Search Results

Squeak and rattle (S&R) problems in body structure and trim parts have become serious issues for automakers because of their influence on the initial quality perception of consumers. In this study, various CAE and experimental methods developed by Hyundai Motors for squeak and rattle analysis of door systems are reported. Friction-induced vibration and noise generation mechanisms of a door system are studied by an intelligent combination of experimental and numerical methods. It is shown that the effect of degradation of plastics used in door trims can be estimated by a numerical model using the properties obtained experimentally. Effects of changes in material properties such as Young's modulus and loss factor due to the material degradation as well as statistical variations are predicted for several door system configurations. As a new concept, the rattle and squeak index is proposed, which can be used to guide the design.

This paper discusses an enhanced active vibration control concept to suppress the dynamic response associated with gear mesh frequencies. In active control application, the control of dynamic gear mesh tonal response is essentially the rejection or suppression of periodical disturbance. Our active control experimental work shows that the existence of un-controlled harmonic result in the increase at these harmonics when applying direct control to the target mesh frequencies. To address this problem, the effect of the existence of un-correlated harmonic components in error signal when applying active control to suppress the target gear mesh harmonics is examined. The proposed adaptive controller that is designed specifically for tackling gear mesh frequency vibrations is based on an enhanced filtered-x least mean square algorithm (FXLMS) with frequency estimation to synthesize the required reference signal.

The instability of a viscous liquid jet surrounded by a swirling air stream subject to a 3-D disturbance is predicted by a linear stability model. The effect of flow conditions, fluid properties and nozzle geometry on the disintegration of the liquid jet are investigated by conducting a parametric study. It is observed that the relative velocity between the liquid and gas phases promotes the interfacial aerodynamic instability. The predicted range of wave numbers in which asymmetric modes have higher growth rates than the axisymmetric mode and dominate the instability agrees very well with experimental data. The density ratio significantly enhances the instability as does the axial Weber number. Liquid viscosity inhibits the disintegration process and damps higher helical modes more significantly than the axisymmetric mode. It is observed that air swirl has a stabilizing effect on the liquid jet.

High speed, precision geared rotor systems are often plagued by excessive vibration and noise problems. The response that is primarily excited by gear transmission error is actually coupled to the large displacement rotational motion of the driveline system. Classical pure vibration model assumes that the system oscillates about its mean position without coupling to the large displacement motion. To improve on this approach and understanding of the influences of the dynamic coupling, a coupled multi-body dynamic and vibration simulation model is proposed. Even though the focus is on hypoid geared rotor system, the model is more general since hypoid and bevel gears have more complicated geometry and time and spatial-varying characteristics compared to parallel axis gears.

Building and operating dependable systems is fundamental to many critical applications, such as designing integrated hardware and software systems for vehicles or satellites. Dependable systems techniques, methods, and tools are developed and used by researchers and practitioners working in widely varying disciplines. In order to provide a unifying framework for the successful dissemination and sharing of dependability results, the development of a dependable systems knowledge base is underway.1 Two database support subsystems are under development: one that manages the storage and retrieval of document information, as well as communicating between the user interface layer and the physical database layer, and another that manages the lexicon of dependability terminology for the user interface layer. The system will provide access to information in a sophisticated, intelligent manner that enables a human user to function more effectively in learning and decision-making capacities.

An experimental method to identify damping characteristics of a dynamic system is reported. The method identifies damping matrices of the equation of motion of the system from measured frequency response functions, each different damping mechanism in a distinct matrix. Related experimental techniques and signal processing issues are discussed. Theoretical validation and error study are conducted by applying the method to a theoretical example. The method is applied experimentally to a thin beam with two different damping characteristics for experimental validation and demonstration of the method. Important advantages of the method over existing methods are explained.

A new multi-level substructuring approach is proposed to predict the NVH response of driveline systems for the purpose of analyzing rear axle gear whine concern. The fundamental approach is rooted in the spectral-based compliance coupling theory for combining the dynamics of two adjacent subsystems. This proposed scheme employs test-based frequency response functions of individual subsystems, including gear pairs, propshaft, control arms and axle tube, in free-free state as sequential building blocks to synthesize the complete system NVH response. Using an existing driveline design, the salient features of this substructuring approach is demonstrated. Specifically, the synthesized results for the pinion-propshaft assembly and complete vehicle system are presented. The predictions are seen to be in excellent agreement with the experimental data from direct vehicle measurements.

The goal of the presented research is to study the effective operational range for a centrifugal vaneless diffuser turbocharger compressor with ported shroud typically used in diesel engines. A turbocharger bench facility was designed and tested in order to define the performances of the compressor and to better understand the occurrence of instabilities in the housing. Specific emphasis was given to the low mass flow rate region of the compressor performance characteristics where instabilities occur with fluctuations that can be significantly large in the case of surge. Static pressures and dynamic pressure fluctuations were measured at the inlet, the outlet, as well as at different positions around the volute and diffuser sections of the compressor in order to assess the development and propagation of flow instabilities. The dynamic signature of the flow was measured along with the elaboration of the compressor mapping.

The prediction and control of gear vibration and noise has become very important in the design of a quiet, high-quality gearbox systems. The vibratory energy of the gear pair caused by transmission error excitation is transmitted structurally through shaft-bearing-housing assembly and radiates off from exterior housing surface. Most of the previous studies ignore the contribution of components flexibility to the transmission error (TE) and system dynamic responses. In this study, a system level model of axle system with hypoid gear pair is developed, aiming at investigating the effect of the elasticity of the shafts, bearings and housing on TE as well as the contribution of flexible bearings on the dynamic responses. The load distribution results and gear transmission errors are calculated and compared between different assumptions on the boundary conditions.

Actuator and roller screw mechanism are key components of electromechanical brake (EMB) system in automotive and aerospace industry. The inverted planetary roller screw mechanism (IPRSM) is particularly competitive due to its high load-carrying capacity and small assembly size. For such systems, friction characteristic and friction torque generated from rolling/sliding contacts can be an important factor that affects the dynamic performance as well as vibration behavior. This paper investigates the modeling and simulation of the EMB system in early design stage with special attention to friction torque modelling of IPRSM. Firstly, a step-by-step system model development is established, which includes the controller, servo motor, planetary gear train and roller screw mechanism to describe the dynamic behavior of the EMB system.

Spiral bevel gear dynamics are significantly affected by the flexibilities of shafts and bearings. In this study, a new shaft-bearing model has been proposed for computing the effective support stiffness. The results are applied to the lumped parameter dynamic model of spiral bevel geared rotor system with 3-bearing straddle-mounted pinion configuration. Also, using the multi-degree of freedom lumped parameter dynamic model and quasi-static three-dimensional finite element tooth contact analysis program, the responses of two typical shaft-bearing configurations used in automotive applications, that are the 3-bearing straddle mounted pinion configuration and the 2-bearing overhung mounted pinion configuration, are compared. The comparative analysis along with a set of parametric studies highlights their different contributions to the spiral bevel gear mesh characteristics and dynamic response.

Modeling of elastohydrodynamic lubrication phenomena for the spiral bevel gears is performed in the present study. The damping and the friction coefficient generated from the lubricated contact area will have profound effects on the dynamics of spiral bevel gears. Thus the damping value generated from this friction model will be time varying. This makes the use of constant and empirical damping value in the dynamics of spiral bevel gears questionable. The input geometric and kinematic data required for the elastohydrodynamic lubrication (EHL) simulations are obtained using Tooth Contact Analysis. A full numerical elastohydrodynamic lubrication simulations are carried out using asymmetric integrated control volume (AICV) algorithm to compute the contact pressures. The fast Fourier transform is used to calculate the elastic deformations on the gear surfaces due to contact load.

The changes of dynamic frequency response, commonly used to determine the dynamic characteristic of built-up structures, were studied over the entire fatigue failure process for tensile-shear spot-welded joints. The results of an experimental study showed that the natural frequency varies non-linearly with the fatigue damage fraction. This behavior was modeled using finite element analysis of a progressively growing crack, initiating at the joining surface, then progressing to the outside surface of the specimen, and finally extending from the spot weld nugget. The relationship between dynamic frequency response and crack propagation may be applied to study effect of aging (high mileage) in NVH quality.

Cycloid drives are widely used in the in-wheel motor for electric vehicles due to the advantages of large ratio, compact size and light weight. To improve the transmission efficiency and the load capability and reduce the manufacturing cost, a novel cycloid drive with non-pin design for the application in the in-wheel motor is proposed. Firstly, the generation of the gear pair is presented based on the gearing of theory. Secondly, the meshing characteristics, such as the contact zones, curvature difference, contact ratio and sliding coefficients are derived for performance evaluation. Then, the loaded tooth contact analysis (LTCA) is performed by establishing a mathematical model based on the Hertz contact theory to calculate the contact stress and deformation.

This paper argues in favor of a human-centered (anthropocentric) approach to modern manufacturing. The bases for these arguments are: (a) worker deskilling and creativity issues, (b) economics, and (c) unresolved problems in automation, such as software reliance and costs. Detailed arguments are avoided owing to space limitations. Finally, some issues confronting human-centered manufacturing are raised.

A manual task can be performed based on alternative movement techniques. Ergonomic human motion simulation requires consideration of alternative movement techniques, because they could bring different biomechanical, physiological, and psychophysical consequences. A method for identifying movement techniques from existing motion data was developed. The method is based on a JCV (Joint Contribution Vector) index and statistical clustering. A JCV quantifies a motion's underlying movement technique by computing contributions of individual body joint DOFs (degree-of-freedom) to the achievement of the task goal. Given a set of motions (motion capture data) achieving the same or similar task goals, alternative movement techniques can be identified by 1) representing the motions in terms of JCV and 2) performing a statistical clustering analysis. Performance of this movement technique identification method was evaluated based on a set of stoop and squat lifting motions.

The noise and vibration response of hypoid or bevel geared rotor system, primarily excited by transmission error (TE), and mesh vector and stiffness variations, can be affected significantly by the coupling between the driveline rotor dynamics and gear vibratory response. This is because of the inherent design comprising of non-parallel rotational axes and time-varying as well as spatial-varying gear mesh characteristics. One of the important factors of the driveline system dynamics is the rotor gyroscopic effect that has not been studied extensively in traditional gear dynamics. To address this gap in the literature, this paper attempts to examine the influence of incorporating gyroscopic terms in the hypoid gear dynamic simulation. A multi-degrees-of-freedom, multi-body dynamic model is used as a generalized representation of a hypoid geared rotor system.

Due to the design of lightweight, high speed driveline system, the coupled bending and torsional vibration and rotordynamics must be considered to predict vibratory responses more realistically. In the current analysis, a lumped parameter model of the propeller shaft is developed with Timoshenko beam elements, which includes the effect of rotary inertia and shear deformation. The propeller shaft model is then coupled with a hypoid gear pair representation using the component mode synthesis approach. In the proposed formulation, the gyroscopic effect of both the gear and propeller shaft is considered. The simulation results show that the interaction between gear gyroscopic effect and propeller shaft bending flexibility has considerable influence on the gear dynamic mesh responses around bending resonances, whereas the torsional modes still dominate in the overall frequency spectrum.

Joining of a PdCr Strain Gage with a Hastelloy X carrier shim to Inconel by a rapid infrared processing technique has been investigated at 1150 °C using a nickel based brazing alloy AMS 4777, Ni-7Cr-3Fe-3.2B-4.5Si-.06C in wt%. The effects of the infrared joining parameters on the joint and base material microstructure, joint shear strength, and delamination tendency of the PdCr gage was investigated. Results show that the joint shear strength is as high as 503 MPa when processed at approximately 1150 °C for 120 seconds. Microstructural examinations of the joint with both an optical microscope and a scanning electron microscope indicate that good wetting exists between the brazing alloy with both the Hastelloy X and Inconel 718. And, the Hastelloy X and Inconel 718 exhibits no noticeable change in microstructure due to the rapid processing cycle of the infrared heating process while the stabilized PdCr wire gage shows little change in resistance.

A multi-point hypoid gear mesh model based on 3-dimensional loaded tooth contact analysis is incorporated into a coupled multi-body dynamic and vibration hypoid gear model to predict more detailed dynamic behavior of each tooth pair. To validate the accuracy of the proposed model, the time-averaged mesh parameters are applied to linear time-invariant (LTI) analysis and the dynamic responses, such as dynamic mesh force, dynamic transmission error, are computed, which demonstrates good agreement with that predicted by single-point mesh model. Furthermore, a nonlinear time-varying (NLTV) dynamic analysis is performed considering the effect of backlash nonlinearity and time-varying mesh parameters, such as mesh stiffness, transmission error, mesh point and line-of-action. Simulation results show that the time history of the mesh parameters and dynamic mesh force for each pair of teeth within a full engagement cycle can be simulated.