implements a design of a gas leakage detector system with, LED and audio indication that notifies the leakage in gas to the users.

Leaf springs are used for vehicle suspension to support the load. These springs are made of flat sections of spring steel in single or in stack of multiple layers, held together in bracketed assembly. The key characteristics of leaf spring are defined as ability to distribute stresses along its length and transmit a load over the width of the chassis structures. The most common leaf spring steels are carbon steels alloyed with Cr and micro-alloyed with Ti, V and Nb. The specific thermomechanical process and alloying elements result in specific strength and fatigue properties for spring steels. The unique properties which facilitate use of spring steel in leaf spring suspensions are ability to withstand considerable twisting or bending forces without any distortion. The microstructure of these steel determines the performance and reflects the process of steel manufacturing. The performance is mainly determined by evaluating fatigue life durability.

With the introduction of Connected Vehicles, it is possible to extend the limited horizon of vehicles on the road by collective perceptions, where vehicles periodically share their information with other vehicles and servers using cloud. Nevertheless, by the time the connected vehicle spread expands, it is critical to understand the validation techniques which can be used to ensure a flawless transfer of data and connectivity. Connected vehicles are mainly characterized by the smartphone application which is provided to the end customers to access the connectivity features in the vehicle. The end result which is delivered to the customer is through the integrated telematics unit in the vehicle which communicates through a communication layer with the cloud platform. The cloud server in turn interacts with the final application layer of the mobile application given to the customer.

The small commercial vehicle business is driven by demand in logistic, last mile transportation and white goods market. And to cater these businesses operational and safety needs, they require closed container on vehicle. As of now, very few OEM’s provide regulatory certified container vehicle because of constrains to meet inertia class of the vehicle. This paper focuses on design of a durable and extremely reliable container, made of the low-cost economy class glass fibre & core material. The present work provides the means to design the composite container for the N1 category of the vehicle. The weight of after-market metal container ranges between 300-350 Kg for this category of vehicle, which affects the overall fuel economy and emission of the vehicle. A detailed CAE analysis is done to design composite container suitable to meet inertia class targets and to achieve weight reduction of 30-40% as compared to metal container.

Hybridization with engine downsizing is a regular trend to achieve fuel economy benefits. However this leads to a development of new downsized engine which is very costly and time consuming process, also engine downsizing demands for expensive higher power electric system to meet performance targets. Various techniques like gear ratio optimization, reducing number of gears, battery size and control functionalities optimization have been evaluated for maximum fuel economy keeping system cost very low and improving vehicle performance. With optimized gear ratios and reduced number of gears for parallel hybrid, it is possible to operate the engine in the best efficiency zones without downsizing. Motor is selected based on power to weight ratio, gradient requirements, improved acceleration performance and top speed requirement of vehicle in EV mode.

Shock loads/Jerk is a major cause of gearbox failure which occurs during abusive driving condition. In passenger car torque spikes are experienced by the transmission during launch/sudden clutch release events on flat road or off-road. Whereas, in case of commercial vehicle torque spikes are generated while operation in mines and off-road application especially in tipper vehicles. Torque spikes experienced by the gearbox can lead to gear failure, gear slippage and structural failure of housing. Research has been done till now to improve the design of gearbox to address such failures. However, with increased focus on transmission downsizing and improved vehicle performance (by weight reduction and more powerful engine) it is necessary to have optimum design to meet transmission life. This paper discuss the test setup and methodology used to simulate the torque spikes on test bench. To develop the test procedure huge data was collected on commercial vehicles.

In a current competitive automotive market, weight and cost optimization is the need of an hour. Therefore it is important to explore use of alternative material which has less weight, low manufacturing cost and better strength. This paper presents methodology to achieve cost & weight reduction through use of Austempered Ductile Iron (ADI) instead of alloy forging. ADI casting has lower density, physical properties at par with alloy forgings and lower manufacturing cost. Pivot arm is the one of the critical component of twin axle steering system which transfers the hydraulic torque from steering gearbox to second forward axle via linkage system. In order to design lightweight pivot arm, existing chromium alloy steel material is replaced with the Austempered ductile iron (ADI). Pivot arm is designed and validated digitally as well as bench test and results are found to be meeting cost and weight targets.

Designing a cabin tilting system for Light Commercial Vehicles using a single torsion bar becomes challenging considering the operator safety and stringent design weight targets. Performance of a good tilting system entirely depends on cabin mass and location of centre of gravity with respect to (w.r.t) to tilting pivot point. Cabin Mass and COG location are very difficult to estimate while designing a new cabin as it is dependent on the maturation of all other cabin aggregates and also the accessories added by the customer. Incorporation design parameter changes like increasing cab tilting angle and increasing torsion bar length, in the later stages of product development, becomes expensive. The objective of this paper is to come up with an optimum design of a single torsion bar tilting employing “Taguchi optimization” for deciding the optimum levels of control factors, which ensures desired performance (i.e tilting effort vs.

Unfavorable climates, fatigue, safety & deprived sleep of driver’s leads to use of AC system for their quick thermal comfort during night with engine ON. This scenario is very critical from a human’s safety & vehicle functionality point of view. This also consumes an additional 10-15% of fuel requirements in AC running conditions. So, to address the social problems of driver’s sleep and pollution-free environment by reducing the use of fossil fuels, there is a need for alternative techniques for air cooling which work during engine OFF condition. Various alternative options for air cooling have been reviewed. Accordingly, the packaging flexibility of phase change material (PCM) technology makes it easy to implement, yet effective usage of large quantity stored PCM, needs optimization. This paper proposes a design of a hybrid air conditioning system for sleeper commercial vehicles using a combined conventional compression and phase change material.

Frame is one of the vital part of Light & Heavy Commercial vehicle which holds all the parts and testing the frame is not a cost effective as the complete vehicle assembly needs to be tested as the individual testing of frame is not formulated for testing. In the development stage of the vehicle we always seek for a quick, cost effective and reliable methodology so that any modification can be made by identifying the failures. In this paper we have addressed this problem by developing a generic frame test methodology by which the frame can be tested in the preliminary stage of development in a cost effective way and reliable way. The Multi Body Dynamics Simulation was carried out and rig was designed comprising of servo hydraulic actuators. The frame was instrumented to acquire the Field, Event and Torture track data for the formulation and verification of the synthetic drives.

This paper explains about the design & development of IHX for HCVs segment and vehicle level validation to get the actual benefits with this technology. Moreover, the data observed during vehicle testing also indicates the improvement in AC System Performance. This experiment was done on HCV platform vehicle with multiple actual test conditions with two designs of IHX. Final result shows the optimized AC system design to achieve better efficiency.

A lightweight multi-material combination of steel and aluminium alloy (Al) is becoming a novel approach towards environmentally sustainable transport systems. Studies show that 10% reduction of vehicle weight results into 3-7% reduction in specific fuel consumption in IC engines and a 13.7% improvement in electric range for electric vehicles. However, dissimilar welding of Al/steel is a key challenge because of incompatible thermo-physical properties (melting point, thermal conductivity, and coefficient of thermal expansion) and low miscibility between Al and steel. The formation of brittle and hard Al-steel intermetallic compound (IMC) at the joint interface is the major concern for dissimilar welding of Al/steel. In this work, efforts are made to check the feasibility of Ni interlayer to control IMC formation at the interface of Al/steel dissimilar welded joint. Resistance spot welding is used to join low carbon steel CR01 and Al AA6061-T6 with pure Ni interlayer.

Lift axles of heavy commercial vehicles are deployed to handle increased payload. These axles of Commercial vehicles are made of low alloy carbon steel materials. Lift axles are designed in hollow condition for weight reduction opportunity. Two types of tube materials are used for the manufacturing of lift axles. These are either Cold Drawn Seamless (CDS) tubes or Hot Finished Seamless (HFS) tube material. The vanadium micro-alloyed steel grade, 20MnV6 is an excellent choice for the manufacturing of lift axles. The 20MnV6 has favorable mechanical properties for lift axles and also offers good weldability. However, lift axles made of 20MnV6 when manufactured in hot-finished condition, shows significant scatter in terms of durability performance. This requires further heat treatment of 20MnV6 to be deployed for reducing the scatter in the material properties to reduce scatter in durability performance and thus increasing the reliability of the lift axles.

Various vehicle manufacturers are launching electric vehicles, which are more sustainable and environmentally friendly. The major component in electric vehicles is the battery, and its performance plays a vital role. Usually, the end of life of a battery in the automobile sector is when the battery capacity reaches 80% of its maximum rated capacity. The capacity of a lithium-ion cell declines with the number of cycles. So, a semi-empirical model is developed for estimating the maximum stored capacity at the end of each cycle. The parameters considered in the model explain the changes in battery internal structure, like capacity losses at different conditions. The capacity estimated using the semi-empirical model is further taken as the inputs for estimating capacity using the Artificial Neural Network (ANN) and Machine Learning (ML) techniques i.e., Linear Regression (LR), Gaussian Process Regression (GPR), Support Vector Machine methods (SVM).