Search Results

Squeak and rattle (S&R) problems in body structure and trim parts have become serious issues for automakers because of their influence on the initial quality perception of consumers. In this study, various CAE and experimental methods developed by Hyundai Motors for squeak and rattle analysis of door systems are reported. Friction-induced vibration and noise generation mechanisms of a door system are studied by an intelligent combination of experimental and numerical methods. It is shown that the effect of degradation of plastics used in door trims can be estimated by a numerical model using the properties obtained experimentally. Effects of changes in material properties such as Young's modulus and loss factor due to the material degradation as well as statistical variations are predicted for several door system configurations. As a new concept, the rattle and squeak index is proposed, which can be used to guide the design.

Automobile brake squeal has been experimentally studied in many ways over the past 65 years. A large body of published research and a substantial amount of unpublished work have attempted to experimentally define the variables involved with and describe the system dynamics initiating the friction-induced self-excited vibration. Much of this work has centered on pin on disk type test rigs used to characterize the contact mechanics and/or friction laws without considering the brake system influence. This paper describes a dynamometer designed and constructed to study brake squeal on a system level.

Modeling of liner cavitation corrosion is of increasing significance since new engine design trends could aggravate the problem. Cavitation corrosion is of a complex nature and is affected by numerous coupled factors. A system approach to analyze and assess cavitation corrosion damage is deemed necessary. The approach accounts for the macroscopic and microscopic aspects of the phenomenon that include modeling of piston dynamics, liner transient vibration, pressure wave propagation, bubble dynamics and their effect on material damage. Though detection methods can provide crucial insight of factors that influence the cavitation problem, analysis methods are required at the initial design stage to provide overall engine design optimization and reduce prototype development cost and time. This analytical diagnostic approach provides a powerful tool to give valuable and relatively quick insight in solving engine liner cavitation corrosion problems.

This paper discusses an enhanced active vibration control concept to suppress the dynamic response associated with gear mesh frequencies. In active control application, the control of dynamic gear mesh tonal response is essentially the rejection or suppression of periodical disturbance. Our active control experimental work shows that the existence of un-controlled harmonic result in the increase at these harmonics when applying direct control to the target mesh frequencies. To address this problem, the effect of the existence of un-correlated harmonic components in error signal when applying active control to suppress the target gear mesh harmonics is examined. The proposed adaptive controller that is designed specifically for tackling gear mesh frequency vibrations is based on an enhanced filtered-x least mean square algorithm (FXLMS) with frequency estimation to synthesize the required reference signal.

A proposed multi-coordinate spectral-based inverse substructuring approach is applied experimentally to examine the vibration transmissibility through chassis mounts. In this formulation, the vehicle system is partitioned into two substructures. One substructure comprises of the chassis and suspension, while the second one is the body structure and other attached components. The approach yields the free substructure dynamic characteristics that are extracted from the measured coupled system response spectra. The resultant free substructure transfer functions are verified by comparison of the re-synthesized results to the actual vehicle system measurements. A real life vehicle setup is utilized to demonstrate the salient features and capabilities of this approach, which includes the ability to compute the main structure-borne paths, dynamic interactions between the chassis and body, and interior noise and vibration response.

Sound transmission through the sidewall of an automotive muffler has been studied theoretically and experimentally. Three wall structures: a single shell, double shell and porous-cored shell constructions are considered. Transmission losses through the sidewalls were measured using the two microphone method. Experimental results are compared to one another, and to the corresponding theoretical analysis results, which shows that the mean flow effect is not a significant factor in designing the muffler sidewall.

The analytic wavelet transform (AWT) is a wavelet transform that works much like a transient Fourier transform. Therefore the AWT enables utilizing advantages of both the wavelet transform and Fourier transform. A special form of AWT developed for transient vibration and acoustics signal analyses is applied to various engineering signals in this paper. Application examples include a general time-frequency (T-F) analysis, analysis of exposures to impulsive vibrations and noises, and estimation of reverberation times. Some new definitions such as the T-F noise reduction and frequency weighted time history are defined by taking the advantage of unique capabilities of the AWT. Possible automotive applications of these new concepts are briefly discussed.

A multi-coordinate FRF-based inverse substructuring approach is proposed to partition a vehicle system into two or more substructures, which are coupled at discrete interface points. The joint and free substructure dynamic characteristics are then extracted from the coupled system response spectra. Depending on the actual form of the structural coupling terms, three forms of the coupling matrix are assumed here. The most general one constitutes the non-diagonal form, and the other two simpler cases are the block-diagonal and purely diagonal representations that can be used to simplify testing process and overcome computational problems. The paper is focused on the investigation of the durability of these three formulations when the input FRFs are noise contaminated. A finite element model of a simplified vehicle system is used as the case study.

A spectral-based substructuring approach applying linear frequency response functions (FRF) is proposed for improving the accuracy of simulating the dynamics of coupled systems. The method also applies a least square singular value decomposition (SVD) scheme to overcome the inherent computational deficiency in the basic substructuring formulation. The computational problem is caused by the magnification of measurement errors during any one of the matrix inversion calculations required for this method. The primary objective of applying this approach is to examine the possibility of analyzing higher frequency response that is normally not possible using conventional modeling technique such as the direct finite and boundary element, and lumped parameter techniques. In this study, additional concepts are also evaluated to quantify the limitations and range of applicability of the proposed substructuring approach for simulating the vibration response of complex powertrain structures.

This paper is intended to describe some of the advances in automotive NVH research and applications based on recent developments in the Structural Dynamics Research Laboratory (SDRL) at the University of Cincinnati. State-of-the-art vibro-acoustic research capabilities and infrastructure ranging from advanced vibration modal analysis and spectral techniques for linear and nonlinear automotive systems to computational tools for structure-borne acoustic noise generation, transmission and synthesis problems are discussed. These systems have been devised with the intent of integrating a versatile set of experimental, computational and analytical approaches in order to be able to investigate a variety of crucial automotive NVH concerns. The materials will be grouped into three separate but closely related sets of applications consisting of (i) powertrain noise and vibration control, (ii) analysis and control vehicle system dynamics, and (iii) NVH and sound quality.

Active noise control systems have been gaining popularity in the last couple of decades, due to the deficiencies in passive noise abatement techniques. In the future, a novel combination of passive and active noise control techniques may be applied more widely, to better control the interior sound quality of vehicles. In order to maximize the effectiveness of this combined approach, smarter algorithms will be needed for active noise control systems. These algorithms will have to be computationally efficient, with high stability and convergence rates. This will be necessary in order to accurately predict and control the interior noise response of a vehicle. In this study, a critical review of the filtered-x least mean square (FXLMS) algorithm and several other newly proposed algorithms for the active control of vehicle powertrain noise, is performed. The analysis examines the salient features of each algorithm, and compares their system performance.

An enhanced, frequency domain filtered-x least mean square (LMS) algorithm is proposed as the basis for an active control system for treating powertrain noise. There are primarily three advantages of this approach: (i) saving of computing time especially for long controller’s filter length; (ii) more accurate estimation of the gradient due to the sample averaging of the whole data block; and (iii) capacity for rapid convergence when the adaptation parameter is correctly adjusted for each frequency bin. Unlike traditional active noise control techniques for suppressing response, the proposed frequency domain FXLMS algorithm is targeted at tuning vehicle interior response in order to achieve a desirable sound quality. The proposed control algorithm is studied numerically by applying the analysis to treat vehicle interior noise represented by either measured or predicted cavity acoustic transfer functions.

High speed, precision geared rotor systems are often plagued by excessive vibration and noise problems. The response that is primarily excited by gear transmission error is actually coupled to the large displacement rotational motion of the driveline system. Classical pure vibration model assumes that the system oscillates about its mean position without coupling to the large displacement motion. To improve on this approach and understanding of the influences of the dynamic coupling, a coupled multi-body dynamic and vibration simulation model is proposed. Even though the focus is on hypoid geared rotor system, the model is more general since hypoid and bevel gears have more complicated geometry and time and spatial-varying characteristics compared to parallel axis gears.

Building and operating dependable systems is fundamental to many critical applications, such as designing integrated hardware and software systems for vehicles or satellites. Dependable systems techniques, methods, and tools are developed and used by researchers and practitioners working in widely varying disciplines. In order to provide a unifying framework for the successful dissemination and sharing of dependability results, the development of a dependable systems knowledge base is underway.1 Two database support subsystems are under development: one that manages the storage and retrieval of document information, as well as communicating between the user interface layer and the physical database layer, and another that manages the lexicon of dependability terminology for the user interface layer. The system will provide access to information in a sophisticated, intelligent manner that enables a human user to function more effectively in learning and decision-making capacities.

A new algorithm to detect and to quantify the seriousness of the detected squeak and rattle (S&R) events was developed. A T-F analysis technique called AWT, the Zwicker loudness model and leaky integration are employed to define new concepts we called transient specific loudness time histories and perceived transient loudness time history. The detection threshold of the perceived transient loudness was identified by a clever interpretation of jury test results. The proposed algorithm showed a good promise producing results that are well correlated with the jury tests. The new algorithm developed in this work will be able to automate detection and rating of the S&R events with good accuracy and with minimum possibility of false alarm under normal operating conditions

Squeak and rattle (S&R) noises are undesirable noises caused by friction-induced vibration or impact between surfaces. While several computer programs have been developed to automatically detect and rate S&R events over the years, no reported work has been found that can detect squeak and rattle noises and distinguish them. Because the causes of squeak noises and rattle noises are different, knowing if it is a squeak noise or rattle noise will be very helpful for automotive engineers to choose an appropriate measure to solve the problem. The authors have developed a new algorithm to differentiate squeak noises and rattle noises, and added it to the S&R detection algorithm they had developed previously. The new algorithm utilizes a combination of sound quality metrics, specifically sharpness, roughness, and fluctuation strength.

Acoustically absorptive liners are used in the inlet and exhaust ducts of commercial aircraft engines. A double layer acoustic liner consists of a porous face sheet, a porous septum, an impervious back sheet, and a honeycomb structure. The Acousti-Cap™ technology, developed by Hexcel Corporation, is a significant innovation in the manufacture of double layer acoustic liners. It consists of a non-metallic permeable cap material embedded into each cell of the honeycomb core to create an acoustic septum. This paper presents details of the extensive acoustic testing and analysis carried out to support the development of acoustic liners with embedded mesh-caps.

A new multi-level substructuring approach is proposed to predict the NVH response of driveline systems for the purpose of analyzing rear axle gear whine concern. The fundamental approach is rooted in the spectral-based compliance coupling theory for combining the dynamics of two adjacent subsystems. This proposed scheme employs test-based frequency response functions of individual subsystems, including gear pairs, propshaft, control arms and axle tube, in free-free state as sequential building blocks to synthesize the complete system NVH response. Using an existing driveline design, the salient features of this substructuring approach is demonstrated. Specifically, the synthesized results for the pinion-propshaft assembly and complete vehicle system are presented. The predictions are seen to be in excellent agreement with the experimental data from direct vehicle measurements.

The goal of the presented research is to study the effective operational range for a centrifugal vaneless diffuser turbocharger compressor with ported shroud typically used in diesel engines. A turbocharger bench facility was designed and tested in order to define the performances of the compressor and to better understand the occurrence of instabilities in the housing. Specific emphasis was given to the low mass flow rate region of the compressor performance characteristics where instabilities occur with fluctuations that can be significantly large in the case of surge. Static pressures and dynamic pressure fluctuations were measured at the inlet, the outlet, as well as at different positions around the volute and diffuser sections of the compressor in order to assess the development and propagation of flow instabilities. The dynamic signature of the flow was measured along with the elaboration of the compressor mapping.

The prediction and control of gear vibration and noise has become very important in the design of a quiet, high-quality gearbox systems. The vibratory energy of the gear pair caused by transmission error excitation is transmitted structurally through shaft-bearing-housing assembly and radiates off from exterior housing surface. Most of the previous studies ignore the contribution of components flexibility to the transmission error (TE) and system dynamic responses. In this study, a system level model of axle system with hypoid gear pair is developed, aiming at investigating the effect of the elasticity of the shafts, bearings and housing on TE as well as the contribution of flexible bearings on the dynamic responses. The load distribution results and gear transmission errors are calculated and compared between different assumptions on the boundary conditions.