Search Results

Car components are exposed to the random/harmonic/impact excitation which can result in component failure due to vibration fatigue. The stress and strain loads do depend on local stress concentration effects and also on the global structural dynamics properties. Standardized fatigue testing is long-lasting, while the dynamic fatigue testing can be much faster; however, the dynamical changes due to fatigue are usually not taken into account and therefore the identified fatigue and structural parameters can be biased. In detail: damage accumulation results in structural changes (stiffness, damping) which are hard to measure in real time; further, structural changes change the dynamics of the loaded system and without taking this changes into account the fatigue load in the stress concentration zone can change significantly (even if the excitation remains the same). This research presents a new approach for accelerated vibration testing of real structures.

Approaching engineering limits for the thermal design of battery modules requires virtual prototyping and appropriate models with respect to physical depth and computational effort. A multi-scale and multi-domain model describes the electrochemical behavior of a single battery unit cell in 1D+1D at the level of intra-cell phenomena, and it applies a 3D thermal model at module level. Both models are connected within a common vehicle simulation platform. The models are discussed with special emphasis on battery degradation such as solid electrolyte interphase layer formation, decomposition and lithium plating. The performance of the electrochemical model is assessed by discharge cycles and repeated charge/discharge simulations. The thermal module model is compared to CFD reference data and studied with respect to its grid sensitivity.

The present work introduces an innovative mechanistically based 0D spray model which is coupled to a combustion model on the basis of an advanced mixture controlled combustion approach. The model calculates the rate of heat release based on the injection rate profile and the in-cylinder state. The air/fuel distribution in the spray is predicted based on momentum conservation by applying first principles. On the basis of the 2-zone cylinder framework, NOx emissions are calculated by the Zeldovich mechanism. The combustion and emission models are calibrated and validated with a series of dedicated test bed data specifically revealing its capability of describing the impact of variations of EGR, injection timing, and injection pressure. A model based optimization is carried out, aiming at an optimum trade-off between fuel consumption and engine-out emissions. The findings serve to estimate an economic optimum point in the NOx/BSFC trade-off.

The present work introduces a fully integrated real-time (RT) capable engine and vehicle model. The gas path and drive line are described in the time domain of seconds whereas the reciprocating characteristics of an IC engine are reflected by a crank angle resolved cylinder model. The RT engine model is derived from a high fidelity 1D cycle simulation and gas exchange model to support an efficient and consistent transfer of model data like geometries, heat transfer or combustion. The workflow of model calibration and application is outlined and base ECU functionalities for boost pressure, EGR, smoke and idle speed control are applied for transient engine operation. Steady state results of the RT engine model are compared to experimental data and 1D high fidelity simulations for 19 different engine load points. In addition an NEDC (New European Drive Cycle) is simulated and results are evaluated with data from chassis dynamometer measurements.

Fast charging of batteries at cold conditions faces the challenge of promoting undesired cell degradation phenomena such as lithium plating. The occurrence of lithium plating is strongly related to local surface potentials and temperatures involving the scales of the electrode surface, the unit cell and the entire module or pack. A multi-scale, multi-domain model is presented, enhancing a Newman based unit cell model with consistent models for heat generation and lithium plating and integrating this 1D+1D approach into a thermal 3D model on module level. The basic equations are presented and three different plating models from literature are discussed. The thermal model is assessed in open-loop simulations and the different plating approaches are compared in charge/discharge simulations at different operating conditions. The full multi-scale, multi-domain model is applied as a virtual sensor for model-based control of fast charging at cold conditions.

Fused filament fabrication (FFF) 3D printing technology, one of the most accessible additive manufacturing technologies, can be used to create sensors based on different sensing principles, e.g.: capacitance, inductance, piezoelectricity, piezoresistivity. Piezoresistivity (strain-dependent electrical resistivity) has been predominantly used for the creation of static/quasistatic 3d printed sensors with relatively low sensitivity. This study researches the possibilities of a single-process 3d printing of a piezoresistive accelerometer. Initially, the methods for the axial and cross-axial identification of the piezoresistive properties are discussed. It is shown that the sensitivity is highly dependent on the printing parameters, especially the printing track orientation vs the mechanical load orientation. The research on the sensitivity of a 3D printed piezoresistive structure is extended with an inertial mass-based accelerometer design.

Image-based methods in vibration measurements typically require the use of complex high-speed camera systems. By using the recently introduced Spectral Optical Flow Imaging method, full-field high-frequency vibration data can be measured using a cost-effective still-frame camera. Using a single camera, only the motion perpendicular to the optical axis can typically be identified. Depth information, lost in the 2D imaging process, can be obtained by employing multi-camera imaging systems. Alternatively, the recently introduced frequency domain triangulation method offers a way of measuring full-field 3D deflection shapes using a single, moving camera. This research presents the required theoretical background to combine the Spectral Optical Flow Imaging and frequency-domain triangulation methods in an experimental modal analysis experiment using a single, moving still-frame camera.

Paper outlines a case study on optimal control of a brushless direct-current (BLDC) motor, operating as an Integrated Starter Generator (ISG) in a micro hybrid propulsion system for motorcycles. Main research focus is optimization of BLDC machine torque characteristics, particularly in starter operation mode, in order to improve cranking of the internal combustion engine (ICE) at various operation conditions. Stringent cranking torque demands, limited physical dimensions of the electrical machine and a wide rotational speed range of prototype ICE are most challenging reasons for the exhaustive study of applicable control algorithms in the low rpm range. Two approaches for optimization of torque characteristics are discussed, common known flux-weakening method and the modification of power-switch conduction angle, respectively. The evaluation of most relevant control approaches is based on computer simulation and prototype set-up measurements.

To reduce carbon emissions and mitigate traffic congestion in urban environments, new innovative transportation concepts are required. While public transportation covers certain segments, it cannot supply all possible routes, use cases, and preferences and hence, other solutions are needed as well. Urban drive missions are not typically calling for huge powers or even large energy capacities. In the vehicle design, this should be shown as rightsizing. It is not only the powertrain that should be rightsized but also the vehicle physical dimensions, to enable, e.g., convenient maneuvering. Furthermore, due to the variety of options (walking, biking, scooters, public transportation etc.), one might need a personal vehicle only occasionally, and therefore, a vehicle with shared and multipurpose capabilities would be an asset. Lastly, since small urban vehicles are considered unsafe, improving the safety and general confidence on small vehicles is vital for the market penetration.