Search Results

Combustion diagnostics of highly diluted mixtures are essential for the estimation of the combustion quality, and control of combustion timing in advanced combustion systems. In this paper, a novel fast response flame detection technique based on active plasma is introduced and investigated. Different from the conventional ion current sensing used in internal combustion engines, a separate electrode gap is used in the detecting probing. Further, the detecting voltage across the electrode gap is modulated actively using a multi-coil system to be slightly below the breakdown threshold before flame arrival. Once the flame front arrives at the probe, the ions on the flame front tend to decrease the breakdown voltage threshold and trigger a breakdown event. Simultaneous electrical and optical measurements are employed to investigate the flame detecting efficacy via active plasma probing under both quiescent and flow conditions.

Hydrogen safety is of great importance in proton exchange membrane fuel cell (PEMFC) systems. Anode pressure control has become a focus point in recent years. The differential pressure between anode and cathode in PEMFC system needs to be carefully controlled under a suitable threshold. In practice, the anode pressure is usually controlled about 20–30kPa higher than the cathode pressure to minimize nitrogen crossover and improve cell stability. High differential pressure could lead to irreversible damage in proton exchange membrane. PID control was the dominant method to control the anode pressure in the past. However, the anode pressure’s fluctuation when hydrogen mass flow suddenly changes is a long-term challenge. As the requirements of control precision are increasingly high, the traditional PID control needs to be improved. Several new control algorithms are presented in recent researches, however, mostly are theoretical and experimental.

Combustion and emission characteristics of diesel and biodiesel blends (soybean methyl ester) were studied in a single-cylinder Direct Injection (DI) engine at different loads and a constant speed. The results show that NOx emission and fuel consumption are increased with increasing biodiesel percentage. Reduction of smoke opacity is significant at higher loads with a higher biodiesel ratio. Compared with the baseline diesel fuel, B20 (20% biodiesel) has a slight increase of NOx emission and similar fuel consumption. Smoke emission of B20 is close to that of diesel fuel. Results of combustion analysis indicate that start of combustion (SOC) for biodiesel blends is earlier than that for diesel. Higher biodiesel percentage results in earlier SOC. Earlier SOC for biodiesel blends is due to advanced injection timing from higher density and bulk modulus and lower ignition delay from higher cetane number.

In this paper, the characteristics of performance and emissions of diesel and biodiesel blends are studied in a four-cylinder DI engine employing common rail injection system. The results show that engine output power is further reduced and brake specific fuel consumption (BSFC) increased with the increase of the blend concentration. B100 provides average reduction by 8.6% in power and increase by 11% in BSFC. With respect to the emissions, although NOx emissions were increased with increasing the blend concentration, the increase depends on the load. Filter smoke number is reduced with increasing the blend concentration. At the same time, NO, NO2 and other specific emissions are also investigated. In addition, difference of performance and emission between standard parameters of ECU and modified parameters of ECU is investigated for B10 and B20 based on same output power. The results show that NOx emission and FSN are still lower than baseline diesel.

In this paper, characteristics of gas emission and particle size distribution are investigated in a common rail diesel engine fueled with biodiesel blends. Gas emission and particle size distribution are measured by AVL FTIR - SESAM and SMPS respectively. The results show that although biodiesel blends would result in higher NOx emissions, characteristics of NOx emissions were also dependent on the engine load for waste cooking oil methyl ester. Higher blend concentration results in higher NO2 emission after two diesel oxidation catalyst s (DOC). A higher blend concentration leads to lower CO and SO2 emissions. No significant difference of Alkene emission is found among biodiesel blends. The particle size distributions of diesel exhaust aerosol consist of a nucleation mode (NM) with a peak below 50N• m and an accumulation mode with a peak above 50N • m. B100 will result in lower particulates with the absence of NM.

The First Firing Cycle (FFC) is very important at cold-start. Misfiring of the first firing cycle can lead to significant HC emissions and affect the subsequent cycles. This paper presents an investigation of characteristics of transient NO emissions in a small LPG SI engine with electronic gaseous injection system. To determine the optimal excess air coefficient ( λ=[A/F]/[A/F]stoic) of the first firing cycle, the emission of instantaneous NO was proposed as a useful criterion to judge if the combustion is occurred or not. A fast response NO detector- Cambustion fNOx400, based on the chemiluminescence's (CLD) method, has been employed to measure continuous, transient emissions of NO during the first firing cycle in the exhaust port of the engine. At the same time, the transient cylinder pressure, instantaneous crankshaft speed of the engine and engine-out HC emissions were measured and recorded.

The fuel cell engine is considered to be the ultimate technical direction for the development of vehicle power. The on-board hydrogen supply system is important in fuel cell system. However, the on-board hydrogen supply system is diversified, and the management is mostly integrated in the engine controller. Thus, the fuel cell engine controller is excessive coupled with design of on-board hydrogen supply system. In order to improve the portability and compatibility of the fuel cell engine controller, an independent controller of the on-board hydrogen supply system is designed. Meanwhile, the hardware and software are developed to control 35Mpa gaseous hydrogen storage system. After being tested in a high-pressure environment, the controller can detect temperature, pressure and ambient hydrogen concentration of the hydrogen supply system. Simultaneously, it can drive and control the hydrogen cylinder valve.

Ethanol reforming gas combined with EGR technology can not only improve thermal efficiency, but also reduce pollutant emission under lean combustion condition. In this investigation, GT-Power is used to carry out one-dimensional simulation model calculation and analysis to explore the combustion characteristics, economy performance of a direct injection gasoline engine when the excess air coefficient (λ) increases from 1 to 1.3 and the ethanol reforming gas mixing ratio increases from 0% to 30% at the working condition of 2000 r/min and 10 bar. Then the EGR system is introduced to deeply discuss the working characteristics of the direct injection gasoline engine when the EGR rate increases from 0% to 20%. The results show that the increase of λ leads to the decrease of in-cylinder pressure and the delay of the peak of cylinder pressure.

In recent years, particulate matters (PM) emissions from gasoline direct injection (GDI) engines have been gradually paid attention to, and the hydrous ethanol has a high oxygen content and a fast burning rate, which can effectively improve the combustion environment. In addition, Exhaust gas recirculation (EGR) can effectively reduce engine NOx emissions, and combining EGR technology with GDI engines is becoming a new research direction. In this study, the effects of hydrous ethanol gasoline blends on the combustion and emission characteristics of GDI engines are analyzed through bench test. The results show that the increase of the proportion of hydrous ethanol can accelerate the burning rate, shorten the combustion duration by 7°crank angle (CA), advance the peak moment of in-cylinder pressure and rate of heat release (RoHR) and improve the combustion efficiency. The hydrous ethanol gasoline blends can effectively improve the gaseous and PM emissions of the GDI engine.

By changing the top-land radial clearance, this paper presents the effect of the piston crevice on the transient HC emissions of the first firing cycle at cold start on an LPG SI Engine. A fast-response flame ionization detector (FFID) was employed to measure transient HC emissions of the first firing cycle. At the same time, the transient cylinder pressure and instantaneous crankshaft speed of the engine were measured and recorded. The results show that increasing 50% crevice volume leads to 25% increase of HC emissions in the lean region and 18% increase of HC emissions in the rich region, however, the 50% increase of crevice volume contributes to 32% decease of HC emissions in the stable combustion region. For LPG SI engine, the HC emissions of the first firing cycle during cold start are relatively low in a wide range of the excess air ratio.

As one of the pollutants that cannot be ignored, soot has a great impact on human health, environment, and energy conversion. In this investigation, the effect of residence time (25ms, 35ms, and 45ms) and ammonia on morphology and nanostructure of soot in laminar ethylene flames has been studied under atmospheric conditions and different flame heights (15 mm and 30 mm). The transmission electron microscopy (TEM) and high-resolution transmission electron microscope (HRTEM) are used to obtain morphology of aggregates and nanostructure of primary particles, respectively. In addition, to analyze the nanostructure of the particles, an analysis program is built based on MATLAB software, which is able to obtain the fringe separation distance, fringe length, and fringe tortuosity parameters of primary particles, and has been verified by the multilayer graphene interlayer distance.

Argon Power Cycle (APC) is an innovative future potential power system for high efficiency and zero emissions, which employs an Ar-O2 mixture rather than air as the working substance. However, APC hydrogen engines face the challenge of knock suppression. Compared to hydrogen, methane has a better anti-knock capacity and thus is an excellent potential fuel for APC engines. In previous studies, the methane is injected into the intake port. Nevertheless, for lean combustion, the stratified in-cylinder mixture formed by methane direct injection has superior combustion performances. Therefore, based on a methane direct injection engine at compression ratio = 9.6 and 1000 r/min, this study experimentally investigates the effects of replacing air by an Ar-O2 mixture (79%Ar+21%O2) on thermal efficiencies, loads, and other combustion characteristics under different excess oxygen ratios. Meanwhile, the influences of varying the methane injection timing are studied.

The Chinese government and industries have proposed strategic plans and policies for automotive renewable-energy transformation in response to China’s commitments to peak the national carbon emissions before 2030 and to achieve carbon neutrality by 2060. We thus analyze the evolution of carbon emissions from the vehicle fleet in China with our data-driven models based on these plans. Our results indicate that the vehicle life-cycle carbon emissions are appreciable, accounting for 8.9% of the national total and 11.3% of energy combustion in 2020. Commercial vehicles are the primary source of automotive carbon emissions, accounting for about 60% of the vehicle energy cycle. Among these, heavy-duty trucks are the most important, producing 38.99% of the total carbon emissions in the vehicle operation stage in 2020 and 52.18% in 2035.

An EURO 3 certified common rail diesel engine was fueled with pure petroleum diesel (EURO 4 standard) and three different alternative blended diesel fuels, 10% biodiesel blended diesel (B10), 10% gas to liquid blended diesel (G10) and 10% water emulsified diesel (E10). Tests were performed at different engine speeds and load states. Particle number concentration and size distribution data were obtained from an engine exhaust particle sizer (EEPS). Over all the working conditions, total particle and nucleation mode particle number concentration among these fuels from high to low were in this order: B10, E10, pure diesel and G10. Proportions for nucleation mode particle over all the operating states in that order were 89%, 82%, 59% and 66%. Particle size distributions of B10 and E10 presented bimodal logarithmic distributions with outstanding nucleation mode peaks at all working conditions.

Biodiesel as a renewable energy is becoming increasingly attractive due to the growing scarcity of conventional fossil fuels. Meanwhile, the development of after-treatment technologies for the diesel engine brings new insight concerning emissions especially the particulate matter pollutants. In order to study the coupling effects of biodiesel blend and CCRT (Catalyzed Continuously Regeneration Trap) on the particulate matter emissions, the particulate matter emissions from an urban bus with and without CCRT burning BD0 and BD10 respectively was tested and analyzed using electrical low pressure impactor (ELPI). The operation conditions included steady state conditions and transient conditions. Results showed that the particulate number-size distribution of BD10 and BD0 both had two peaks in nuclei mode and accumulation mode at the conditions of idle, low speed and medium speed while at high speed condition the particulate number-size distribution only had one peak.

This paper presents a study of the Hydrogen/Argon lifted flames in a hot vitiated co-flow. The effects of the dilution of argon in central fuel, the volume fraction of argon in the central fuel, co-flow temperature and the velocity of the central jet on the flame lift-off length were studied, and the numerical simulation with PDF model were analyzed as well. The results could provide theoretical supports for the research of the hydrogen fueled argon cycle engine which is a potential way not only to increase the indicated thermal efficiency of internal combustion engine but also realize the zero emission. The result shows that at the same boundary condition the central jet of H2+Ar has a lower lift-off length than the central jet of H2+N2. By the numerical simulation, the jet flame of H2+Ar has a higher maximum temperature and maximum OH concentration. It indicated that the dilution of argon could promote the combustion reaction.

Due to the oil crisis and the requirements of energy saving and emission reduction, the research of alternative energy sources for sustainable development has made good progress. Methanol has proven to be a very suitable alternative clean fuel. Compared with gasoline, methanol has a wide range of source and the higher oxygen content and octane number and combustion efficiency, which are beneficial for the engine performance. The effect of different proportions of methanol-gasoline mixed fuel on the performance of SI engine was studied experimentally (lower proportion and higher proportion). It was found that the engine power performance, fuel economy and exhaust emissions were related to the methanol ratio under different operating conditions. In order to adapt to different operating conditions to improve the performance of methanol-gasoline engine, an on-board flexible fuel mixed system was proposed.

Most of the existing energy management strategies for Extended-Range Electric Vehicles (E-REVs) are heuristic, which restricts coordination between the battery and the Range Extender. This paper presents an instantaneous optimization energy management strategy based on the Minimum Loss Power Algorithm (MLPA) for a fuel cell E-REV. An instantaneous loss power function of power train system is constructed by considering the charge and discharge efficiency of the battery, together with the working efficiency of the fuel cell Range Extender. The battery working mode and operating points of the fuel cell Range Extender are decided by an instantaneous optimization module (an artificial neural network) that aims to minimize the loss power function at each time step.

Based on pure diesel, pure biodiesel, and two biodiesel blends at volumetric mixture ratio of 10% and 20%, NEDC emission tests were carried out on a Euro 3-compliant diesel car. Results showed that pure biodiesel and biodiesel blends had decreasing effects on CO and HC emissions under warm-up situations, but deteriorations of CO and HC emissions were observed under cold start-up and low vehicle speed operating conditions, and this caused increasing results of CO and HC emission factors in NEDC tests when substituting pure diesel with both of pure biodiesel and biodiesel blend of 20%. Pure biodiesel aroused an increase in NOX emissions compared with pure diesel, but the two low mixture ratio biodiesel blends were observed in different increasing effects and even decreasing effects on NOX emissions. Only pure biodiesel had limited increasing effects on CO₂ emissions.

Based on a 125cm3 single cylinder SI engine, the designated idle speed was controlled by adjusting of cycle ignition advance angle. By analyzing the effects of different idle speed and throttle open position on three way catalyst (TWC) light-off time and conversion efficiency of HC and CO emissions, combined with the corresponding total HC and CO emissions level, the optimum idle speed and throttle open position at engine's warm-up phase were found by the matching optimum. The present method for engine control strategy is helpful to optimize the warm-up phase emission levels in SI engine with LPG fuel.